Ron & Glenn, thank you. I had already varied the target offline on the other zos lpar, but the target was online to a VM system. The PPRC copy now works.
Thanks for the assist! Joel On Fri, 13 Jun 2008 16:17:38 -0500, Glenn Miller <[EMAIL PROTECTED]> wrote: >Hi Joel, > >I also have twin HDS9980V subsystems with TrueCopy and ShadowImage >installed. I tried your ICKDSK JCL on using two of my 1 cylinder DASD volumes >( they are former XRC utility volumes ) and I believe I received the same error: > >ICKDSF - MVS/ESA DEVICE SUPPORT FACILITIES 17.0 > > PPRCOPY ESTPAIR - > DDNAME(A) - > MODE(COPY) - > PRIMARY(X'992F',43323,X'3E') - > SECONDARY(X'992F',43323,X'3F') - > LSS(X'0F',X'0F') >ICK00700I DEVICE INFORMATION FOR 3F3E IS CURRENTLY AS FOLLOWS: > PHYSICAL DEVICE = 3390 > STORAGE CONTROLLER = 2105 > STORAGE CONTROL DESCRIPTOR = E8 > DEVICE DESCRIPTOR = 0A > ADDITIONAL DEVICE INFORMATION = 4A000035 > TRKS/CYL = 15, # PRIMARY CYLS = 1 >ICK04000I DEVICE IS IN SIMPLEX STATE > >ICK10710I I/O ERROR OCCURRED ON DEVICE 3F3E >CSW = 0EF038 0E000000 CCW = 270EF060 00000021 >000EF060 + 00 62413E3F 0F00F0F0 F0F0F0F4 F3F3F2F3 >000EF070 + 10 992F0F00 F0F0F0F0 F0F4F3F3 F2F3992F >000EF080 + 20 00 >ICKDSF - MVS/ESA DEVICE SUPPORT FACILITIES 17.0 >SENSE = 80000000 BE00000F 58000000 00000000 23124800 992F0F0F >000040C2 00000000 > >ICK34082I A COMMAND WAS RECEIVED THAT IS NOT VALID FOR THIS PPRC >STATE >ICK30003I FUNCTION TERMINATED. CONDITION CODE IS 12 > >ICK00002I ICKDSF PROCESSING COMPLETE. MAXIMUM CONDITION CODE WAS >12 > > >I had the PPRC source volume, UCB address 3F3E and the PPRC target volume, >UCB address 3F3F online to all of my z/OS images. When I varied the PPRC >target volume offline ( as Ron Hawkins suggested ), the command worked: > >ICKDSF - MVS/ESA DEVICE SUPPORT FACILITIES 17.0 > > PPRCOPY ESTPAIR - > DDNAME(A) - > MODE(COPY) - > PRIMARY(X'992F',43323,X'3E') - > SECONDARY(X'992F',43323,X'3F') - > LSS(X'0F',X'0F') >ICK00700I DEVICE INFORMATION FOR 3F3E IS CURRENTLY AS FOLLOWS: > PHYSICAL DEVICE = 3390 > STORAGE CONTROLLER = 2105 > STORAGE CONTROL DESCRIPTOR = E8 > DEVICE DESCRIPTOR = 0A > ADDITIONAL DEVICE INFORMATION = 4A000035 > TRKS/CYL = 15, # PRIMARY CYLS = 1 >ICK04000I DEVICE IS IN SIMPLEX STATE >ICK02203I PPRCOPY ESTPAIR FUNCTION COMPLETED SUCCESSFULLY >ICK02231I DEVICE IS NOW A PEER TO PEER REMOTE COPY VOLUME >ICK00001I FUNCTION COMPLETED, HIGHEST CONDITION CODE WAS 0 > > >I also received the following messages on each of my z/OS images, which I >normally receive whenever I start a PPRC pair on my system: > >IEA494I 3F3E,SO3F3E,PPRC PAIR PENDING,SSID=992F,CCA=3E > >IEA494I 3F3E,SO3F3E,PPRC PAIR FULL DUPLEX,SSID=992F,CCA=3E > >HTH > >Glenn Miller > >---------------------------------------------------------------------- >For IBM-MAIN subscribe / signoff / archive access instructions, >send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO >Search the archives at http://bama.ua.edu/archives/ibm-main.html ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
