All I see once I issue I within ST is, -------------------------------------------------------------------------- Job Information Job name XTBX290 Job class limit exceeded? Job ID JOB00033 Duplicate job name wait? Job schedulable? N/A Time in queue Job class mode Average time in queue Job class held? Position in queue of Active jobs in queue Scheduling environment available on these systems:
And this is the same on both Z/OS systems eventhough $DO JOBQ,READy on 1 system displays this and 1 doesnt 10.52.13 $HASP686 OUTPUT(XTBX290) $HASP686 OUTPUT(XTBX290) OUTGRP=2.1.1,BURST=NO,FCB=****, $HASP686 FLASH=****,FORMS=STD,HOLD=(NONE), $HASP686 OUTDISP=WRITE,PRIORITY=144, $HASP686 PRMODE=LINE,QUEUE=4, $HASP686 RECORDS=(996 OF 996),ROUTECDE=LX290, $HASP686 SECLABEL=,TPJOBID=,TPJOBN=, $HASP686 TSOAVAIL=NO,UCS=****,USERID=P08145, $HASP686 WRITER= Thanks, Tim -----Original Message----- From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On Behalf Of Lizette Koehler Sent: Monday, 07 January, 2013 10:25 AM To: IBM-MAIN@LISTSERV.UA.EDU Subject: Re: Jes2 - $DO JOBQ,READY Tim What panel were you in when you issued the INFO? I typically use ST a lot. Lizette > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] > On Behalf > Of Tim Brown > Sent: Monday, January 07, 2013 8:12 AM > To: IBM-MAIN@LISTSERV.UA.EDU > Subject: Re: Jes2 - $DO JOBQ,READY > > Issuing an "I" in SDSF NP column gets Invalid command > > > Thanks, > > Tim > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] > On Behalf > Of Lizette Koehler > Sent: Monday, 07 January, 2013 10:06 AM > To: IBM-MAIN@LISTSERV.UA.EDU > Subject: Re: Jes2 - $DO JOBQ,READY > > When you say stop working, I assume you mean it is not selecting work. > > Find a job you think should be actioned by the command, then go into > SDSF and issue > an I against that job. See if it matches the criteria for your command. > > Sometimes JES2 will not select work because it does not match the work selection > criteria. I find the I (INFO) command in SDSF sometimes helpful. > > You may not have work that is READY. It may be held ins some fashion. > > Lizette > > > > -----Original Message----- > > From: IBM Mainframe Discussion List > > [mailto:IBM-MAIN@LISTSERV.UA.EDU] On > Behalf > > Of Tim Brown > > Sent: Monday, January 07, 2013 7:52 AM > > To: IBM-MAIN@LISTSERV.UA.EDU > > Subject: Jes2 - $DO JOBQ,READY > > > > This command recently stopped working eventhough there is output in > > the > JES2 output > > that it should display output for. I have an identical Z/OS system > > where > it does display > > the output properly. > > > > Thanks, > > > > Tim Brown > N > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, send > email to > lists...@listserv.ua.edu with the message: INFO IBM-MAIN > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, send > email to > lists...@listserv.ua.edu with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN