There is great wisdom in those words, but remember the fourth son at the Seder: וְשֶׁאֵינוֹ יוֹדֵעַ לִשְׁאוֹל – אַתְּ פְּתַח לוֹ, שֶׁנֶּאֱמַר, וְהִגַּדְתָּ לְבִנְךָ בַּיּוֹם הַהוּא לֵאמֹר, בַּעֲבוּר זֶה עָשָׂה יְיָ לִי בְּצֵאתִי מִמִּצְרָיִם.
Sometimes you have to ask for him. -- Shmuel (Seymour J.) Metz http://mason.gmu.edu/~smetz3 עַם יִשְׂרָאֵל חַי נֵ֣צַח יִשְׂרָאֵ֔ל לֹ֥א יְשַׁקֵּ֖ר ________________________________________ From: IBM Mainframe Discussion List <[email protected]> on behalf of David Spiegel <[email protected]> Sent: Sunday, September 14, 2025 2:25 PM To: [email protected] <[email protected]> Subject: Re: Adding new UCB to IODF External Message: Use Caution אין הביישן למד On 2025-09-14 09:56, Seymour J Metz wrote: > The only dumb question is the one you should have asked but didn't. As long > as you include supporting details with the question and ask in the correct > forum, there's no need to be embarrassed if the answer turns out to be > obvious. BTDT,GTTS. > > -- > Shmuel (Seymour J.) Metz > http://mason.gmu.edu/~smetz3 > עַם יִשְׂרָאֵל חַי > נֵ֣צַח יִשְׂרָאֵ֔ל לֹ֥א יְשַׁקֵּ֖ר > > > > > ________________________________________ > From: IBM Mainframe Discussion List <[email protected]> on behalf of > Peter <[email protected]> > Sent: Sunday, September 14, 2025 12:37 AM > To: [email protected] <[email protected]> > Subject: Adding new UCB to IODF > > > External Message: Use Caution > > > Hello > > Apologies for the dummy question and I must confess that I have inherited > this task recently. I have added a new range of UCB 7000,128 and 7080,128 > > We have lpar TSOA and TSOB both are monoplex on same CEC. Usually the TSOA > is used for building the IODF and after that the exported copy is > transferred to TSOB. > > I have added new series of LCU and LUN in DS8K box. From the ZOS I have > also added the same device pointing to the CU used in DS8K box > > So here is the message I get while doing test only activation and just > wanted to know if these messages are OK ? > > ----------Device------ --#--- --------Control Unit Numbers + > -------- > > / Number Type + CSS OS 1--- 2--- 3--- 4--- 5--- 6--- 7--- > 8--- > > _ 7000,128 3390B 1 5 7000 ____ ____ ____ ____ ____ ____ > ____ > > _ 7080,128 3390A 1 2 7000 ____ ____ ____ ____ ____ ____ > ____ > > ******************************* Bottom of data > ******************************** > > > > > > > > > > > / Sev Msg. ID Message Text > > _ W CBDA333I EDT 01 of OS configuration ZOSEPROD does not use tokens > > # for its esoterics. > > _ W CBDA333I EDT 01 of OS configuration ZOSETEST does not use tokens > > # for its esoterics. > > _ W CBDG061I Switch control unit must be defined for switch 69. > > _ W CBDG061I Switch control unit must be defined for switch 6A. > > _ W CBDG061I Switch control unit must be defined for switch 75. > > _ W CBDG061I Switch control unit must be defined for switch 76. > > > > > > > > / Sev Msg. ID Message Text > > _ I IOS500I ACTIVATE RESULTS > > # TEST DETECTED NO CONDITIONS WHICH WOULD RESULT IN > > # ACTIVATE FAILURE > > _ I NOTE = 0100,SOFTWARE-ONLY CHANGE > > # COMPID=SC1C3 > > _ I NOTE = 010B,H/W AND S/W CONFIGURATION DEFINITIONS WILL > > # BE OUT OF SYNC > > # COMPID=SC1C3 > > _ I CBDA126I ACTIVATE IODF=12,SOFT=NOVALIDATE,TEST command was > > # accepted. > > _ I CBDA854I Changes to Coupling Facility and function elements are > processed. > > > > Any guidance and pointers are much appreciated. > > Regards > Peter > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN > > > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
