Try using FIX on your audit to see if it cleans up the error.
-----Original Message----- From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On Behalf Of willie bunter Sent: Thursday, July 27, 2017 10:36 AM To: IBM-MAIN@LISTSERV.UA.EDU Subject: Re: DFHSM QUESTION Lizette, The reason why I think that it is a problem because after I run the AUDIT using NOFIX the output shows the dsn (*err 40). I do not see this for other LPARS. My understanding is that if any errors appear a clean up is needed to be initiated. In this case only ERR 40 appears. -------------------------------------------- On Thu, 7/27/17, Lizette Koehler <stars...@mindspring.com> wrote: Subject: Re: DFHSM QUESTION To: IBM-MAIN@LISTSERV.UA.EDU Received: Thursday, July 27, 2017, 10:22 AM That does not seem to be a failure. It just states the record you tried to delete no longer exists in HSM. Once the record is deleted, it cannot be deleted again. Why do you think this is a failure? The message ARC0195I is all you need to focus on. The ARC1001 or ARC1615I just states the command could not do any work. Lizette > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On > Behalf Of willie bunter > Sent: Thursday, July 27, 2017 6:32 AM > To: IBM-MAIN@LISTSERV.UA.EDU > Subject: Re: DFHSM QUESTION > > Brian, > > I tried that out however it didn't work (record not found). Below is the > output: > > ARC0195I TYPE B, KEY DB2.ARCHLOG2.A0091613, FIXCDS DELETE, ERROR=RECORD NOT > ARC0195I (CONT.) FOUND > ARC1001I FIXCDS B DB2.ARCHLOG2.A0091613 DELETE COMMAND FAILED, RC=0015, > ARC1001I (CONT.) REAS=0000 > ARC1615I FIXCDS COMMAND REJECTED > -------------------------------------------- > On Wed, 7/26/17, Brian Fraser <brianmfra...@gmail.com> wrote: > > Subject: Re: DFHSM QUESTION > To: IBM-MAIN@LISTSERV.UA.EDU > Received: Wednesday, July 26, 2017, 9:23 PM > > If you just want to > get rid of > the backup, then you can do the following. > > HSEND FIXCDS B > DB2.ARCHLOG2.A0091613 *DELETE* > > Regards > Brian > > On Thu, Jul 27, 2017 at 1:30 > AM, retired mainframer < > retired-mainfra...@q.com> > wrote: > > > Please show the > complete AUDIT and BDELETE commands you are using. > > > > Did you look up ERR40 > in the "Error Codes and Diagnosis" section (section > 3 in my copy) of the > "Using the AUDIT Command" chapter (my chapter 67)? > > The table (51) identifies several > possible causes and corrective actions. > > > BDELETE is the proper action for only one of the causes. > > > > > -----Original > Message----- > > > From: IBM Mainframe > Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On > > Behalf Of willie > > bunter > > Sent: Wednesday, July 26, 2017 7:27 AM > > To: IBM- > > m...@listserv.ua.edu > > Subject: DFHSM QUESTION > > > > Good Day, > > > > > > I ran an AUDIT of the BCDS. I was 99% successfull of performing a > > clean > up execept for > > the following type dsns: > > > ERR 40 DB2.ARCHLOG2.A0091613 > > > > HSMBACK.BACK.T592617.DB2.ARCHLOG2.I8257 MISSING > > FIXCDS B > DUMMY.RECOVER.MCB CREATE(X'00000014' X'0098257F') > > FIXCDS B > DUMMY.RECOVER.MCB PATCH(X'0000002E' BITS(1.1.....)) > > FIXCDS B > DUMMY.RECOVER.MCB PATCH(X'00000030' X'000100010001') > > FIXCDS B > DUMMY.RECOVER.MCB > EXPAND(X'00000040') > > > > FIXCDS B DUMMY.RECOVER.MCB PATCH(X'00000050' + > > > > > X'404040404040404040404040404040404040404040404040404040404040 > > 404040404040 > > > > 404 > > > FIXCDS B DUMMY.RECOVER.MCB > PATCH(X'00000050' > > > > HSMBACK.BACK.T592617.DB2.ARCHLOG > > > > FIXCDS B DUMMY.RECOVER.MCB PATCH(X'00000082' > BITS(01000010)) > > > BDELETE > DUMMY.RECOVER.MCB > > > FIXCDS B > DUMMY.RECOVER.MCB DELETE > > > END OF > - ENHANCED AUDIT - LISTING - > > > > > > > I tried a HSEND BDELETE > 'DB2.ARCHLOG2.A0091613' ALL . The command which > I > > ran in batch was > successful however when I ran another AUDIT the entry > appears. I tried a > > > HSEND FIXCDS B DB2.ARCHLOG2.A0091613. Again the command was > successful, > > however the AUDIT says otherwise. > > > > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN The information contained in this message is proprietary and/or confidential. If you are not the intended recipient, please: (i) delete the message and all copies; (ii) do not disclose, distribute or use the message in any manner; and (iii) notify the sender immediately. In addition, please be aware that any message addressed to our domain is subject to archiving and review by persons other than the intended recipient. Thank you. ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
