So is everything is correct now? Or do you have more questions.
Otherwise I think your issues are resolved. Lizette > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On > Behalf Of willie bunter > Sent: Thursday, July 27, 2017 8:58 AM > To: IBM-MAIN@LISTSERV.UA.EDU > Subject: Re: DFHSM QUESTION > > I tried out the BDELETE and as expected the record was not found. > > ARC0195I TYPE B, KEY DB2.ARCHLOG2.A0091613, FIXCDS DELETE, ERROR=RECORD NOT > ARC0195I (CONT.) FOUND > ARC1001I FIXCDS B DB2.ARCHLOG2.A0091613 DELETE COMMAND FAILED, RC=0015, > ARC1001I (CONT.) REAS=0000 > ARC1615I FIXCDS COMMAND REJECTED > > Below is the HLIST: > ARC0138I NO BCDS INFORMATION FOUND FOR DATASET DB2.ARCHLOG2.A0091613 > -------------------------------------------- > On Thu, 7/27/17, Lizette Koehler <stars...@mindspring.com> wrote: > > Subject: Re: DFHSM QUESTION > To: IBM-MAIN@LISTSERV.UA.EDU > Received: Thursday, July 27, 2017, 10:52 AM > > At this point, just take one step > back. > > You wanted to delete > a backup version from HSM. > > The dataset is either DB2.ARCHLOG2.A0091613 or DB96.ARCHLOG2.B0000778 > > Issue an HLIST > DSN('DB96.ARCHLOG2.B0000778') BCDS or HLIST DSN('DB2.ARCHLOG2.A0091613 > ') BCDS > > > If you do not > see any backup datasets listed for these datasets, then you have deleted > the backup copies. > > If you still see BCDS entries, then you may need to do more BDELETE > commands. > > AUDIT is used to verify content in HSM. However, it may create confusion > with its results. > > I rarely use AUDIT. If the > BDELETE works or there are no longer any BCDS entries, I will not issue > AUDIT commands. > > > If you could provide the > description of the problem you are trying to solve with BDELETE and AUDIT, > that will be helpful. > > From what you have posted so far, the BDELETE looks like it was successful > at some point. > > > For further > analysis, issue the command BACKDS 'DB2.ARCHLOG2.A0091613' > > Then do the HLIST > DSN('DB2.ARCHLOG2.A0091613') BCDS and see if you get an entry > > > Next do the BDELETE command for > DB2.ARCHLOG2.A0091613 > > > Repeat the HLIST command. > > > If there are > no entries in the BCDS for this dataset, that should show the process in > HSM is working. > > > Lizette > > > > -----Original > Message----- > > From: IBM Mainframe > Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On > Behalf Of willie > bunter > > Sent: Thursday, July 27, 2017 6:53 AM > > > To: IBM-MAIN@LISTSERV.UA.EDU > > Subject: Re: DFHSM QUESTION > > > > Here are the > commands I tried : > > HSEND FIXCDS B > DB96.ARCHLOG2.B0000778 (message received) : > > > > ARC0195I TYPE B, KEY > DB96.ARCHLOG2.B0000778, FIXCDS DISPLAY, ERROR=RECORD NOT > ARC0195I (CONT.) > FOUND > ARC1001I FIXCDS B DB96.ARCHLOG2.B0000778 COMMAND FAILED, RC=0015, > REAS=0000 > ARC1615I FIXCDS COMMAND REJECTED > > HSEND BDELETE > 'DB2.ARCHLOG2.A0091613' ALL No error message received. > > > > I > looked at the ERR 40 in the doc. It describes my problem however it is > > not clear what I should do. In this case the B record does not exist or > > missing. > > for example > it says "If the backup version (C) record references a data set > (B) > record that does not exist, then a new (B) record is created and the > > version added". Not usre ...then a new(B) record is created and the > version > added. > > > > I do not understand this. Any > suggestions? > > > -------------------------------------------- > > On Wed, 7/26/17, retired mainframer <retired-mainfra...@q.com> > wrote: > > > > Subject: > Re: DFHSM QUESTION > > To: IBM-MAIN@LISTSERV.UA.EDU > > Received: Wednesday, July 26, 2017, 1:30 PM > > Please show the > complete AUDIT > and BDELETE commands you are using. > > > > Did you look up ERR40 in the "Error > Codes and Diagnosis" section (section 3 > in my copy) of the "Using the > AUDIT Command" chapter (my chapter 67)? The > table (51) identifies > several possible causes and corrective > actions. BDELETE is the proper > action for only one of the causes. > > > > > > > -----Original Message----- > > > From: IBM > > > Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On > Behalf Of > > willie bunter > Sent: Wednesday, July 26, 2017 7:27 AM > To: > IBM- > > m...@listserv.ua.edu > > Subject: DFHSM QUESTION > > Good Day, > > I ran > an AUDIT of the > BCDS. I was 99% successfull of performing a clean up > execept for > the > following type > dsns: > > > ERR 40 > DB2.ARCHLOG2.A0091613 > > > > HSMBACK.BACK.T592617.DB2.ARCHLOG2.I8257 > > MISSING > > > > FIXCDS B DUMMY.RECOVER.MCB > > > CREATE(X'00000014' X'0098257F') > > > FIXCDS B DUMMY.RECOVER.MCB > > PATCH(X'0000002E' > BITS(1.1.....)) > > > FIXCDS B > DUMMY.RECOVER.MCB > > > PATCH(X'00000030' X'000100010001') > > > FIXCDS B DUMMY.RECOVER.MCB > > EXPAND(X'00000040') > > > FIXCDS B > > > DUMMY.RECOVER.MCB PATCH(X'00000050' + > > > > > > > > > X'404040404040404040404040404040404040404040404040404040404040404040404040 > > > 404 > > > > FIXCDS B > > DUMMY.RECOVER.MCB > PATCH(X'00000050' > > > > HSMBACK.BACK.T592617.DB2.ARCHLOG > > > > FIXCDS B DUMMY.RECOVER.MCB > > > PATCH(X'00000082' BITS(01000010)) > > > BDELETE DUMMY.RECOVER.MCB > > > FIXCDS B DUMMY.RECOVER.MCB > DELETE > > > END OF - ENHANCED > AUDIT - LISTING > > - > > > > > > I tried > a HSEND > > BDELETE > 'DB2.ARCHLOG2.A0091613' ALL . The command which I > ran in batch > was > successful however when I ran another AUDIT the entry appears. I tried > > a > HSEND FIXCDS B DB2.ARCHLOG2.A0091613. Again the command was > > successful, > however the AUDIT says otherwise. > > > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
