If I understand correctly you can't get the PC to connect to the OSA-ICC port. Can you ping the IP address of the OSA port from the PC? If not, then it sounds like a network problem. Do you get any error message on the PC when you try to connect to the OSA port?
Paul Feller AIT Mainframe Technical Support [EMAIL PROTECTED] (319)-355-7824 -----Original Message----- From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of James M Sent: Monday, September 10, 2007 11:32 AM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: z/VM 5.2 ICC console connection problems OK thanks. I varied all off first and the all on. I saw all the devices go off and come back online on operx. ...but it didn't help - I still cannot connect from the pc to the icc port. I did enable the console cuu before trying. On 9/10/07, Ivica Brodaric <[EMAIL PROTECTED]> wrote: > Yes. It has to be offline to all LPARs in order to reset itself. > > > On 11/09/2007, James M <[EMAIL PROTECTED]> wrote: > > maybe we're getting someplace. > > are you suggesting that I have to config path off in all the lpars > > and then config it on in all? > > what I did was off/on in lpar 1 - off/on lpar2 and so on. > > > > > > On 9/10/07, Ivica Brodaric <[EMAIL PROTECTED]> wrote: > > > Did you vary it offline from all LPARs at the same time? > > > > > > > > > On 11/09/2007, James M <[EMAIL PROTECTED]> wrote: > > > > I did try toggling the chpid off/on in each of the lpars but I'm > > > > not sure it worked properly. > > > > it went from online/online to online/standby. I never did see > > > > the current state go to offline! > > > > > > > > On 9/10/07, Rich Smrcina <[EMAIL PROTECTED] > wrote: > > > > > Resetting the ICC port will only affect the ICC users, if most > > > > > of > your > > > > > users are coming in through VM's TCP/IP stack, it's not using > > > > > the > ICC. > > > > > If only your console or datacenter users use the ICC, you can > > > > > reset > it > > > > > without affecting your users. > > > > > > > > > > James M wrote: > > > > > > device shows enabled. > > > > > > I cannot reset the port on the hmc since it's a dual port > > > > > > card > (icc & > > > > > > tcpip) and that would mean dropping many vm & os telnet clients. > > > > > > > > > > > > On 9/10/07, David Kreuter <[EMAIL PROTECTED] > wrote: > > > > > >> > > > > > >> > > > > > >> from the hmc try resetting the OSA port at the chpid level. > > > > > >> David > > > > > >> > > > > > >> ______________________________ __ > > > > > >> From: The IBM z/VM Operating System on behalf of James M > > > > > >> Sent: Mon 9/10/2007 10:47 AM > > > > > >> To: IBMVM@LISTSERV.UARK.EDU > > > > > >> Subject: [IBMVM] z/VM 5.2 ICC console connection problems > > > > > >> > > > > > >> > > > > > >> > > > > > >> > > > > > >> Over the weekend an operator "I did something..I don't know what" > > > that > > > > > >> has rendered the ICC vm console unusable. > > > > > >> I tried disable/enable cuu, vary off/on path to cuu and > > > > > >> dropping > the > > > > > >> session from the HMC ICC utilities menu all to no avail. > > > > > >> Can someone please suggest other possible solutions. Thanks > > > > > >> -Jim > > > > > >> > > > > > >> > > > > > > > > > > > > > > > > -- > > > > > Rich Smrcina > > > > > VM Assist, Inc. > > > > > Phone: 414-491-6001 > > > > > Ans Service: 360-715-2467 > > > > > rich.smrcina at vmassist.com > > > > > http://www.linkedin.com/in/richsmrcina > > > > > > > > > > Catch the WAVV! http://www.wavv.org > > > > > WAVV 2008 - Chattanooga - April 18-22, 2008 > > > > > > > > > > > > > > > > > > >