Hi All, I have been success in setting up a OpenVPN server and I am able to connect to the server from my clients, but clients cannot ping behind VPN eth1 interfaces ie from my client I can ping VPNServer eth1 (192.168.50.30), but cannot ping to the other side, It has to do some setting with route command
see this traceroute results from the client joseph@saji:~$ traceroute 192.168.50.30 traceroute to 192.168.50.30 (192.168.50.30), 30 hops max, 60 byte packets 1 192.168.50.30 (192.168.50.30) 294.031 ms 294.041 ms 294.050 ms joseph@saji:~$ but when I do trace route to some IP inside the LAN it stops joseph@saji:~$ traceroute 192.168.50.10 traceroute to 192.168.50.10 (192.168.50.10), 30 hops max, 60 byte packets 1 10.28.0.1 (10.28.0.1) 296.795 ms 296.802 ms 296.803 ms 2 * * * 3 * * * 4 * * * So it reaches till the VPN server tunnel interface (10.28.0.1) then gets confused, we have to tell the packet from 10.28.0.1 to go to eth1. I tried with some route command which all was not correct Like to get help, details of the network are given below My VPN Client ip is 192.168.3.101 and My VPN Server interfaces are eth0= connected to the public IP eth1= interface is 192.168.50.30/24 I did a openvpn connection from my client to OpenVP Server now my client interfaces are eth0 = 192.168.3.101 tun0 = 10.28.0.10 My Server interfaces are eth0 = Public IP eth1 = 192.168.50.30/24 tun0 = 10.28.0.1 My Server route -n command shows [root@reserved-94 openvpn]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.10.10.11 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.28.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 XXX.XX.XX.XX 0.0.0.0 255.255.255.252 U 1 0 0 eth0 10.28.0.0 10.28.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.50.0 0.0.0.0 255.255.255.0 U 1 0 0 eth1 0.0.0.0 XXX.XX.XX.XX 0.0.0.0 UG 0 0 0 eth0 Advice and help requested thanks Joseph John -- -- "Freedom is the only law". "Freedom Unplugged" http://www.ilug-tvm.org You received this message because you are subscribed to the Google Groups "ilug-tvm" group. To control your subscription visit http://groups.google.co.in/group/ilug-tvm/subscribe To post to this group, send email to ilug-tvm@googlegroups.com To unsubscribe from this group, send email to ilug-tvm-unsubscr...@googlegroups.com For details visit the google group page: http://groups.google.com/group/ilug-tvm?hl=en --- You received this message because you are subscribed to the Google Groups "Free Software Users Group, Thiruvananthapuram" group. To unsubscribe from this group and stop receiving emails from it, send an email to ilug-tvm+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.