1 Hi Don,
2 It seems that we agree in the area of keeping the iommu active and
using it to
3 isolate the legacy DMA. We also agree that the device's IO driver
should be
4 the software that deals with the device (e.g.: resets it, etc.)
5
6 It also seems that there are several differences in our two approaches
to how
7 the iommu is then used to accomplish this common goal.
8
9 More detailed replies are among your comments below.
10
11 On Monday 4/7/2014: Don Dutile wrote:
12 >On 01/10/2014 05:07 PM, Bill Sumner wrote:
13 >> v2->v3:
14 >> 1. Commented-out "#define DEBUG 1" to eliminate debug messages
15 >> 2. Updated the comments about changes in each version in all patches
in the set .
16 >> 3. Fixed: one-line added to Copy-Translations" patch to initialize
the iovad
17 >> struct as recommended by Baoquan He [b...@redhat.com]
18 >> init_iova_domain(&domain->iovad, DMA_32BIT_PFN);
19 >>
20 >> v1->v2:
21 >> The following series implements a fix for:
22 >> A kdump problem about DMA that has been discussed for a long time.
That is,
23 >> when a kernel panics and boots into the kdump kernel, DMA started by
the
24 >> panicked kernel is not stopped before the kdump kernel is booted and
the
25 >> kdump kernel disables the IOMMU while this DMA continues. This
causes the
26 >> IOMMU to stop translating the DMA addresses as IOVAs and begin to
treat them
27 >> as physical memory addresses -- which causes the DMA to either:
28 >> (1) generate DMAR errors or (2) generate PCI SERR errors or (3)
transfer
29 >> data to or from incorrect areas of memory. Often this causes the
dump to fail.
30 >>
31 >> This patch set modifies the behavior of the iommu in the (new)
crashdump kernel :
32 >> 1. to accept the iommu hardware in an active state,
33 >> 2. to leave the current translations in-place so that legacy DMA
will continue
34 >> using its current buffers until the device drivers in the
crashdump kernel
35 >> initialize and initialize their devices,
36 >> 3. to use different portions of the iova address ranges for the
device drivers
37 >> in the crashdump kernel than the iova ranges that were in-use at
the time
38 >> of the panic.
39 >>
40 >> Advantages of this approach:
41 >> 1. All manipulation of the IO-device is done by the Linux
device-driver
42 >> for that device.
43 >> 2. This approach behaves in a manner very similar to operation
without an
44 >> active iommu.
45 >
46 >Sorry to be late to the game.... finally getting out of a deep hole &
47 >asked to look at this proposal...
48 >
49 >Along this concept -- similar to operation without an active iommu --
50 >have you considered the following:
51 >a) if (this is crash kernel), turn *off* DMAR faults;
52 I did look at turning off DMAR faults and, although I chose not to
disable
53 them in my current patch submissions, I think that this is still an
open area
54 to explore -- especially for any cases where DMAR faults were already
occurring
55 in the panicked kernel. We may want to explore expanding the patches to
cover the
56 case where legacy DMAR faults are still occurring in the kdump kernel.
57 I would recommend tackling this as a separate follow-on effort.
58 In testing my patches, I have seen no new DMAR faults introduced by
them.
59 In fact, the transition is seamless, leaving no time window where (for
60 instance) RMRR DMA would fail.
61
62 >b) if (this is crash kernel), isolate all device DMA in IOMMU
63 I agree, the iommu is a great resource to isolate device DMA into safe
memory
64 areas -- we should leave it active and use it.
65
66 >b) as second kernel configures each device, have each device to use
IOMMU hw-pass through,
67 > i.e., the equivalent of having no IOMMU for the second, kexec'd
kernel
68 > but, having the benefit of keeping all the other (potentially bad)
devices
69 > sequestered / isolated, until they are initialized & re-configured
in the seco nd kernel,
70 > *if at all* -- note: kexec'd kernels may not enable/configure all
devices tha t
71 > existed in the first kernel (Bill: I'm sure you know this, but
others may not ).
72 >
73 >RMRR's that were previously setup could continue to work if they are
skipped in s tep (b),
74 >unless the device has gone mad/bad. In that case, re-parsing the RMRR
may or may not
75 >clear up the issue.
76 >
77 >Additionally, a tidbit of information like "some servers force NMI's
on DMAR faul ts,
78 >and cause a system reset, thereby, preventing a kdump to occur"
79 >should have been included as one reason to stop DMAR faults from
occurring on kex ec-boot,
80 >in addition to the fact that a flood of them can lock up a system.
81 If a server will "force NMI's on DMAR faults, and cause a system reset,
thereby,
82 preventing a kdump to occur" then if the panicked kernel was already
causing DMAR
83 faults our dump is already doomed. If the panicked kernel was *not*
causing
84 DMAR faults, then any kdump technique that does not introduce any new
DMAR
85 fault conditions should be ok.
86 >
87 >Again, just turning off DMAR fault reporting for the 'if (this is
crash kernel)',
88 >short-term workaround sounds a whole lot less expensive to implement,
as well as
89 >'if (this is crash kernel), force hw-passthrough'.
90 Actually it may not be all that less expensive once the details of
91 its implementation are explored.
92
93 1. Especially with the current patches already available and somewhat
tested.
94
95 2. I think that implementing what you suggest will require some
manipulation
96 of the translation tables and their base register in the iommu -- code
97 that seems likely to be similar to what is in the patches. If this
effort
98 goes in the direction you suggest, perhaps some of the code in the
patches
99 could be of help.
100 >
101 >If the IO devices are borked to the point that they won't complete DMA
properly,
102 >with or without IOMMU, the system is dead anyhow, game over.
103 True, and there is probably not much we can do about it.
104 >
105 >Finally, copying the previous IOMMU state to the second kernel, and
hoping
106 >that the cause of the kernel crash wasn't an errant DMA (e.g., due to
a device going bad,
107 >or it's DMA-state being corrupted & causing an improper IO), is
omitting an important failure
108 >case/space.
109 I am not just "hoping":
110 a. The iommu isolates all device DMA to buffers dictated by the
translation
111 tables -- whether those tables are the ones I copied or the ones that
were
112 created in kdump to isolate the DMA to new memory buffers. By design,
113 the iommu hardware very strongly limits what memory a device can access
--
114 even in the cited case where the device has a corrupted state and may be
115 making all sorts of bad requests.
116
117 b. The iommu tables of course could be "hosed" which would cause
problems; but
118 in the normal case the translation tables are updated only by a small
amount
119 of software in the iommu driver and the dma software. This fortunately
120 provides a relatively solid foundation that ensures the integrity of the
121 tables that the iommu hardware is using for translations.
122
123 c. Since the tables the patches copy come from a panicked kernel, they
are
124 vetted as well as we can before they are copied and used in the kdump
kernel.
125 This happens early in kdump __init before any of the copied tables are
used
126 by the kdump iommu driver software. Currently if the patches find any
bad
127 tables, they simply bail-out of taking the dump -- another area where
they
128 might be expanded -- to do something different in this case.
129
130 d. The most vulnerable place I have noticed for bugs in the Linux
kernel to
131 generate bad translations in the iommu tables is the short path in the
132 device drivers between obtaining the memory buffer from some allocator
133 and then obtaining an IOVA for that buffer from the dma subsystem.
134 If the device driver loses the buffer address and/or hands the dma
subsystem
135 a different buffer address when it requests the IOVA, then the iommu has
136 no way of knowing that the buffer address is bad, creates the
translation,
137 and bad things happen.
138
139 >Keeping the first-kernel DMA isolated (IOMMU on, all translations off,
all DMAR faults off),
140 >and then allowing each device (driver) configuration to sanely reset
the device &
141 >start a new (hw-passthrough) domain seems simpler and cleaner, for
this dump-and-run kernel
142 >effort.
143 As you explore the technique of turning-off translations, a few
questions come to mind:
144 1. How is the RMRR activity supported? Any time windows where the
device cannot
145 initiate a DMA transaction will need to be minimized.
146
147 2. How does the iommu code know when the device has been reset by its
driver
148 so that it is now safe to program new translations into the iommu
tables?
149 The first communication the iommu code gets from the driver is when the
driver
150 requests a translation via the dma services. I see no ordering
requirement
151 on the driver that it must have already reset the device at this time.
152 The driver may be accumulating buffers that it will later send to the
device
153 during the reset sequence for use as work queues, status inputs, or data
154 buffers.
155
156 3. What happens if hardware pass-through is enabled for a device
before the
157 driver resets it ? This would seem to allow any legacy DMA to run
rampant.
158 >
159 >- Don
160 >
161 >> 3. Any activity between the IO-device and its RMRR areas is handled
by the
162 >> device-driver in the same manner as during a non-kdump boot.
163 >> 4. If an IO-device has no driver in the kdump kernel, it is simply
left alone.
164 >> This supports the practice of creating a special kdump kernel
without
165 >> drivers for any devices that are not required for taking a
crashdump.
166 >>
167 >> Changes since the RFC version of this patch:
168 >> 1. Consolidated all of the operational code into the "copy..."
functions.
169 >> The "process..." functions were primarily used for diagnostics
and
170 >> exploration; however, there was a small amount of operational
code that
171 >> used the "process..." functions.
172 >> This operational code has been moved into the "copy..."
functions.
173 >>
174 >> 2. Removed the "Process ..." functions and the diagnostic code that
ran
175 >> on that function set. This removed about 1/4 of the code --
which this
176 >> operational patch set no longer needs. These portions of the
RFC patch
177 >> could be formatted as a separate patch and submitted
independently
178 >> at a later date.
179 >>
180 >> 3. Re-formatted the code to the Linux Coding Standards.
181 >> The checkpatch script still finds some lines to complain about;
182 >> however most of these lines are either (1) lines that I did not
change,
183 >> or (2) lines that only changed by adding a level of indent which
pushed
184 >> them over 80-characters, or (3) new lines whose intent is far
clearer when
185 >> longer than 80-characters.
186 >>
187 >> 4. Updated the remaining debug print to be significantly more
flexible.
188 >> This allows control over the amount of debug print to the
console --
189 >> which can vary widely.
190 >>
191 >> 5. Fixed a couple of minor bugs found by testing on a machine with a
192 >> very large IO configuration.
193 >>
194 >> At a high level, this code operates primarily during iommu
initialization
195 >> and device-driver initialization
196 >>
197 >> During intel-iommu hardware initialization:
198 >> In intel_iommu_init(void)
199 >> * If (This is the crash kernel)
200 >> . Set flag: crashdump_accepting_active_iommu (all changes below
check this)
201 >> . Skip disabling the iommu hardware translations
202 >>
203 >> In init_dmars()
204 >> * Duplicate the intel iommu translation tables from the old kernel
205 >> in the new kernel
206 >> . The root-entry table, all context-entry tables,
207 >> and all page-translation-entry tables
208 >> . The duplicate tables contain updated physical addresses to link
them toget her.
209 >> . The duplicate tables are mapped into kernel virtual addresses
210 >> in the new kernel which allows most of the existing iommu code
211 >> to operate without change.
212 >> . Do some minimal sanity-checks during the copy
213 >> . Place the address of the new root-entry structure into "struct
intel_iommu "
214 >>
215 >> * Skip setting-up new domains for 'si', 'rmrr', 'isa'
216 >> . Translations for 'rmrr' and 'isa' ranges have been copied from
the old ker nel
217 >> . This patch has not yet been tested with iommu pass-through
enabled
218 >>
219 >> * Existing (unchanged) code near the end of dmar_init:
220 >> . Loads the address of the (now new) root-entry structure from
221 >> "struct intel_iommu" into the iommu hardware and does the
hardware flushes .
222 >> This changes the active translation tables from the ones in the
old kernel
223 >> to the copies in the new kernel.
224 >> . This is legal because the translations in the two sets of
tables are
225 >> currently identical:
226 >> Virtualization Technology for Directed I/O. Architecture
Specification,
227 >> February 2011, Rev. 1.3 (section 11.2, paragraph 2)
228 >>
229 >> In iommu_init_domains()
230 >> * Mark as in-use all domain-id's from the old kernel
231 >> . In case the new kernel contains a device that was not in the
old kernel
232 >> and a new, unused domain-id is actually needed, the bitmap will
give us on e.
233 >>
234 >> When a new domain is created for a device:
235 >> * If (this device has a context in the old kernel)
236 >> . Get domain-id, address-width, and IOVA ranges from the old
kernel context;
237 >> . Get address(page-entry-tables) from the copy in the new kernel;
238 >> . And apply all of the above values to the new domain structure.
239 >> * Else
240 >> . Create a new domain as normal
241 >>
242 >>
243 >> Bill Sumner (6):
244 >> Crashdump-Accepting-Active-IOMMU-Flags-and-Prototype
245 >> Crashdump-Accepting-Active-IOMMU-Utility-functions
246 >> Crashdump-Accepting-Active-IOMMU-Domain-Interfaces
247 >> Crashdump-Accepting-Active-IOMMU-Copy-Translations
248 >> Crashdump-Accepting-Active-IOMMU-Debug-Print-IOMMU
249 >> Crashdump-Accepting-Active-IOMMU-Call-From-Mainline
250 >>
251 >> drivers/iommu/intel-iommu.c | 1293
++++++++++++++++++++++++++++++++++++++++-- -
252 >> 1 file changed, 1225 insertions(+), 68 deletions(-)
253 >>
254 >
255 >
256 In summary:
257 1. We seem to agree that keeping the iommu active and using it is a
good idea.
258 And there are a few different ideas about how to use it. It will be
259 a good conversation to explore these and settle on a final solution.
260
261 2. Since the patches are currently available on a recent stable
baseline,
262 and the technique in them has already been somewhat tested by three
companies
263 and found to work, I would recommend completing the review, testing, and
264 implementation of these patches into the Linux kernel. They appear to
solve
265 the majority of the currently observed problems.
266
267 3. After that, exploration of other methodologies or extensions of these
268 patches could be pursued.
269
270 -- Bill
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu