Did you try to use the mtev driver? As I know, touch device should use mtev driver instead of evdev.
Regards, Esmond From: [email protected] [mailto:[email protected]] On Behalf Of Prabhuram Murugan Sent: Friday, September 06, 2013 10:39 AM To: Clark, Joel Cc: IVI Tizen Subject: Re: egalax touch screen not detected by X I extracted the binary file from TIZEN 1.0 rpm, xinput_calibrator --list No calibratable devices found. it is not able find any touch device. I think this is because it is detected as a mouse device . And the Xorg log file in /var/log/Xorg.0.log shows the below log, [ 10.434] (II) config/udev: Adding input device eGalax Inc. USB TouchController (/dev/input/mouse1) [ 10.434] (II) No input driver specified, ignoring this device. [ 10.434] (II) This device may have been added with another device file. I am wondering if the values in my Xorg configuration file is proper ? Section "InputClass" Identifier "eGalax Inc. USB TouchController" MatchIsPointer "on" MatchDevicePath "/dev/input/event*" Option "Calibration" "17 1000 27 1000" Driver "evdev" EndSection Jeol, it may sound stupid, Actually I launched a application and touched across the entire touch screen ... Screen was filled with buttons, but non of them received any click event... Regards, Prabhuram M On Fri, Sep 6, 2013 at 9:53 AM, Clark, Joel <[email protected]<mailto:[email protected]>> wrote: I’ll question my on assertion, Should evdev recognize a “single point, resistive touch screen device”, as a USB Mouse or as some other device? For multi-touch we know mouse did not work. But I think it also did not work for single touch, where when it was treated as a mouse, we could swipe (“drag” like a mouse), but could not tap (“click” like a mouse). Regards Joel From: Clark, Joel Sent: Thursday, September 05, 2013 5:46 PM To: Rees, Kevron M; Prabhuram Murugan Cc: IVI Tizen Subject: RE: egalax touch screen not detected by X It sounds like the same bug as in Wayland. It is being recognized as a USB device, but not as a touchscreen, so it defaults to being a mouse, which it is not. When you say “touch input is not working with this board”, what specifically is the failure mode? Does it respond to taps at all? Does it respond to “drag” at all? Regards Joel From: [email protected]<mailto:[email protected]> [mailto:[email protected]] On Behalf Of Rees, Kevron Sent: Thursday, September 05, 2013 5:41 PM To: Prabhuram Murugan Cc: IVI Tizen Subject: Re: egalax touch screen not detected by X it sounds like it is being recognized. perhaps it just needs calibration? I recall there is an xinput_calibrator tool that you might be able to use to calibrate it. I don't remember if that tool was included in Tizen 2.0 though. -Kevron On Thu, Sep 5, 2013 at 5:03 PM, Prabhuram Murugan <[email protected]<mailto:[email protected]>> wrote: Hi All, I am using TIZEN 2.0 ... Jeol, I gone through the changes, https://review.tizen.org/gerrit/#/c/6047/ , but it is for Weston and TIZEN 3.0 however to fix this issues in TIZEN 2.0, I am looking in to adaptation/xorg/driver/xserver-xorg-input-evdev can you advice, if this is the right point to start , Rusty, Yes, we are using a single point, resistive touch screen device. and from the mount point /dev/input/mouse1 looks it is detected as the mouse device. TIZEN 2.0 doesnt support single touch device ? On Fri, Sep 6, 2013 at 2:52 AM, Abramski, Adam M <[email protected]<mailto:[email protected]>> wrote: I believe he mentions below that he's running 2.0, NOT 3.0. Adam -----Original Message----- From: [email protected]<mailto:[email protected]> [mailto:[email protected]<mailto:[email protected]>] On Behalf Of Rusty Lynch Sent: Thursday, September 05, 2013 8:58 AM To: Clark, Joel Cc: IVI Tizen Subject: Re: egalax touch screen not detected by X Actually... that fix only applies when you are using wayland. I'm not sure if you were using a touchscreen with the same issue, but we hit an issue when a vendor wired up an old style single point resistive screen on top of an egalax touchscreen controller, where weston didn't recognize the device as touch (since it didn't support the modern multipoint protocol), and treated it as a mouse, but then the device would emit TOUCH_BTN instead of a left or right mouse button. So... it actually worked, but no software is listening for this little known button value so kind of pointless. --rusty On Thu, 2013-09-05 at 14:21 +0000, Clark, Joel wrote: > This has been fixed in Tizen IVI 3.0 > https://bugs.tizen.org/jira/i#browse/TIVI-1086 > > > > You might want to look at these patches: > > https://bugs.freedesktop.org/show_bug.cgi?id=54428 > > > > https://review.tizen.org/gerrit/#/c/6047/ > > > > with the fix the touchscreen is no longer recognized as a mouse > device. > > > > Regards > > Joel > > > > > > From: [email protected]<mailto:[email protected]> > [mailto:[email protected]<mailto:[email protected]>] > On Behalf Of Prabhuram Murugan > Sent: Thursday, September 05, 2013 5:38 AM > To: IVI Tizen > Subject: egalax touch screen not detected by X > > > > Hi , > > > I am using a USB based touch screen LCD for TIZEN on NDiS 166 board. > > > But the touch input is not working with this board. > I came across many bugs raised in TIZEN bug site, but they are mostly > for touch calibration. > > > In my case the touch screen is detected by the kernel but "xinput > list" doesnt list my touch screen device at all. Below are dmesg and > xinput list logs .... > > > I am using TIZEN 2.0 release. > > > > > > DMESG > > > [ 12.703678] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready > [ 21.528514] composite sync not supported > [ 884.484925] usb 2-1.1: USB disconnect, device number 3 [ > 885.940235] usb 2-1.1: new low-speed USB device number 7 using > ehci-pci [ 886.020179] usb 2-1.1: New USB device found, > idVendor=0eef, > idProduct=0001 > [ 886.020184] usb 2-1.1: New USB device strings: Mfr=1, Product=2, > SerialNumber=0 > [ 886.020188] usb 2-1.1: Product: USB TouchController [ 886.020191] > usb 2-1.1: Manufacturer: eGalax Inc. > [ 886.022735] input: eGalax Inc. USB TouchController as > /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input9 > > -sh-4.1# xinput list > ⎡ Virtual core pointer id=2 [master pointer > (3)] > ⎜ ↳ Virtual core XTEST pointer id=4 [slave > pointer (2)] > ⎜ ↳ SEJIN SEJIN USB Mini Trackball Keyboard id=11 [slave > pointer (2)] > ⎣ Virtual core keyboard id=3 [master keyboard > (2)] > ↳ Virtual core XTEST keyboard id=5 [slave > keyboard (3)] > ↳ SEJIN SEJIN USB Mini Trackball Keyboard id=10 [slave > keyboard (3)] > ∼ Power Button id=6 [floating slave] > ∼ Video Bus id=7 [floating slave] > ∼ Power Button id=8 [floating slave] > ∼ Microsoft LifeCam VX-800 id=9 [floating slave] > > #cat /dev/input/mouse1 > > )9 > > > > > Thanks and Regards, > Prabhuram M > > > _______________________________________________ > IVI mailing list > [email protected]<mailto:[email protected]> > https://lists.tizen.org/listinfo/ivi _______________________________________________ IVI mailing list [email protected]<mailto:[email protected]> https://lists.tizen.org/listinfo/ivi _______________________________________________ IVI mailing list [email protected]<mailto:[email protected]> https://lists.tizen.org/listinfo/ivi _______________________________________________ IVI mailing list [email protected]<mailto:[email protected]> https://lists.tizen.org/listinfo/ivi
_______________________________________________ IVI mailing list [email protected] https://lists.tizen.org/listinfo/ivi
