I tracked the problem down to be a ivtv problem. When using wintv2000 the television reports S-Video. When hot-rebooting from windows to linux I also have S-Video. The first call to ivtvctl -l 2 and or -l 0 the picture shows a vertical pattern. Calling -l 1 the picture gets black. Afterwards setting -l 2 or -l 0 returns the picture in Composite.
Definitely the supplied 9-pin to scart only supports Composite. The supplied 9-pin to S-Video/(Composite)/L/R works for S-Video. More information can be found in my previous post below. Using 2.6.16-1.2108_FC4, Packages from Atrpms. ivtv.i386 1:0.6.2-110.rhfc4.at installed ivtv-firmware.noarch 2:1.8a-9.at installed ivtv-firmware-audio.noarch 0.0.1-5.at installed ivtv-firmware-dec.noarch 2.02.023-9.at installed ivtv-firmware-enc.noarch 2.04.024-9.at installed ivtv-kernheaders.i386 1:0.6.2-110.rhfc4.at installed ivtv-kmdl-2.6.15-1.1831_FC4.i686 1:0.4.2-101.rhfc4.at installed (not used) ivtv-kmdl-2.6.16-1.2108_FC4.i686 1:0.6.2-110.rhfc4.at installed ivtv_xdriver.i386 0.10.6-3.rhfc4.at installed --------- /etc/modprobe.conf: alias char-major-81-0 ivtv alias char-major-81-1 ivtv alias char-major-81-2 ivtv alias char-major-61 lirc_i2c alias char-major-81 ivtv install lirc_i2c /sbin/modprobe ivtv; /sbin/modprobe --ignore-install lirc_i2c install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb ----------- in /etc/rc.local /sbin/modprobe lirc_i2c ----------- Are there other settings to try ? During the last two years I saw about 5 posts complaining about failing s-video support without any success. Is there anything I can do to narrow down the problem ? Regards Pascal ----- Original Message ----- From: "Pascal Favre" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Saturday, 13. May 2006 17:31 Subject: [ivtv-devel] PVR 350 - does provided 9-pin to scart cable supports-video > Hello > > Does the provided 9-pin to scart cable support s-video ? > I tried during the last 2 years, starting from 0.3 releases, 0.4.2, up to the > today installed 0.6.2 release. My TVs (just bought a new one) always reported > they received a CVBS (composite) signal. > > Changing with ivtvctl -l: > 0 (comp+s-video) television finds CVBS > 1 (comp) television is black > 2 (s-video) television finds CVBS > > Why is it that when changed explicitly to composite I get a black picture. > When changing to s-video the television reports CVBS ? > > I checked the scart cable. The scart side supports all leads to allow s-video > and composite (connected are 21,19,17(linked with 21),15,3,1,20,6,4,2) > http://utopia.knoware.nl/users/eprebel/SoundAndVision/Engineering/SCART.html > > After reading the pinout in the Wiki > http://ivtv.writeme.ch/tiki-index.php?page=PVR350_9DINPinout > I noticed that the luminance is not connected (to pin 19=luminance). Is this > the reason s-video with the provided scart cable does not work ? > > > How about the other provided cable, 9-ping to s-video, composite and L/R > sound. Can I use this adaptercable to connect to an appropriate scart cable > to get s-video (connecting s-video and L/R), or will my television still > report it receives composite ? > > On the users-list I found a similar post from 21.04.2006 from hans updating > to 0.4.5 (this should be equal to my 0.6.2 or not?): > http://www.gossamer-threads.com/lists/ivtv/users/29575?search_string=No%20TV-out%20S-video%20on%20PVR-350%20%28Pundit-R%20350%29%20%20;#29575 > -- > It fixes a nasty bug in the initialization of the saa7129 chip > responsible for TV-out. There is a possibility that this is not the > reason for your problems, but it is certainly the first thing to try. > I'll probably make an ivtv-0.4.5 release this or next weekend which will > contain this fix. > -- > > Any help very much appreciated. > Pascal > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.6.2 (development snapshot compiled on Mon May 8 07:44:41 > 2006) loading > ivtv: Linux version: 2.6.16-1.2108_FC4 686 REGPARM 4KSTACKS gcc-4.0 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based) > ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 16 (level, low) -> IRQ 193 > tveeprom 0-0050: Hauppauge model 48139, rev K257, serial# 7805538 > tveeprom 0-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) > tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom > 0x74) > tveeprom 0-0050: audio processor is MSP4418 (idx 25) > tveeprom 0-0050: decoder processor is SAA7115 (idx 19) > tveeprom 0-0050: has radio, has IR remote > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > tda9887 0-0043: chip found @ 0x86 (ivtv i2c driver #0) > saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > eepro100.c:v1.09j-t 9/29/99 Donald Becker > http://www.scyld.com/network/eepro100.html > eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin > <[EMAIL PROTECTED]> and others > 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) > saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) > msp3400 0-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c driver #0) > msp3400 0-0040: MSP4418G-B3 supports nicam and radio, mode is autodetect and > autoselect > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > ivtv0: Encoder revision: 0x02040024 > ivtv0: Decoder revision: 0x02020023 > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) > ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) > ivtv0: Create encoder radio stream > ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total) > ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total) > ivtv0: Create decoder VOUT stream > ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total) > ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) > tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) > ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 > ivtv: ====================== NEXT CARD ====================== > ivtv1: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) > ACPI: PCI Interrupt 0000:06:08.0[A] -> GSI 21 (level, low) -> IRQ 201 > tuner 1-0060: TEA5767 detected. > tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #1) > tuner 1-0060: type set to 62 (Philips TEA5767HN FM Radio) > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1) > tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #1) > tveeprom 1-0050: Hauppauge model 23559, rev D591, serial# 8201932 > tveeprom 1-0050: tuner model is Philips FQ1216AME MK4 (idx 91, type 56) > tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom > 0x74) > tveeprom 1-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, > type 62) > tveeprom 1-0050: audio processor is CX25843 (idx 37) > tveeprom 1-0050: decoder processor is CX25843 (idx 30) > tveeprom 1-0050: has radio, has no IR remote > ivtv1: This is the first unit of a PVR500 > cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1) > cx25840 1-0044: loaded v4l-cx25840.fw firmware (13353 bytes) > wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1) > ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv1: Encoder revision: 0x02040024 > ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv1: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) > ivtv1: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) > ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) > ivtv1: Create encoder radio stream > tuner 1-0061: type set to 56 (Philips PAL/SECAM multi (FQ1216AME MK4)) > ivtv1: Initialized WinTV PVR 500 (unit #1), card #1 > ivtv: ====================== NEXT CARD ====================== > ivtv2: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) > ACPI: PCI Interrupt 0000:06:09.0[A] -> GSI 22 (level, low) -> IRQ 209 > tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #2) > tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #2) > cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #2) > cx25840 2-0044: loaded v4l-cx25840.fw firmware (13353 bytes) > wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #2) > tveeprom 2-0050: Hauppauge model 23559, rev D591, serial# 8201932 > tveeprom 2-0050: tuner model is Philips FQ1216AME MK4 (idx 91, type 56) > tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom > 0x74) > tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, > type 62) > tveeprom 2-0050: audio processor is CX25843 (idx 37) > tveeprom 2-0050: decoder processor is CX25843 (idx 30) > tveeprom 2-0050: has radio, has no IR remote > ivtv2: This is the second unit of a PVR500 > ivtv2: Correcting tveeprom data: no radio present on second unit > ivtv2: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv2: Encoder revision: 0x02040024 > ivtv2: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv2: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) > ivtv2: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) > ivtv2: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) > tuner 2-0061: type set to 56 (Philips PAL/SECAM multi (FQ1216AME MK4)) > ivtv2: Initialized WinTV PVR 500 (unit #2), card #2 > ivtv: ==================== END INIT IVTV ==================== > ivtv0-osd: Framebuffer module loaded (attached to ivtv card id 0) > ivtv0-osd: screen coords: [0 0] -> [720 576] > ivtv0-osd: original global alpha = 208 > ivtv0-osd: current OSD state = 39 > ivtv0-osd: new global alpha = 208 (1 255 0) > ivtv0-osd: framebuffer at 0xed510000, mapped to 0xe1010000, size 1665k > ivtv0-osd: mode is 720x576x32, linelength=2880 > ivtv0-osd warning: ivtvfb_set_par > Console: switching to colour frame buffer device 90x36 > ivtv0-osd: fb0: cx23415 TV out frame buffer device > ivtv0: Allocate DMA decoder OSD stream: 16 x 65536 buffers (1024KB total) > > > _______________________________________________ > ivtv-devel mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-devel > _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
