Hi, first time using IVTV but running into a bit of trouble...
dmesg tells me:
[17184358.872000] ivtv: ==================== START INIT IVTV
====================
[17184358.872000] ivtv: version 0.7.0 (tagged release) loading
[17184358.872000] ivtv: Linux version: 2.6.17-10-generic SMP mod_unload 586
REGPARM gcc-4.1
[17184358.872000] ivtv: In case of problems please include the debug info
between
[17184358.872000] ivtv: the START INIT IVTV and END INIT IVTV lines, along with
[17184358.872000] ivtv: any module options, when mailing the ivtv-users
mailinglist.
[17184358.876000] ivtv0: Unknown card: vendor/device: 4444/0016
[17184358.876000] ivtv0: subsystem vendor/device: 104d/813d
[17184358.876000] ivtv0: cx23416 based
[17184358.876000] ivtv0: Defaulting to Hauppauge WinTV PVR-150 card
[17184358.876000] ivtv0: Please mail the vendor/device and subsystem
vendor/device IDs and what kind of
[17184358.876000] ivtv0: card you have to the ivtv-devel mailinglist
(www.ivtvdriver.org)
[17184358.876000] ivtv0: Prefix your subject line with [UNKNOWN CARD].
[17184358.876000] ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 16 (level, low) ->
IRQ 177
[17184358.932000] tveeprom 0-0050: Encountered bad packet header [aa]. Corrupt
or not a Hauppauge eeprom.
[17184358.932000] ivtv0: No tuner detected, default to NTSC
[17184358.984000] tuner 0-0060: All bytes are equal. It is not a TEA5767
[17184358.984000] tuner 0-0060: chip found @ 0xc0 (ivtv i2c driver #0)
[17184359.856000] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
[17184360.072000] ivtv0: Encoder revision: 0x02050032
[17184360.072000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers
(4096KB total)
[17184360.072000] ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers
(2048KB total)
[17184360.072000] ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers
(2048KB total)
[17184360.076000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608
buffers (2048KB total)
[17184360.076000] tuner 0-0060: type set to 0 (Temic PAL (4002 FH5))
[17184360.076000] ivtv0: i2c hardware 0x00000001 not found for command
0xc008561c!
[17184360.076000] ivtv0: i2c addr 0x44 not found for command 0x4008646f!
[17184360.076000] ivtv0: i2c hardware 0x00000020 not found for command
0x4008646d!
[17184360.076000] ivtv0: i2c hardware 0x00000001 not found for command
0x4008646d!
[17184360.076000] ivtv0: i2c hardware 0x00000001 not found for command
0xc008561c!
[17184360.080000] ivtv0: i2c hardware 0x00000001 not found for command
0xc008561c!
[17184360.080000] ivtv0: i2c hardware 0x00000001 not found for command
0xc008561c!
[17184360.080000] ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
[17184360.080000] ivtv: ==================== END INIT IVTV
====================
and according to lspci -vv:
05:04.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416)
MPEG-2 Encoder (rev 01)
Subsystem: Sony Corporation Unknown device 813d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 177
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Thanks!
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
