On Saturday 02 December 2006 20:55, Nuno Oliveira wrote:
> Hey,
>
> Similarly to what Martin Dauskardt ([EMAIL PROTECTED]) reported on Nov 19,
> I also get a lot of these errors
>
> ivtv0: i2c addr 0x21 not found for command 0xc0445624!
> last message repeated 3 times
>
> with a PVR-350 board, using 2.6.19 and ivtv-0.9.0. I can't get the
> card to work with these versions, although it works perfectly with
> 2.6.18 and ivtv-0.8.0.
>
> The kernel startup log follows. In the init phase there are already a
> number of these errors. Any ideas?
Please add the following to the /etc/modprobe.conf file and try again:
options saa7115 debug=1
Post the same log again, it should now contain some saa7115 debugging.
Thanks,
Hans
>
> Thanks,
>
> Nuno.
>
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.9.0 (tagged release) loading
> ivtv: Linux version: 2.6.19 SMP preempt PENTIUM4
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected Hauppauge card (cx23415 based)
> ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
> Dec 2 15:39:09 yucca kernel: input: i2c IR (Hauppauge) as
> /class/input/input3 ir-kbd-i2c: i2c IR (Hauppauge) detected at
> i2c-3/3-0018/ir0 [ivtv i2c driver #0] i2c_adapter i2c-3: Client
> creation failed at 0x40 (-5)
> msp3400 3-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c driver #0)
> msp3400 3-0040: MSP4418G-B3 supports nicam and radio, mode is
> autodetect and autoselect i2c_adapter i2c-3: Client creation failed
> at 0x44 (-1)
> tuner 3-0043: chip found @ 0x86 (ivtv i2c driver #0)
> tda9887 3-0043: tda988[5/6/7] found @ 0x43 (tuner)
> tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> tveeprom 3-0050: Hauppauge model 48139, rev K257, serial# 2979907
> tveeprom 3-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type
> 38) tveeprom 3-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L')
> PAL(D/D1/K) (eeprom 0x74) tveeprom 3-0050: audio processor is MSP4418
> (idx 25)
> tveeprom 3-0050: decoder processor is SAA7115 (idx 19)
> tveeprom 3-0050: has radio, has IR remote
> ivtv0: Autodetected Hauppauge WinTV PVR-350
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Decoder revision: 0x02020023
> ivtv0: Registered device video0 for encoder MPEG
> ivtv0: Registered device video32 for encoder YUV
> ivtv0: Registered device vbi0 for encoder VBI
> ivtv0: Registered device video24 for encoder PCM audio
> ivtv0: Registered device radio0 for encoder radio
> ivtv0: Registered device video16 for decoder MPEG
> ivtv0: Registered device vbi8 for decoder VBI
> ivtv0: Registered device vbi16 for decoder VOUT
> ivtv0: Registered device video48 for decoder YUV
> ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
> tuner 3-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
> ivtv0: i2c addr 0x21 not found for command 0x4008646f!
> ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
> ivtv: ==================== END INIT IVTV ====================
>
> _______________________________________________
> ivtv-devel mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
