Hans Verkuil wrote: > On Friday 18 May 2007 19:59, Stefan Langeland wrote: >> Hans Verkuil wrote: >> > <snip> >>> - Add autodetect for new PVR150 low-profile models. >>> >> > <snip> >> >> Hi Hans, >> >> I just had a quick look on the sourcecode (ivtv-driver.c) and I have >> to tell you, that although it is called PVR150 low profile, it uses >> the same driver as for the 250. So the id's should be moved up in the >> sourcecode to the 250er section (at least I am using with my low >> profile the drivers of the 250). >> >> If I find some spare time I will test the 0.10.2, but I don't think >> it will work for me. But perhaps you changed something somewhere else >> where I didn't look then forgive me :) > > Ouch, I understood that it was a PVR150. Can you check the latest ivtv > on the 0.10 branch? You can get it here: > > http://ivtvdriver.org/viewcvs/ivtv/branches/0.10.tar.gz?view=tar > > Let me know if that one works alright. > > Thanks, > > Hans > Hi Hans,
The version is working (see below). Just to make it clear: Hauppauge is only selling 150 low profile, and my card is a 150 low profile. But my card has to be used with the 250 driver. I don't know why hauppauge is doing this. Thanks for changing the driver :) Stefan [ 839.815169] ivtv: ==================== START INIT IVTV ==================== [ 839.815177] ivtv: version 0.10.3 (development snapshot compiled on Sa 19 Mai 2007 09:33:18 CEST) loading [ 839.815180] ivtv: Linux version: 2.6.20-15-generic SMP mod_unload 586 [ 839.815182] ivtv: In case of problems please include the debug info between [ 839.815185] ivtv: the START INIT IVTV and END INIT IVTV lines, along with [ 839.815187] ivtv: any module options, when mailing the ivtv-users mailinglist. [ 839.816318] ivtv0: Autodetected Hauppauge card (cx23416 based) [ 839.816465] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 19 [ 840.462424] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) [ 840.677723] ivtv0: Encoder revision: 0x02050032 [ 840.677726] ivtv0: Recommended firmware version is 0x02060039. [ 840.747202] tveeprom 0-0050: Hauppauge model 30039, rev B157, serial# 6817533 [ 840.747211] tveeprom 0-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) [ 840.747215] tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) [ 840.747219] tveeprom 0-0050: audio processor is MSP4418 (idx 25) [ 840.747222] tveeprom 0-0050: decoder processor is SAA7115 (idx 19) [ 840.747225] tveeprom 0-0050: has radio, has no IR receiver, has no IR transmitter [ 840.747228] ivtv0: Autodetected Hauppauge WinTV PVR-250 [ 840.761052] tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) [ 840.761093] tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) [ 840.765453] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) [ 840.832888] saa7115 0-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0) [ 841.025146] msp3400 0-0040: MSP4418G-A2 found @ 0x80 (ivtv i2c driver #0) [ 841.025153] msp3400 0-0040: MSP4418G-A2 supports nicam and radio, mode is autodetect and autoselect [ 841.027134] ivtv0: Registered device video0 for encoder MPEG (4 MB) [ 841.027519] ivtv0: Registered device video32 for encoder YUV (2 MB) [ 841.027872] ivtv0: Registered device vbi0 for encoder VBI (1 MB) [ 841.028052] ivtv0: Registered device video24 for encoder PCM audio (1 MB) [ 841.028446] ivtv0: Registered device radio0 for encoder radio [ 841.028559] tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) [ 841.465572] ivtv0: Initialized Hauppauge WinTV PVR-250, card #0 [ 841.465694] ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
