Hi!
I'm using a Hauppauge PVR 150 with remote. The card works fine with the
tuner patch, but in the channels.conf (vdr) I have to set all frequencies
7MHz lower as they physically are. But this is not why I'm writing.
It's that the remote only works, when I previously booted Windows XP MCE2005
with original Hauppauge drivers from a secound HD and then rebooted with my
debian 2.4.27-ctvdr-1 vdr system. After rebooting from Win XP I see echos
from irw, but when I do a cold boot I get a connection refuse.
Here I have posted the two ivtv extracts for both variants:
after a cold boot:
i2c-core.o: driver i2c ir driver registered.
i2c-core.o: driver cx25840 registered.
cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005)
after rebooting from Windows XP:
i2c-core.o: driver i2c ir driver registered.
lirc_i2c: chip found @ 0x71 (Hauppauge IR (PVR150))
ivtv: i2c attach [client=Hauppauge IR (PVR150),ok]
i2c-core.o: client [Hauppauge IR (PVR150)] registered to adapter [ivtv i2c
driver #0](pos. 2).
lirc_dev: lirc_register_plugin:sample_rate: 10
i2c-core.o: driver cx25840 registered.
cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005)
I tried different ivtv versions and tried to load the modules i2c-dev,
lirc_i2c and ivtv in different orders, but with no success.
I'm free for any sugestions that might help me.
Here my ivtv debug after a cold boot:
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-core.o: driver i2c TV tuner driver registered.
Linux video capture interface: v1.00
i2c-algo-bit.o: i2c bit algorithm module
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.4 (o) loading
ivtv: Linux version: 2.4.27-ctvdr-1
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 150 card
ivtv: Found an iTVC16 based chip
PCI: Found IRQ 3 for device 00:0b.0
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x7190 vendor: 0x8086
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
i2c-core.o: client [(tuner unset)] registered to adapter [ivtv i2c driver
#0](pos. 0).
i2c-core.o: adapter ivtv i2c driver #0 registered as adapter 0.
i2c-core.o: driver tveeprom registered.
tveeprom: Hauppauge: model = 26034, rev = C197, serial# = 7703309
tveeprom: tuner = LG PAL (TAPE Series) (idx = 97, type = 55)
tveeprom: tuner fmt = PAL(B/G) PAL(D/K) (eeprom = 0x44, v4l2 = 0x00000e07)
tveeprom: audio_processor = MSP3400C (type = 4)
ivtv: i2c attach [client=tveeprom[32],ok]
i2c-core.o: client [tveeprom[32]] registered to adapter [ivtv i2c driver
#0](pos. 1).
ivtv: Tuner Type 55, Tuner formats 0x00000e07, Radio: yes, Model 0x008d1657,
Revision 0x00000000
ivtv: PAL tuner detected
ivtv: Radio detected
lirc_dev: IR Remote Control driver registered, at major 61
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Host bridge needs ETBF enabled.
i2c-core.o: driver i2c ir driver registered.
i2c-core.o: driver cx25840 registered.
cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005)
cx25840: detecting client on address 0x88
cx25840: writing init values
cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded.
cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa
cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6
cx25840: Status: cx258423 (DEVICE_ID)
ivtv: i2c attach [client=cx25840[32],ok]
i2c-core.o: client [cx25840[32]] registered to adapter [ivtv i2c driver
#0](pos. 2).
i2c-core.o: driver wm8775 registered.
ivtv: i2c attach [client=wm8775[32],ok]
i2c-core.o: client [wm8775[32]] registered to adapter [ivtv i2c driver
#0](pos. 3).
ivtv: Encoder revision: 0x02040011
ivtv: Configuring WinTV PVR 150 card with 5 streams
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 0 using 128 16384 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create DMA stream 1 using 20 103680 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 2 using 60 34632 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Create stream 4
ivtv: Setting Tuner 50
tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0
cx25840: decoder set input (6)
cx25840: Tuner Input
ivtv: Switching standard to PAL.
cx25840: decoder set norm PAL
ivtv: Initialized WinTV PVR 150, card #0
ivtv: ==================== END INIT IVTV ====================
ivtv: ivtv_enc_thread: pid = 178, itv = 0xd488f440
device-mapper: 4.1.1-ioctl (2004-04-07) initialised: [EMAIL PROTECTED]
-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click
_______________________________________________
ivtv-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/ivtv-devel
