Thanks...
ivtv: i2c client addr: 0x21 not found for command 0x40046403!
ivtv: i2c client addr: 0x21 not found for command 0x40046404!
ivtv: Setting audio matrix to input 3, output 1
ivtv: i2c client addr: 0x40 not found for command 0x40086d11!
ivtv: i2c client addr: 0x40 not found for command 0x80287610!
ivtv: i2c client addr: 0x40 not found for command 0x40287611!
ivtv: Switching standard to NTSC.
ivtv: i2c client addr: 0x40 not found for command 0x40307603!
ivtv: i2c client addr: 0x21 not found for command 0x40046403!
ivtv: Initialized WinTV PVR 250, card #0
Humm....you have a 150 but it sees a 250. I'm assuming that you have
only tried this doing modprobes, etc. For kicks maybe try a COLD boot.
Set up modprobe.conf (or local.start, etc.) to load these drivers,
then power down and boot up again.
Yes, with 0.3.x I've always had it think it's a 250. I've never been able to
get 0.3.x to recognize the card as a 150, even though 0.2 does successfully
recognize it as 150.
I loaded the modules manually, after a reboot (power down, turn off,
reboot). It still thinks it's a 250. I get video fine, but no audio. With
0.2 I get b&w video, and audio is fine.
I'm currently only loading modules manually via modprobe. How do I do it via
modprobe.conf?
application mixer_applet2 uses obsolete OSS audio interface
cx25840: no version for "struct_module" found: kernel tainted.
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.6 (w) loading
ivtv: Linux version: 2.6.12-1.1390_FC4smp SMP 686 REGPARM 4KSTACKS gcc-4.0
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Unknown card: vendor/device: 4444/0016, subsystem vendor/device:
0000/8801
ivtv: Defaulting to WinTV PVR 250 card
ivtv: Please mail the vendor/device and subsystem vendor/device IDs and what
kind of
ivtv: card you have to the ivtv-devel mailinglist:
http://sourceforge.net/projects/ivtv
ivtv: Prefix your subject line with [UNKNOWN CARD].
ivtv: Found an iTVC16 based chip
ivtv: XXX PCI device: 0x7190 vendor: 0x8086
ivtv: i2c attach [client=tveeprom,ok]
cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005)
cx25840: detecting cx25840 client on address 0x88
cx25840: cx25843-23 found. Initializing...
cx25840: requesting /lib/modules/HcwMakoA.ROM
cx25840: firmware loaded
ivtv: i2c attach [client=cx25840[50],ok]
tveeprom: Hauppauge: model = 26552, rev = B268, serial# = 7865176
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3410D (type = 5)
ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model 0x00892598,
Revision 0xc031b9eb
ivtv: NTSC tuner detected
ivtv: Radio detected
ivtv: i2c attach [client=(tuner unset),ok]
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
saa7115: starting probe for adapter SMBus PIIX4 adapter at 0440 (0x0)
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
ivtv: Encoder revision: 0x02050032
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 250 card with 5 streams
ivtv: Registered v4l2 device for encoder MPEG minor 0
ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
ivtv: Registered v4l2 device for encoder YUV minor 32
ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
ivtv: Registered v4l2 device for encoder VBI minor 224
ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
ivtv: Registered v4l2 device for encoder PCM audio minor 24
ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
ivtv: Registered v4l2 device for encoder radio minor 64
ivtv: Create encoder radio stream
ivtv: Setting Tuner 47
tuner 1-0061: type set to 47 (LG NTSC (TAPE series))
ivtv: i2c client addr: 0x21 not found for command 0x40046403!
ivtv: i2c client addr: 0x21 not found for command 0x40046404!
ivtv: Setting audio matrix to input 3, output 1
ivtv: i2c client addr: 0x40 not found for command 0x40086d11!
ivtv: i2c client addr: 0x40 not found for command 0x80287610!
ivtv: i2c client addr: 0x40 not found for command 0x40287611!
ivtv: Switching standard to NTSC.
ivtv: i2c client addr: 0x40 not found for command 0x40307603!
ivtv: i2c client addr: 0x21 not found for command 0x40046403!
ivtv: Initialized WinTV PVR 250, card #0
ivtv: ==================== END INIT IVTV ====================
ivtv: ivtv_enc_thread: pid = 2822, itv = 0xe8b72120
ivtv: ivtv_enc_vbi_thread: pid = 2823, itv = 0xe8b72120
-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click
_______________________________________________
ivtv-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/ivtv-devel
