That's what I was afraid of: unsupported tuner. I'll enquire on the dev list to see what the status is.
[EMAIL PROTECTED] wrote: > I just got the same kind of tuner myself (though I think mine is a > PVR-150MCE), and I have the same issue with ivtv version 0.4.2 (tuner = 4, No > Tuner). I have the same exact tuner listed in dmesg: TCL MFNM05-4. I tried > changing the tuner type in the module options, and got some signals using 53, > but the lower channels would not come in and the channel list was off by two. > So maybe we need to wait until this is supported in a newer version? > >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> > Running gentoo Linux, 2.6.13-gentoo-r3 with ivtv 0.4.0 > I've been running fine with a single pvr350 card and I just added a pvr150 > as a second tuner. The 350 continues to work fine, but the 150 only gives > static. It's not normal static, because it's full of multi-coloured > stripes. ivtvctrl also shows the card as muted and I can't change it. I > did try gabbing the latest firmware, but it made no difference. > > The only things that looks strange is the following kernel message: > tuner: type set to 4 (NoTuner) by ivtv i2c driver #0 > > Any help is greatly appriciated. > > > Linux video capture interface: v1.00 > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.4.0 (tagged release) loading > ivtv: Linux version: 2.6.13-gentoo-r3 preempt PENTIUMIII gcc-3.3 > ivtv: In case of problems please include the debug info > ivtv: between the START INIT IVTV and END INIT IVTV lines when > ivtv: mailing the ivtv-devel mailinglist. > ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based) > PCI: Found IRQ 9 for device 0000:02:09.0 > PCI: Sharing IRQ 9 with 0000:01:00.0 > PCI: Sharing IRQ 9 with 0000:02:0b.0 > tveeprom: ivtv version > tveeprom: Hauppauge: model = 26552, rev = F0A3, serial# = 8919104 > tveeprom: tuner = TCL MFNM05-4 (idx = 103, type = 4) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > tveeprom: audio processor = CX25843 (type = 25) > tveeprom: decoder processor = CX25843 (type = 1e) > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] > cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) > cx25840 0-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes) > ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] > wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] > tda9885/6/7: (ivtv) chip found @ 0x86 > ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] > ivtv0: loading /lib/modules/ivtv-fw-enc.bin > ivtv0: Encoder revision: 0x02050032 > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) > ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) > ivtv0: Create encoder radio stream > tuner: type set to 4 (NoTuner) by ivtv i2c driver #0 > ivtv0: Initialized WinTV PVR 150, card #0 > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users > -- DS _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
