On Jun 29, 2006, at 3:01 PM, Kenneth Hester wrote: > Keith C, > > It looks like both cards say they are the second tuner on a PVR 500. > > Do you know the "normal" ivtv messages for a PVR 500 MCE?
You could find some in the archives. I know mine are posted there many times. > > I have tried many combinations of the alias char-major-81 and none > seem to make any difference. For the > alias char-major-81 line I have tried off, ivtv, and videodev. > I just tried: > alias char-major-81 ivtv > alias char-major-81-0 ivtv > alias char-major-81-1 ivtv > > and then > alias char-major-81 videodev > alias char-major-81-0 ivtv > alias char-major-81-1 ivtv > > with very similar dmesg output and the same quality results. > > I may post this to the ivtv-devel list since the driver says: > ivtv1: Unknown card: vendor/device: 4444/0016 > ivtv1: subsystem vendor/device: 0070/b7f7 > ivtv1: cx23416 based > ivtv1: Defaulting to Hauppauge WinTV PVR-150 card > ivtv1: Please mail the vendor/device and subsystem vendor/device > ivtv1: Please mail the vendor/device and subsystem vendor/device > IDs and > what kind of > ivtv1: card you have to the ivtv-devel mailinglist Yeah, thats bad. Post it there and someone will either let you know what version of ivtv will add support for it, or they'll give you an existing tuner # to try. Keith C > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Keith C > Sent: Thursday, June 29, 2006 2:11 PM > To: User discussion about IVTV > Subject: Re: [ivtv-users] Any Luck with PVR 500 MCE on Suse 10.1 > > > On Jun 29, 2006, at 1:27 PM, Kenneth Hester wrote: > >> I can't seem to get my PVR 500 MCE to work. I have tried several >> distributions >> and ivtv versions. Has anyone had any success with this? >> >> The driver also reports that it doesn't recognize the second unit >> on the >> card. >> Is this normal? Right after that it says it is the 2nd unit on a >> 500. >> >> It was purchased from Dell. >> It is a PVR 500 MCE with and FM receiver and no remote on the card. >> >> The first tuner works slightly. It has complete snow on the lower >> channels >> and slight snow on the upper channels. I am in the US on cable and >> the >> frequencies appear to be correct (2=55.250, 75=529.250). The >> sound is >> always good on all channels. I am running SUSE 10.1 with >> ivtv-0.6.3 with >> suse built kernel 2.6.16.13-default >> I have also tried 0.6.2 on SUSE 10.1 and 0.4.2 on SUSE 10.0 and the >> KnoppMyth distribution with the same results. The card appears to >> work properly under Windoze. >> >> The second tuner does not work. >> In modprobe.conf I have these lines: >> alias char-major-81-0 off >> alias char-major-81-1 ivtv >> alias char-major-81-2 ivtv > > What's up with the "off" line? I'm not sure that will work. If > you're trying to force the PVR-500 onto video1 and video2, do this : > > alias char-major-81 ivtv > alias char-major-81-1 ivtv > alias char-major-81-2 ivtv > options ivtv ivtv_first_minor=1 > > If you look through the dmesg output, you'll see that the first card > detected is the second unit of the PVR-500, not the first. > > Keith C > >> >> lspci -v shows the cards as below. I included the sound card >> because it >> seems to share the same IRQ >> as the second tuner: >> 00:1f.5 Multimedia audio controller: Intel Corporation 82801AA >> AC'97 Audio >> (rev 02) >> Subsystem: Unknown device 4352:5933 >> Flags: bus master, medium devsel, latency 0, IRQ 10 >> I/O ports at 1200 [size=256] >> I/O ports at 1300 [size=64] >> >> 02:08.0 Multimedia video controller: Internext Compression Inc iTVC16 >> (CX23416) MPEG-2 Encoder (rev 01) >> Subsystem: Hauppauge computer works Inc. WinTV PVR 500 (1st unit) >> Flags: bus master, medium devsel, latency 64, IRQ 11 >> Memory at f4000000 (32-bit, prefetchable) [size=64M] >> Capabilities: [44] Power Management version 2 >> >> 02:09.0 Multimedia video controller: Internext Compression Inc iTVC16 >> (CX23416) MPEG-2 Encoder (rev 01) >> Subsystem: Hauppauge computer works Inc. WinTV PVR 500 (2nd unit) >> Flags: bus master, medium devsel, latency 64, IRQ 10 >> Memory at f8000000 (32-bit, prefetchable) [size=64M] >> Capabilities: [44] Power Management version 2 >> >> I am running the current firmware: >> 305dba74bbe5905447add8883f3ecb68 v4l-cx2341x-dec.fw >> 5f5fa240ada73c3565f5f7de4c7b5138 v4l-cx2341x-enc.fw >> 99836e41ccb28c7b373e87686f93712a v4l-cx25840.fw >> >> The v4l-cx2341x-enc.fw also matches the CD shipped by Hauppauge >> with the >> card. >> >> >> ivtv: ==================== START INIT IVTV ==================== >> ivtv: version 0.6.3 (tagged release) loading >> ivtv: Linux version: 2.6.16.13-4-default 586 REGPARM gcc-4.1 >> ivtv: In case of problems please include the debug info between >> ivtv: the START INIT IVTV and END INIT IVTV lines, along with >> ivtv: any module options, when mailing the ivtv-users mailinglist. >> ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) >> tveeprom 0-0050: Hauppauge model 23552, rev D487, serial# 9525425 >> tveeprom 0-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type >> 70) >> tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) >> tveeprom 0-0050: second tuner model is Philips TEA5768HL FM Radio >> (idx 101, >> type 62) >> tveeprom 0-0050: audio processor is CX25843 (idx 37) >> tveeprom 0-0050: decoder processor is CX25843 (idx 30) >> tveeprom 0-0050: has radio, has no IR remote >> ivtv0: This is the second unit of a PVR500 >> ivtv0: Correcting tveeprom data: no radio present on second unit >> usbcore: registered new driver usbfs >> usbcore: registered new driver hub >> USB Universal Host Controller Interface driver v2.3 >> PCI: Found IRQ 9 for device 0000:00:1f.2 >> PCI: Setting latency timer of device 0000:00:1f.2 to 64 >> uhci_hcd 0000:00:1f.2: UHCI Host Controller >> uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1 >> uhci_hcd 0000:00:1f.2: irq 9, io base 0x00001820 >> usb usb1: new device found, idVendor=0000, idProduct=0000 >> usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 >> usb usb1: Product: UHCI Host Controller >> usb usb1: Manufacturer: Linux 2.6.16.13-4-default uhci_hcd >> usb usb1: SerialNumber: 0000:00:1f.2 >> usb usb1: configuration #1 chosen from 1 choice >> hub 1-0:1.0: USB hub found >> hub 1-0:1.0: 2 ports detected >> tuner 0-0060: TEA5767 detected. >> tuner 0-0060: chip found @ 0xc0 (ivtv i2c driver #0) >> tuner 0-0060: type set to 62 (Philips TEA5767HN FM Radio) >> tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) >> cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) >> i810_smbus 0000:00:01.0: i810/i815 i2c device found. >> i2c-algo-bit.o: (0) scl=1, sda=1 >> i2c-algo-bit.o: (1) scl=1, sda=0 >> i2c-algo-bit.o: (2) scl=1, sda=1 >> i2c-algo-bit.o: (3) scl=0, sda=1 >> i2c-algo-bit.o: (4) scl=1, sda=1 >> i2c-algo-bit.o: I810/I815 I2C Adapter passed test. >> usb 1-1: new full speed USB device using uhci_hcd and address 2 >> Linux agpgart interface v0.101 (c) Dave Jones >> usb 1-1: new device found, idVendor=0609, idProduct=031d >> usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3 >> usb 1-1: Product: eHome Infrared Transceiver >> usb 1-1: Manufacturer: SMK >> usb 1-1: SerialNumber: SM0059g4 >> usb 1-1: configuration #1 chosen from 1 choice >> i8xx TCO timer: initialized (0x1060). heartbeat=30 sec (nowayout=0) >> hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33) >> Uniform CD-ROM driver Revision: 3.20 >> JBD: barrier-based sync failed on hda3 - disabling barriers >> cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes) >> i2c-algo-bit.o: (0) scl=1, sda=1 >> i2c-algo-bit.o: (1) scl=1, sda=0 >> i2c-algo-bit.o: (2) scl=1, sda=1 >> i2c-algo-bit.o: (3) scl=0, sda=1 >> i2c-algo-bit.o: (4) scl=1, sda=1 >> i2c-algo-bit.o: I810/I815 DDC Adapter passed test. >> agpgart: Detected an Intel i810 Chipset. >> agpgart: AGP aperture is 64M @ 0xf0000000 >> wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) >> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) >> ivtv0: Encoder revision: 0x02050032 >> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers >> (4096KB total) >> ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB >> total) >> ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB >> total) >> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers >> (2048KB >> total) >> tuner 0-0061: type set to 70 (Samsung TCPN 2121P30A) >> ivtv0: Initialized WinTV PVR 500 (unit #2), card #0 >> ivtv: ====================== NEXT CARD ====================== >> ivtv1: Unknown card: vendor/device: 4444/0016 >> ivtv1: subsystem vendor/device: 0070/b7f7 >> ivtv1: cx23416 based >> ivtv1: Defaulting to Hauppauge WinTV PVR-150 card >> ivtv1: Please mail the vendor/device and subsystem vendor/device >> IDs and >> what kind of >> ivtv1: card you have to the ivtv-devel mailinglist >> (www.ivtvdriver.org) >> ivtv1: Prefix your subject line with [UNKNOWN CARD]. >> tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1) >> cx25840 3-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1) >> cx25840 3-0044: loaded v4l-cx25840.fw firmware (16382 bytes) >> wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #1) >> tveeprom 3-0050: Hauppauge model 23552, rev D487, serial# 9525425 >> tveeprom 3-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type >> 70) >> tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08) >> tveeprom 3-0050: second tuner model is Philips TEA5768HL FM Radio >> (idx 101, >> type 62) >> tveeprom 3-0050: audio processor is CX25843 (idx 37) >> tveeprom 3-0050: decoder processor is CX25843 (idx 30) >> tveeprom 3-0050: has radio, has no IR remote >> ivtv1: This is the second unit of a PVR500 >> ivtv1: Correcting tveeprom data: no radio present on second unit >> ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) >> ivtv1 warning: Encoder mailbox not found >> ivtv1 warning: Decoder mailbox not found >> ivtv1: Error locating firmware. >> ivtv1: Error -12 on initialization >> ivtv: probe of 0000:02:09.0 failed with error -12 >> ivtv: ==================== END INIT IVTV ==================== >> >> >> _______________________________________________ >> ivtv-users mailing list >> [email protected] >> http://ivtvdriver.org/mailman/listinfo/ivtv-users > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
