Greetings,
I'm having an odd issue with a PVR-150. I have 2 and the both were
working fine until I tried testing a pci video card, since then
(despite manual and automatic IRQ reassignments) the second card comes
up with this error:
ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command
0xc008561c!
Here's my dmesg with the ivtv part - note the second card doesn't seem
to be detecting and loading 'cx25840' like the first card (ivtv0) is
doing:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.10.1 (tagged release) loading
ivtv: Linux version: 2.6.20-1.2944.fc6 SMP mod_unload 686 4KSTACKS
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 18
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
8139too Fast Ethernet driver 0.9.28
usb 1-1: reset full speed USB device using ohci_hcd and address 2
lirc_dev: lirc_register_plugin: sample_rate: 0
lirc_mceusb2[2]: SMK eHome Infrared Transceiver on usb1:2
usbcore: registered new interface driver lirc_mceusb2
nvidia: module license 'NVIDIA' taints kernel.
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Encoder revision: 0x02060039
tveeprom 1-0050: Hauppauge model 26582, rev C699, serial# 8730932
tveeprom 1-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has no radio, has no IR receiver, has no IR transmitter
ivtv0: Autodetected Hauppauge WinTV PVR-150
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: Registered device video0 for encoder MPEG (4 MB)
ivtv0: Registered device video32 for encoder YUV (2 MB)
ivtv0: Registered device vbi0 for encoder VBI (1 MB)
ivtv0: Registered device video24 for encoder PCM audio (1 MB)
tuner 1-0061: type set to 50 (TCL 2002N)
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 18 (level, low) -> IRQ 19
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
ivtv1: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv1: Encoder revision: 0x02060039
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
tveeprom 2-0050: Hauppauge model 26032, rev C199, serial# 8750859
tveeprom 2-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: audio processor is CX25841 (idx 35)
tveeprom 2-0050: decoder processor is CX25841 (idx 28)
tveeprom 2-0050: has no radio, has IR receiver, has IR transmitter
ivtv1: Autodetected Hauppauge WinTV PVR-150
ivtv1: reopen i2c bus for IR-blaster support
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: Registered device video1 for encoder MPEG (4 MB)
ivtv1: Registered device video33 for encoder YUV (2 MB)
ivtv1: Registered device vbi1 for encoder VBI (1 MB)
ivtv1: Registered device video25 for encoder PCM audio (1 MB)
tuner 2-0061: type set to 50 (TCL 2002N)
ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command
0xc008561c!
ivtv1: i2c addr 0x44 not found for command 0x4008646f!
ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command
0x4008646d!
ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command
0xc008561c!
ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command
0xc008561c!
ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command
0xc008561c!
ivtv1: Initialized Hauppauge WinTV PVR-150, card #1
ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 21 (level, low) -> IRQ 20
ivtv: ==================== END INIT IVTV ====================
Here's lspci -vv :
[EMAIL PROTECTED] mythtv]# lspci -vv
00:00.0 Host bridge: Silicon Integrated Systems [SiS] SiS645DX Host &
Memory & AGP Controller
Subsystem: Silicon Integrated Systems [SiS] SiS645DX Host &
Memory & AGP Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d8000000 (32-bit, non-prefetchable)
[size=64M]
Capabilities: [c0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit-
FW- Rate=x4
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI
bridge (AGP) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: e4000000-e5ffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS961 [MuTIOL
Media IO] (rev 10)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus
Controller
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 1080 [size=32]
00:02.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] USB 1.0 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 16
Region 0: Memory at e6000000 (32-bit, non-prefetchable)
[size=4K]
00:02.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] USB 1.0 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e6001000 (32-bit, non-prefetchable)
[size=4K]
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev
d0) (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE
Controller (A,B step)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Region 0: [virtual] Memory at 000001f0 (32-bit,
non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3,
non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit,
non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3,
non-prefetchable) [size=1]
Region 4: I/O ports at f000 [size=16]
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]
AC'97 Sound Controller (rev a0)
Subsystem: AOPEN Inc. Unknown device 0248
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 20
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc00 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 150
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at dc000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 150
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: AOPEN Inc. Unknown device 0027
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at e000 [size=256]
Region 1: Memory at e6002000 (32-bit, non-prefetchable)
[size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX
4000 AGP 8x] (rev c1) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at e4000000 (32-bit, non-prefetchable)
[size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
[virtual] Expansion ROM at e5000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit-
FW- Rate=x4
Finally, here's lsmod:
[EMAIL PROTECTED] mythtv]# lsmod
Module Size Used by
sunrpc 153469 1
dm_mirror 25301 0
dm_mod 58509 1 dm_mirror
video 19909 0
sbs 19073 0
i2c_ec 9025 1 sbs
dock 13977 0
button 11857 0
battery 13893 0
asus_acpi 20445 0
backlight 10177 1 asus_acpi
ac 9157 0
ipv6 275585 24
lp 16265 0
8139cp 27073 0
wm8775 9933 0
cx25840 27345 0
tuner 60905 0
floppy 58789 0
snd_intel8x0 35676 3
snd_ac97_codec 93413 1 snd_intel8x0
ac97_bus 6465 1 snd_ac97_codec
snd_seq_dummy 7877 0
snd_seq_oss 33601 0
snd_seq_midi_event 11201 1 snd_seq_oss
snd_seq 51249 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_pcm_oss 43617 1
snd_mixer_oss 19393 2 snd_pcm_oss
nvidia 4710260 32
snd_pcm 75205 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_mpu401 12393 0
snd_mpu401_uart 12609 1 snd_mpu401
snd_rawmidi 26817 1 snd_mpu401_uart
snd_timer 25157 2 snd_seq,snd_pcm
snd_seq_device 11853 4
snd_seq_dummy,snd_seq_oss,snd_seq,snd_rawmidi
snd 53829 14
snd_intel8x0,snd_ac97_codec,snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_os
s,snd_pcm,snd_mpu401,snd_mpu401_uart,snd_rawmidi,snd_timer,snd_seq_devic
e
8139too 29889 0
snd_page_alloc 13769 2 snd_intel8x0,snd_pcm
ivtv 119568 2
i2c_sis96x 9669 0
mii 9409 2 8139cp,8139too
ide_cd 40673 0
i2c_algo_bit 11337 1 ivtv
cx2341x 15045 1 ivtv
tveeprom 18257 1 ivtv
videodev 29633 3 ivtv
v4l2_common 26945 5 cx25840,tuner,ivtv,cx2341x,videodev
pcspkr 7233 0
i2c_core 24897 9
i2c_ec,wm8775,cx25840,tuner,nvidia,ivtv,i2c_sis96x,i2c_algo_bit,tveeprom
soundcore 11681 3 snd
lirc_mceusb2 14340 1
lirc_dev 16292 1 lirc_mceusb2
cdrom 37345 1 ide_cd
v4l1_compat 16581 2 ivtv,videodev
parport_pc 30053 1
ns558 9153 0
parport 38537 2 lp,parport_pc
gameport 19401 2 ns558
ext3 126537 2
jbd 60905 1 ext3
ehci_hcd 34125 0
ohci_hcd 23621 0
uhci_hcd 26833 0
I'm really puzzled by this one, the card was working fine and then
suddenly - NOT! If anyone has any tips or ideas for fixing this, I'd
love to hear them. Thanks so much for your time and I'm more than happy
to post more info. I have also tried powering off overnight to clear
buffers and also have swapped the cards. If one card is plugged in,
that card works - if both are plugged in ivtv1 doesn't work.
yours,
tbaker
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
