Here I am again. I don't use a cassette deck. After I have finished the audio/command files I just put them in MP3 on the well-known player. Wow, now trying Rob's test, but it will take me some time. Anyway fantastic again!! regards Hans
Op zaterdag 26 februari 2022 om 12:02:49 UTC+1 schreef rob...@hotmail.com: > Hi Hans, > > I tested my proof of concept. I also attached the programs I used. In the > given video you see the results. > > This is how it works and what the video shows: > > - The PIC on the left is the transmitter. It uses two inputs (via the > wires that I connect to VCC or GND). One input enables the transmitter > (orange wire), that is it starts sending a tone. With the second input > (green wire) I can switch between a low tone and a high tone. > - The PWM output of the transmitter (PIC on the left) is connected to > the timer/counter input of timer 1 of the receiver PIC (PIC on the right). > - The PIC on the right resets timer 1 then it starts a measurement for > 100 ms after which it stops the measurement. Then it checks the value of > timer 1 (which in fact counts the number of 'ticks' generated by the PWM > frequency on its input) within a certain range. If this range is within > the > range of the low frequency, it will light up the yellow LED. If this range > is within the range of the high frequence it will light up the green LED. > If the counter value is outside these ranges (e.g. when there is no > signal) > both LEDs will be off. > > I am not sure if this is what you are looking for. I do not know if it > also works if you would record the transmitted signal to a casette tape. > > Link to video: https://youtu.be/49DAT0BQuAc > <https://youtu.be/49DAT0BQuAc> > Data via Tone <https://youtu.be/49DAT0BQuAc> > For more information on JAL, visit: http://justanotherlanguage.org/ > youtu.be > > > Kind regards, > > Rob > ------------------------------ > *Van:* jal...@googlegroups.com <jal...@googlegroups.com> namens hans < > hansvanve...@gmail.com> > *Verzonden:* zaterdag 26 februari 2022 11:37 > > *Aan:* jallib <jal...@googlegroups.com> > *Onderwerp:* Re: [jallib] PWM serial audio transmission > Hi, I'm using a 16f1827 with 8 ADC inputs that transmits the position of > the elements with the help of a potentiometer via the uart and performs the > movements. The audio track is recorded first and plays normally. At the > same time, the control signals on the other track are sent via the > ???????????? included. Afterwards I combine both tracks into a stereo > signal, moving the playback position of the signals forward a bit to > compensate for my reaction slowness. When played afterwards, the normal > audio track goes to the amplifier and the other track to the ??????????? > which then performs the movements. > > Op zaterdag 26 februari 2022 om 09:34:33 UTC+1 schreef Kiste: > > Hi Hans, > > that's about what I thought. I'm quite sure it can be done with a pic, one > or two capacitors and three to five resistors (or two resistors and > potentiometers). I'm just not sure yet what the best way would be. > > To keep things simple, you would probably want to build a transmitter with > manual controls, and a receiver which controls the actual "show". That way, > you can connect both modules to the tape recorder, and really see what the > output does from tape, while recording the show. > > Greets, > Kiste > > Am Samstag, 26. Februar 2022, 09:04:29 MEZ hat hans < > hansvanve...@gmail.com> Folgendes geschrieben: > > > Hey, > I get the impression that my question has not come across properly. I will > use a regular stereo audio signal. One track contains music, speech and > other normal sounds. The other track I want to use to record commands with > which I can move servos, lights, etc. At first I thought to do this with > DTMF but the MT8880 has died. Then I fiddled with the TCM3105, an > old-fashioned modem chip, but that didn't work either. I then read > something about PW application and hence my question. > I've been messing around with PICs for a long time, but because I'm purely > mechanical by nature, I have to limit myself to what I called LEGO work. > You make the stones and I make grateful use of them. > regards > Hans > > Op zaterdag 26 februari 2022 om 07:41:46 UTC+1 schreef vasile: > > Rob, obviously will work. :) But it would be weird to use a bunch of > external analog electronics. > BTW, with a PIC you can do a class D amplifier... what perhaps Hans > wanted is not far away: sampling and then digitizing via PWM. > Other choices are possible as well. Success on any variant you'll choose! > > On Fri, Feb 25, 2022 at 7:58 PM Rob CJ <rob...@hotmail.com> wrote: > > Hi Kiste, > > The reason that I think it still might work is because - what I mentioned > previously - is that my Apple II I had built in the past also just worked > with tones to store data (at that time only games 🙂). > > I copied a pice of the casette interface of the Apple II schematic diagram > I found on the internet. What you see is that with an opamp the audio is > input signal is converted to a digital signal and the rest of the > processing is done in software. There is no special chip on the board to > process this data stream. > > Also the data out is just a direct output of a flip-flop with some > resistors to reduce the signal outpt but not even a low pass filter. > > The variations in cassette speed will result in a variation of the tone so > if I use a tone range to detect the right tone it might work. > > Kind regards, > > Rob > > > > ------------------------------ > *Van:* jal...@googlegroups.com <jal...@googlegroups.com> namens hans < > hansvanve...@gmail.com> > *Verzonden:* vrijdag 25 februari 2022 16:20 > *Aan:* jallib <jal...@googlegroups.com> > *Onderwerp:* Re: [jallib] PWM serial audio transmission > > > Hi Vasile, > > In my time a birth was still followed by a placenta, nowadays an iphone > comes after. > > A long time ago I was infected by Wouter, Jal is even more persistent than > corona, see http://www.voti.nl/setalk/n_index.html > > > > regards Hans > > Op vrijdag 25 februari 2022 om 13:34:14 UTC+1 schreef vasile: > > Hi Hans. Congratulations for your young mind! There aren't many people > programming at your age. > You are a great example! > > On Fri, Feb 25, 2022 at 10:16 AM hans <hansvanve...@gmail.com> wrote: > > Hi Vasiele and others. > I was born before the last world war and I suspect most of you after it. > I hope it stays that way!! > Great, I can study today again. Thank you. > > Op vrijdag 25 februari 2022 om 06:58:52 UTC+1 schreef vasile: > > Kiste, not only the ZX81 but Sinclair Spectrum and most of it's clones did > the same. > The biggest problem was the tape speed variation (among the volume > variation which was corrected in romanian clones -and we had more than any, > I recall 5 different types). > > Hans, on the actual PIC18 series on which JAL works ( presuming you will > do with JAL) you might have some sampling speed issues. You need at least > 7.5us for an ADC sample and according to Nyquist theorem you need not 2x ( > which is pure theoretical) but at least 4x faster sampling than maximum > frequency you are recording. > After your AD is sampled, the PWM is not an issue, but you might > experience a small delay between real recorded speech and the PWM filtered > one. > If you plan to add voice for your puppet, then limiting to 4KHz may be a > good choice. > > best wishes, > hopefully not WW III, but in pace for playing nice... > > On Thu, Feb 24, 2022 at 10:38 PM 'Oliver Seitz' via jallib < > jal...@googlegroups.com> wrote: > > Hi Rob, > > connecting two PICs is not like an audio recording. Better connect the pic > to your soundcard to record and then playback, that way you'll get > something similar to a tape recorder. > > The difficulties when using audio equipment are (at least): > > - only alternating current is transmitted > - the volume is never exactly the same > - the frequency range is limited to like 100Hz-10kHz > - the line level voltage is less than 1V > > Reading should be possible by most PICs which have comparators. Only a > resistor is needed, then you can detect zero crossings. > > The Sinclair ZX81 used audio equipment as storage. A burst of three > oscillations coded a zero, five coded a one. The output was low-pass > filtered. You usually had to try loading a program several times, slightly > adjusting the volume, until you got lucky. > > Greets, > Kiste > > Am Donnerstag, 24. Februar 2022, 19:56:01 MEZ hat Rob CJ < > rob...@hotmail.com> Folgendes geschrieben: > > > Hi Hans, > > If I understand you right the only thing you want to do is to record a > signal or a sequence of signals on a casette player that can be used to > trigger something when the recording is played back right? > > If my initial suggestion would work - which may work since I have the idea > that my Apple II did more ore less the same thing - I could give it a try > to do a proof of concept. > > I may have a the problem that I do not have a casette recorder but I could > fake it by just connecting two PICs to see if that works. The final test > could then be done by you. > > Which PIC type are you using? > > Kind regards, > > Rob > > > > ------------------------------ > *Van:* jal...@googlegroups.com <jal...@googlegroups.com> namens hans < > hansvanve...@gmail.com> > *Verzonden:* donderdag 24 februari 2022 17:07 > *Aan:* jallib <jal...@googlegroups.com> > *Onderwerp:* Re: [jallib] PWM serial audio transmission > > Another piece of text: > So far I've done everything with MIDI. I used one midi channel for the > actions with a general command type. Then 2 data, one for the device nr > (16) and one for the command. (0-128) > This has worked well for years, but it does require a complete MIDI sound > package. > > Op donderdag 24 februari 2022 om 16:55:46 UTC+1 schreef hans: > > Hey , > I have tried a circuit with an MT8880 but the ICI has failed. I did hear > the 16 tones, but when I wanted to receive them, the chip gave up the ghost. > In theory I understand your suggestions well, but developing something > like this is not easy for me. I'm just a LEGO builder. > regards > Hans > > Op woensdag 23 februari 2022 om 19:30:37 UTC+1 schreef rob...@hotmail.com: > > Hi Hans, Kiste, > > You can still by DTMF decoders and I assume also DTMF encoders. Just look > at for example Aliexpress and type DTMF. > > But another suggestion. Many, many years ago I had built an Apple II and > I used cassette tapes to store and load games which was using tones > generated by the Apple II itself using two tones, one for high, one for low > and one as a lead-in tone (not sure in the lead-in tone was another tone) > to synchronze the start of the recorded program. You would not need this > lead-in tone in your case > > So I think it may not be that complex: > -) For recording on casette, generate this dual tone by the PIC via PWM > or maybe it is also sufficient to generate one tone in case of a 1 and no > tone in case of a 0 but I think this will be less reliable. > -) For playback, measure the length of the recorded PWM tone. If is is > within a certain range you accept it as a one and in case of two tones the > lower tone could be zero and the higher tone is one. > > As long as the tone frequency is not too high, I think this could work. > > A more advanced solution would be to use a phase locked loop (PLL) but I > am not sure if it will work. The PLL locks to the input signal so the > voltage that controls the oscillator goes up and down to follow (lock on > to) the input signal and this oscillator voltage signal could then be used > by a comparator of the PIC to detect a high or low tone. You can also use > the oscillator of the IC to generate the two tones by controlling the > oscillator voltage by the PIC. A typical IC for that is the HEF4046. I have > used this IC many many years ago too. This solution may be bit over the top > since you only want a kind of trigger signal > > But maybe the first solution is more doable. Just give it a try. > > Kind regards, > > Rob > > ------------------------------ > *Van:* 'Oliver Seitz' via jallib <jal...@googlegroups.com> > *Verzonden:* woensdag 23 februari 2022 09:58 > *Aan:* jal...@googlegroups.com <jal...@googlegroups.com> > *Onderwerp:* Re: [jallib] PWM serial audio transmission > > Hi Hans, > > 20 years ago I would have suggested using DTMF, but the decoder chips are > rare these days... > > PIC controllers include various peripherals which can be used to encode > and decode DC-free signals (which, apart from the frequency below, say, > 10kHz, is the requirement to be recorded as audio). On/off keying or > frequency shift keying are the easiest, I think. Which chips are you going > to use? > > Greets, > Kiste > > Am Mittwoch, 23. Februar 2022, 09:15:43 MEZ hat hans < > hansvanve...@gmail.com> Folgendes geschrieben: > > > Hello everyone, > I have been trying for a long time to place a serial signal on one track > of an audio recording which I can read afterwards. To make all kinds of > things happen at the same time as the audio is played. I have now tried to > do this with the old modem system ( TCM3105) but it failed hopelessly. I > read that there are also systems to do this using PWM. Does anyone have an > idea? > regards > Hans > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/773ca37b-9bed-4349-a8eb-32a5d8973df6n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/773ca37b-9bed-4349-a8eb-32a5d8973df6n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/201142693.752814.1645606718467%40mail.yahoo.com > > <https://groups.google.com/d/msgid/jallib/201142693.752814.1645606718467%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/d4803c41-505a-4297-81d5-7be0ef06b112n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/d4803c41-505a-4297-81d5-7be0ef06b112n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/DB6P195MB018301D93CBE73C8A9C74FF0E63D9%40DB6P195MB0183.EURP195.PROD.OUTLOOK.COM > > <https://groups.google.com/d/msgid/jallib/DB6P195MB018301D93CBE73C8A9C74FF0E63D9%40DB6P195MB0183.EURP195.PROD.OUTLOOK.COM?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/1712343432.941652.1645735109957%40mail.yahoo.com > > <https://groups.google.com/d/msgid/jallib/1712343432.941652.1645735109957%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/f8c9ab42-0f79-4899-8974-bab64a1785c4n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/f8c9ab42-0f79-4899-8974-bab64a1785c4n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/068d3769-e491-4f55-9daa-7a2d1e612df8n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/068d3769-e491-4f55-9daa-7a2d1e612df8n%40googlegroups.com?utm_medium=email&utm_source=footer>. > > > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/DB6P195MB01832EBF0D9FB18F67DA4BFFE63E9%40DB6P195MB0183.EURP195.PROD.OUTLOOK.COM > > <https://groups.google.com/d/msgid/jallib/DB6P195MB01832EBF0D9FB18F67DA4BFFE63E9%40DB6P195MB0183.EURP195.PROD.OUTLOOK.COM?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > > https://groups.google.com/d/msgid/jallib/ee4cce04-b58c-499a-acc0-7f43953ee042n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/ee4cce04-b58c-499a-acc0-7f43953ee042n%40googlegroups.com?utm_medium=email&utm_source=footer> > > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/ca7dfe38-7c9b-459c-a6d6-fe65fe956a04n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/ca7dfe38-7c9b-459c-a6d6-fe65fe956a04n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to jallib+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/e8f19d16-fc85-4083-a042-d8bc0964ce87n%40googlegroups.com.