I've seen it complain about https certs before in pre-install, but with a complete install when you're not using it - it no longer complains.
Probably something like that. On Nov 29, 2012, at 8:02 PM, Ali Sumsam <ali+juniper...@eintellego.net> wrote: > and here comes the interesting part. If I try to validate after i have > upgraded the router to the new JunOS. It just validates successfully. > > Regards, > *Ali Sumsam CCIE* > *Network Engineer - Level 3* > eintellego Pty Ltd > a...@eintellego.net ; www.eintellego.net > > Phone: 1300 753 383 ; Fax: (+612) 8572 9954 > > Cell +61 (0)410 603 531 > > facebook.com/eintellego > PO Box 7726, Baulkham Hills, NSW 1755 Australia > > The Experts Who The Experts Call > Juniper - Cisco – Brocade - IBM > > > > On Fri, Nov 30, 2012 at 12:36 PM, Stacy W. Smith <st...@acm.org> wrote: > >> Can you share the current version and existing config? If it really is as >> simple as you say, then I would not expect a problem, but it would be >> interesting to investigate why it's complaining. >> >> --Stacy >> >> On Nov 29, 2012, at 6:33 PM, Ali Sumsam <ali+juniper...@eintellego.net> >> wrote: >>> but that will kinda bypass it. >>> Should i worry about it or just ignore it? >>> >>> Regards, >>> *Ali Sumsam CCIE* >>> *Network Engineer - Level 3* >>> eintellego Pty Ltd >>> a...@eintellego.net ; www.eintellego.net >>> >>> Phone: 1300 753 383 ; Fax: (+612) 8572 9954 >>> >>> Cell +61 (0)410 603 531 >>> >>> facebook.com/eintellego >>> PO Box 7726, Baulkham Hills, NSW 1755 Australia >>> >>> The Experts Who The Experts Call >>> Juniper - Cisco – Brocade - IBM >>> >>> >>> >>> On Fri, Nov 30, 2012 at 12:30 PM, OBrien, Will <obri...@missouri.edu> >> wrote: >>> >>>> no-validate >>>> >>>> That is, request system software install no-validate blah >>>> >>>> >>>> On Nov 29, 2012, at 7:25 PM, Ali Sumsam wrote: >>>> >>>>> Hi, >>>>> I have a brand new MX5 router for one of my customers. The only >>>>> configuration I have on this router is >>>>> >>>>> 1, one login name and password >>>>> 2, IP address on FXP0 >>>>> 3, telnet and ftp service. >>>>> >>>>> I have uploaded Junos jinstall-ppc-11.2R5.4-export-signed.tgz, which is >>>> the >>>>> recommended one for MX5 on juniper site. >>>>> >>>>> >>>>> When i try to validate this JunOS, it gives me following error. >>>>> >>>>> mgd: error: configuration check-out failed >>>>> Validation failed >>>>> WARNING: Current configuration not compatible with >>>>> /var/tmp/jinstall-ppc-11.2R5.4-export-signed.tgz >>>>> >>>>> Any suggestion. Can I just ignore this error and live with it? >>>>> >>>>> Regards, >>>>> >>>>> >>>>> *Ali Sumsam CCIE* >>>>> *Network Engineer - Level 3* >>>>> eintellego Pty Ltd >>>>> a...@eintellego.net ; www.eintellego.net >>>>> >>>>> Phone: 1300 753 383 ; Fax: (+612) 8572 9954 >>>>> >>>>> Cell +61 (0)410 603 531 >>>>> >>>>> facebook.com/eintellego >>>>> PO Box 7726, Baulkham Hills, NSW 1755 Australia >>>>> >>>>> The Experts Who The Experts Call >>>>> Juniper - Cisco – Brocade - IBM >>>>> _______________________________________________ >>>>> juniper-nsp mailing list juniper-nsp@puck.nether.net >>>>> https://puck.nether.net/mailman/listinfo/juniper-nsp >>>> >>>> >>> _______________________________________________ >>> juniper-nsp mailing list juniper-nsp@puck.nether.net >>> https://puck.nether.net/mailman/listinfo/juniper-nsp >> >> > _______________________________________________ > juniper-nsp mailing list juniper-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/juniper-nsp _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp