I put this into my ACX5048 in the lab today. actually 2 of them. QSFP+-40G-ER4 (aka QSFPP-40GBASE-ER4) SMF 40 km 1310 nm optic
Optic is seen in cli, but I see no led's on chassis and when I plug them into each other, interfaces stay up/down. Is there something I need to do to make this 40 gig optic work in the ACX5048 (JUNOS 15.1X54-D61.6) ? {master:0} agould@eng-lab-5048-2> show interfaces terse | grep et- et-0/0/48 up down et-0/0/49 up down {master:0} agould@eng-lab-5048-2> show interfaces et-0/0/48 Physical interface: et-0/0/48, Enabled, Physical link is Down Interface index: 657, SNMP ifIndex: 582 Link-level type: Ethernet, MTU: 1514, LAN-PHY mode, Speed: 40Gbps, BPDU Error: None, MAC-REWRITE Error: None, Loopback: Disabled, Source filtering: Disabled, Flow control: Disabled, Media type: Fiber Device flags : Present Running Down Interface flags: Hardware-Down SNMP-Traps Internal: 0x4000 Link flags : None CoS queues : 8 supported, 8 maximum usable queues Current address: 20:4e:71:45:d3:d3, Hardware address: 20:4e:71:45:d3:d3 Last flapped : 2017-10-04 10:26:33 CDT (00:09:14 ago) Input rate : 0 bps (0 pps) Output rate : 0 bps (0 pps) Active alarms : LINK Active defects : LINK Interface transmit statistics: Disabled {master:0} agould@eng-lab-5048-2> show interfaces et-0/0/49 Physical interface: et-0/0/49, Enabled, Physical link is Down Interface index: 658, SNMP ifIndex: 583 Link-level type: Ethernet, MTU: 1514, LAN-PHY mode, Speed: 40Gbps, BPDU Error: None, MAC-REWRITE Error: None, Loopback: Disabled, Source filtering: Disabled, Flow control: Disabled, Media type: Fiber Device flags : Present Running Down Interface flags: Hardware-Down SNMP-Traps Internal: 0x4000 Link flags : None CoS queues : 8 supported, 8 maximum usable queues Current address: 20:4e:71:45:d3:d7, Hardware address: 20:4e:71:45:d3:d7 Last flapped : 2017-10-04 10:27:53 CDT (00:07:56 ago) Input rate : 0 bps (0 pps) Output rate : 0 bps (0 pps) Active alarms : LINK Active defects : LINK Interface transmit statistics: Disabled {master:0} agould@eng-lab-5048-2> show chassis hardware Hardware inventory: Item Version Part number Serial number Description Chassis (removed...) ACX5048 Pseudo CB 0 Routing Engine 0 BUILTIN BUILTIN ACX5K Routing Engine FPC 0 REV 07 650-060546 (removed...) ACX5048 CPU BUILTIN BUILTIN FPC CPU PIC 0 BUILTIN BUILTIN 48x10G-6x40G Xcvr 48 REV 01 740-059185 (removed...) QSFP+-40G-ER4 Xcvr 49 REV 01 740-059185 (removed...) QSFP+-40G-ER4 Power Supply 0 REV 04 740-043886 (removed...) JPSU-650W-DC-AFO Power Supply 1 REV 04 740-043886 (removed...) JPSU-650W-DC-AFO Fan Tray 0 ACX5K Fan Tray 0, Front to Back Airflow - AFO Fan Tray 1 ACX5K Fan Tray 1, Front to Back Airflow - AFO Fan Tray 2 ACX5K Fan Tray 2, Front to Back Airflow - AFO Fan Tray 3 ACX5K Fan Tray 3, Front to Back Airflow - AFO Fan Tray 4 ACX5K Fan Tray 4, Front to Back Airflow - AFO {master:0} agould@eng-lab-5048-2> show chassis pic pic-slot 0 fpc-slot 0 FPC slot 0, PIC slot 0 information: Type 48x10G-6x40G State Online PIC version 2.7 Uptime 99 days, 23 hours, 26 minutes, 3 seconds PIC port information: Fiber Xcvr vendor Wave- Xcvr Port Cable type type Xcvr vendor part number length Firmware 48 40GBASE ER4 SM JUNIPER-FINISAR FTL4E1QE1C-J3 1301 nm 0.0 49 40GBASE ER4 SM JUNIPER-FINISAR FTL4E1QE1C-J3 1301 nm 0.0 - Aaron _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp