Hi Bill The first rope beads that I made were done by the hand cranking method, "Talk about a long rope..." ;-) Using the limit switch is much easer. I used a button cutting bit from Magnate. (#352) , but did not go the full plung depth. (I did not relise my mistake until I was more than half way done, and at that point, I say keep everything uniformed. SAME IS GOOD, Even if its wrong.the eyes will not ketch it. Most of the time.) ;-) gota run. Have a good day. C.A.G.
----- Original Message ----- From: "Bill Bulkeley" <bulke...@mmnet.com.au> To: legacy-ornamental-mills@googlegroups.com Sent: Monday, January 26, 2015 4:19:29 AM Subject: RE: rope and beads Pretty cool curt if we didn’t have or could not build what you have i guess its just one turn of the cranking handle for each bead spacing. What cutter did you use to cut the bead Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of CURTIS GEORGE Sent: Monday, 26 January 2015 7:37 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: rope and beads Hello and Good morning. Yes I was Showing off, Just a little bit, The rope beads are very easy to make, It just took me a little while to figure out how to do it. I am sending two pictures that explain how it was done, But In a Nut shell I used the gears and pitch to make the ropes and then set up this jig to stop the motor every 1/4" rotation. The screw turns, and once the handle hits the limit switch it stops, where I then plung down to make a bead, then hit the over ride on my limit switch, which advances the spindle on the next button location. Pretty simple! Right? ;-) Now there is some minor adjustment parts that I want to still make, I am going to make the handle/stop adjustable so that I can fine tune the buttons spacing, But that's it for now. I hope this helps someone out there, next project. It is fun and easy to do. Have a good day all. C.A.G. ----- Original Message ----- From: "Okla Mike (Liltwisted)" <legacym...@iglide.net> To: legacy-ornamental-mills@googlegroups.com Sent: Sunday, January 25, 2015 10:52:15 PM Subject: Re: rope and beads Nice Curt! You are just showing off now LOL Mike OK On 1/25/2015 7:11 PM, CURTIS GEORGE wrote: Hello everyone. I got some play time in the shop, this is just a test project but I thought some of you might like to see what I did. Any questions or comments are, As always welcome. C.A.G -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com . To post to this group, send email to legacy-ornamental-mills@googlegroups.com . Visit this group at http://groups.google.com/group/legacy-ornamental-mills . For more options, visit https://groups.google.com/d/optout . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com . To post to this group, send email to legacy-ornamental-mills@googlegroups.com . Visit this group at http://groups.google.com/group/legacy-ornamental-mills . For more options, visit https://groups.google.com/d/optout . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com . To post to this group, send email to legacy-ornamental-mills@googlegroups.com . Visit this group at http://groups.google.com/group/legacy-ornamental-mills . For more options, visit https://groups.google.com/d/optout . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com . To post to this group, send email to legacy-ornamental-mills@googlegroups.com . Visit this group at http://groups.google.com/group/legacy-ornamental-mills . For more options, visit https://groups.google.com/d/optout . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at http://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.