Hi Mike, The ramping of the ends is in my opinion the "classic" look of hand carving style that are prominent in antique furniture.
On Mar 1, 2018, 12:29 PM, at 12:29 PM, "Okla Mike (Liltwisted)" <legacym...@iglide.net> wrote: >I believe it is clean because of the speed of cut, no hesitation at the > >ends. > >In Tim's suggestion, cutting from the side, there will be a very >notable >difference in the look of the ends of the flutes. Instead of the sharp > >radius start and stop, there will be a ramping in and out that will be >the radius of the major diameter of the bit. Tapered in so to speak. >Also, the cut will have to be a climb cut to remove stock and then a >final clean cut. The next area of concern is the lifting of the grain >rip out at the exit of the cut. These are all controllable but as I >said are just areas to be aware of. I really like the positive index >stops as well as the bearing follower. > >Mike OK > >On 3/1/2018 9:31 AM, Tom Dotta wrote: >> HI All >> Most impressively clean cut, no burning, even though the wood looks >> full of resin. Do you think the cutter has a greater angle of relief >> than ours? Cheers Tom Dotta >> >> On Thu, Mar 1, 2018 at 6:33 AM, Richard Ellis <rchrd.ell...@gmail.com > >> <mailto:rchrd.ell...@gmail.com>> wrote: >> >> Tim >> I am not too sure how to hold such objects------- other than on >> the Revo's table, rotary or the normal flat one. A cheaper cutter >> would suffice me thinks!!?? >> >> On Thursday, March 1, 2018 at 11:54:59 AM UTC, Tim wrote: >> >> I like his method of a follower. If I was doing this on the >> legacy I would turn the piece on it's side and use a side >> cutting bit with a bearing. Simple stuff and you don't have >> to modify anything. >> >> Tim >> On Mar 1, 2018, at 1:34 AM, Richard Ellis >> <rchrd....@gmail.com> wrote: >> >> Hi all thought this may be of interest to some So have >> re:posted it. Thanks Curt ---some possibilities there >> Richard >> >> Curt George >> 11/12/17 >> >> Well not exactly, but his set up and jigs could be used >on >> the Legacy... I THINK OF IT AS A GOOD LEARNING >EXPERIENCE. >> Enjoy the video. >> >> https://www.youtube.com/watch?v=2-zjc5qYFyQ >> <https://www.youtube.com/watch?v=2-zjc5qYFyQ> >> >> C.A.G. >> >> -- >> You received this message because you are subscribed to the >Google >> Groups "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, >> send an email to >> legacy-ornamental-mills+unsubscr...@googlegroups.com >> <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com>. >> To post to this group, send email to >> legacy-ornamental-mills@googlegroups.com >> <mailto:legacy-ornamental-mills@googlegroups.com>. >> Visit this group at >> https://groups.google.com/group/legacy-ornamental-mills >> <https://groups.google.com/group/legacy-ornamental-mills>. >> For more options, visit https://groups.google.com/d/optout >> <https://groups.google.com/d/optout>. >> >> >> -- >> You received this message because you are subscribed to the Google >> Groups "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, >send >> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com >> <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com>. >> To post to this group, send email to >> legacy-ornamental-mills@googlegroups.com >> <mailto:legacy-ornamental-mills@googlegroups.com>. >> Visit this group at >> https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. > >-- >You received this message because you are subscribed to the Google >Groups "Legacy Ornamental Mills" group. >To unsubscribe from this group and stop receiving emails from it, send >an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >To post to this group, send email to >legacy-ornamental-mills@googlegroups.com. >Visit this group at >https://groups.google.com/group/legacy-ornamental-mills. >For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
