* Hi Bill get well soon,* I too have kidney problems -- i think it is a result of medicines that they used to cure my leukaemia. Trouble with getting old!! Hi Curt It is 08.00 over here in the U.K. On my Revo I am sure I can hold it with the Clamps that I have. How to make a smooth finish is a question to sort out. I could also use a drum type sander, ----end of a belt sander??? However I will try his method on a flat table ---see how it goes. Richard
On Friday, March 2, 2018 at 5:26:21 AM UTC, Curt George wrote: > > Hello everyone. > I like Tim's idea of using a side cutter. but how to hold it??? > How about making a large spindle, lets say 4" dia. then make a flat on > the spindle, to support the wood. Sorta like using bench dogs... > Here is another attempt to picture What I am suggesting, mount a flat > board,with clamping set up in-between centers.(or for that matter, just use > screws form the bottom?) this way you can hold the wood and then turn it > on its side for slide cutting? > > 1001 ways to do anything. This is one way That might work...? ;-) > > Have a good night all. > C.A.G. > > > > > On Thursday, March 1, 2018 10:01 AM, Michael Kratky <kra...@roadrunner.com > <javascript:>> wrote: > > > Richard, > Great idea no matter the language barrier, the bearing follower is > standard equipment on most trim routers I can see how it can easily be > adapted, I’m going to look into this further. > Thanks for posting, > Michael K > > *From:* legacy-orna...@googlegroups.com <javascript:> [mailto: > legacy-ornamental-mills@googlegroups.com <javascript:>] *On Behalf Of > *Richard > Ellis > *Sent:* Thursday, March 01, 2018 4:34 AM > *To:* Legacy Ornamental Mills > *Subject:* Re: Post from Russia > > Hi all thought this may be of interest to some So have re:posted it. > Thanks Curt ---some possibilities there > Richard > > Curt George > [ ] > [ ] > 11/12/17 > [ ] > [ ] > Well not exactly, but his set up and jigs could be used on the Legacy... I > THINK OF IT AS A GOOD LEARNING EXPERIENCE. > Enjoy the video. > > https://www.youtube.com/watch?v=2-zjc5qYFyQ > > C.A.G. > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com > <javascript:>. > To post to this group, send email to legacy-orna...@googlegroups.com > <javascript:>. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com > <javascript:>. > To post to this group, send email to legacy-orna...@googlegroups.com > <javascript:>. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
