I'm with you bill. This is a rotary table job on a stock legacy. Are the pockets getting smaller as the pattern goes to the center? I think I see shift in the pattern as it goes to the center. Is that right? To me it looks like a 3" diameter piece.
Tim On May 4, 2018, 5:01 PM, at 5:01 PM, Bill Bulkeley <bulke...@mmnet.com.au> wrote: >Am i missing something doesn’t the router bit have to be vertical to >the lid to produce the pattern how can putting it between centres work? >if you can mount the router at 90 degrees you could plunge cut the >pattern then > > > >Please explain what I’m not getting > > > >Bill > > > >From: 'Curt George' via Legacy Ornamental Mills >[mailto:legacy-ornamental-mills@googlegroups.com] >Sent: Friday, 4 May 2018 10:47 PM >To: legacy-ornamental-mills@googlegroups.com >Subject: Re: What do you think of this??? > > > >Hello and Good-morning > > > >Yes the rotary table might work, > >But the way I think I will try it, > >Is to mount it between centers. using a soft touch,( piece of wood or >other meteral to hold the part from the tail-stock end onto the work ) >Then you > >could just do the indexing like a spindle, starting close to the >center, and bumping the router bit into the wood, then raising the bit, >and repeating the process > >until you have done. > >once you lay out the pattern, on the work piece and the indexing plate, >it should be a slow but easy job. > >this bowl looks like it was cut with a 1/2" or 3/8" router bit, but any >bit would give you > >some interesting contrast. > >As far as the tapper goes, that could all be done with your stop >collars, as you raise the bit up, for the next set of cuts, just move >your stop collar in, "X" amount to adjust > >for the angle, as long as everything is done the same, it will look >uniformed. > > > >I do plan to try this idea for my self, very soon. I will let you all >know if it works out for me, or not. > >I feel pretty good it will work. > >more latter. > >C.A.G. > > > >On Friday, May 4, 2018 3:59 AM, Bill Bulkeley <bulke...@mmnet.com.au> >wrote: > > > >Interesting curt a job for the rotary table that pattern, what do you >think > > > >Bill > > > >From: 'Curt George' via Legacy Ornamental Mills >[mailto:legacy-ornamental-mills@googlegroups.com] >Sent: Friday, 4 May 2018 2:09 PM >To: Legacy-Ornamental-Mills >Subject: What do you think of this??? > > > >Inline image > >Sadly I can not take the credit for making this. but I think it is >pretty neat, > >I know that something like this could be done on the Legacy.What do you >people think? > >How would you make this? > >I have my own ideas and do plan to try... > > > >C.A.G. > > > > ><http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > > >Virus-free. ><http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> >www.avg.com > >-- >You received this message because you are subscribed to the Google >Groups "Legacy Ornamental Mills" group. >To unsubscribe from this group and stop receiving emails from it, send >an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >To post to this group, send email to >legacy-ornamental-mills@googlegroups.com. >Visit this group at >https://groups.google.com/group/legacy-ornamental-mills. >For more options, visit https://groups.google.com/d/optout. > >-- >You received this message because you are subscribed to the Google >Groups "Legacy Ornamental Mills" group. >To unsubscribe from this group and stop receiving emails from it, send >an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >To post to this group, send email to >legacy-ornamental-mills@googlegroups.com. >Visit this group at >https://groups.google.com/group/legacy-ornamental-mills. >For more options, visit https://groups.google.com/d/optout. > > > >-- >You received this message because you are subscribed to the Google >Groups "Legacy Ornamental Mills" group. >To unsubscribe from this group and stop receiving emails from it, send >an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >To post to this group, send email to >legacy-ornamental-mills@googlegroups.com. >Visit this group at >https://groups.google.com/group/legacy-ornamental-mills. >For more options, visit https://groups.google.com/d/optout. > >-- >You received this message because you are subscribed to the Google >Groups "Legacy Ornamental Mills" group. >To unsubscribe from this group and stop receiving emails from it, send >an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >To post to this group, send email to >legacy-ornamental-mills@googlegroups.com. >Visit this group at >https://groups.google.com/group/legacy-ornamental-mills. >For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
