Unless my memory is really failing, I've shown examples in the past messages. Anyone can make them. I'll see if I can find the photos or I would search for "low profile" in the Google groups messages.
On Dec 12, 2018, 6:18 AM, at 6:18 AM, Harvey Matyas <hmatyas0...@gmail.com> wrote: >Tim > >Where are the low profile clamps located? I checked the site at >https://ornamentalmills.com/turningaround/index.html > >Thank you. > >Harvey > > >On Wed, Dec 12, 2018 at 12:55 AM Tim Krause <artmarb...@comcast.net> >wrote: > >> I thought of putting some pem inserts into the rotary table so you >could >> do what you are saying. I just never got around to either needing to >> making it happen. >> >> Another thought I will pass on that low profile clamps will work >better >> than many of the larger knobs sold by rockler. At least be careful >when >> cutting. I have posted on sever low profile clamps in this group. >> >> I forgot where you landed in Oregon, care to remind me. >> >> Tim >> On Dec 11, 2018, at 8:47 PM, rookie <alumacraf...@gmail.com> wrote: >>> >>> Thank you Tim for the information on your efforts to improve upon >the >>> rotary table, look's like great minds think alike, :-) Sharing of >this >>> info is just one of the many great things about this Legacy group. >I went >>> to the Rockler woodworking store today in Beaverton and picked-up >the >>> T-track rail as well as several t-track accessories, hold downs, >small >>> toggles, stops, with the intention of creating new plywood rotary >tables >>> with the T-track rails/hold-downs which should give you more control >of the >>> workpiece staying put on the table when being routed. I plan on >making >>> several wood rotary tables that will have different hold down >features for >>> different applications. To make switching out the new wood >table"jigs" >>> easier, I'm going to deviate from Legacy's way of fastening the >original >>> MDF wood table to the round turntable base with four #8 screws, >their >>> design, (screws are fastened underneath the table) forces you to >remove the >>> entire rotary table from the rails. The plan is to make is so the >new wood >>> tables, aka, hold-down jigs, will fasten to the metal turntable from >the >>> top. Thanks again, some great ideas, I'd like to have you for a >neighbor. >>> >>> >>> >>> On Sunday, December 9, 2018 at 8:44:01 PM UTC-8, rookie wrote: >>> >>>> Greetings to all. Back in the shop, (my winter hang-out), and >looking >>>> to make some fun wood X-mas gifts. I've dusted off the Legacy 900 >and >>>> installed the rotary table, always a pain to line up the center of >the >>>> router to the center of the rotary table. I watched the Legacy >training >>>> dvd's on centering the rotary table and have used that method in >the past >>>> but there has to be a faster more accurate way, any thoughts or >experience >>>> on this? Also looking to making some hold down jigs on the rotary >table, >>>> I've been using double stick tape but that method has some >drawbacks, i.e., >>>> often leaves a sticky residue, fails at time to hold down wood >piece which >>>> results in ruining the work, also with thin pieces the risk of >breaking >>>> while trying to release workpiece from the tape/table. I picked-up >some >>>> nice grade 3/4" plywood today with the intention of making several >rotary >>>> tables with different hold down features, T-Tracks come to mind as >these >>>> have a lot of assorted accessories you can use with a T-Track. >Shell in >>>> Oregon. >>>> >>> -- >>> You received this message because you are subscribed to the Google >Groups >>> "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, >send an >>> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >>> To post to this group, send email to >>> legacy-ornamental-mills@googlegroups.com. >>> Visit this group at >>> https://groups.google.com/group/legacy-ornamental-mills. >>> For more options, visit https://groups.google.com/d/optout. >>> >> -- >> You received this message because you are subscribed to the Google >Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, >send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To post to this group, send email to >> legacy-ornamental-mills@googlegroups.com. >> Visit this group at >> https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> > >-- >You received this message because you are subscribed to the Google >Groups "Legacy Ornamental Mills" group. >To unsubscribe from this group and stop receiving emails from it, send >an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >To post to this group, send email to >legacy-ornamental-mills@googlegroups.com. >Visit this group at >https://groups.google.com/group/legacy-ornamental-mills. >For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
