No the revos rails don’t drop very far to fit taller jobs, moving the table out and down would give you more Hight but then you would need to put longer cross slide rails so you could reach the middle of the rotary table with the router which I do have. Moving the rotary table out and down might cause stability problems too I guess you could brace it underneath with a couple of small screw jacks anything is possible. I do that with the revos milling table when I’m planning large jobs on it.
Bill From: legacy-ornamental-mills@googlegroups.com <legacy-ornamental-mills@googlegroups.com> On Behalf Of Tim Sent: Monday, 9 September 2019 2:35 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Extended Revo And raiser Isn’t the limit because of the limit of the router bit range? Could the depth be improved with a different mounting of the rotary table? Tim From: bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> Sent: Sunday, September 8, 2019 3:45 PM To: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> Subject: RE: Extended Revo And raiser Nice Richard why the plexiglass top? The only problem with the revo roatry table is you cant get a lot of height. on your 900 you will I have never tried the revos one on a 900 as I have 2 a revo one and a 900s one be interesting to see how you fit it Bill From: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > On Behalf Of Richard Ellis Sent: Monday, 9 September 2019 12:35 AM To: Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > Subject: Re: Extended Revo And raiser Thought I would put a pic of my Revo Rotary Table. Note the visibility of it Have not tried it on the 900 so don't know if it would be better Richard On Saturday, September 7, 2019 at 5:01:24 AM UTC+1, Curt George wrote: Pretty Slick! You almost make me wish I had bought the REVO. (Sadly they did not make it until I had owned my 1000ex for a few years,by then.) (its just tool envy!) ;-) (As a side note, I called the REVO, a side saddle unit, when Legacy first offered it.) ;-p Today? Well its a different story. NIce job on both your fine tune risers as well as your spindle work. C.A.G. On Friday, September 6, 2019, 01:34:06 PM EDT, Richard Ellis <rchrd...@gmail.com <javascript:> > wrote: Hi Curt I thought it best to start a new topic .The Revo is just the same but a bit longer. I have a drive to the spindle 414 v 3 ph. motor through an inverter Suitable for the U.K. The raisers at each end are a great help .All they consist of are a long coach bolt with a nut welded to a bit of angle iron. I drilled a small hole in the top of the bolt and epoxied a set screw in it. ,same size as the large legacy Allen wrench I can if a large up or down movement is needed use a cordless drill with a bit of Allen key in it. The wood work on the bolt enables a fine adjustment by hand ( foregoing the Allen wrench, ) Hope you can understand it Richard -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <javascript:> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/d9e6df2b-7a78-49fe-b625-3c5559dcdf3a%40googlegroups.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/d9e6df2b-7a78-49fe-b625-3c5559dcdf3a%40googlegroups.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/b44afedb-4be4-4e39-a737-3a7542b98def%40googlegroups.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/b44afedb-4be4-4e39-a737-3a7542b98def%40googlegroups.com?utm_medium=email&utm_source=footer> . <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> www.avast.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/003201d56697%241733e730%24459bb590%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/003201d56697%241733e730%24459bb590%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/5d75d68a.1c69fb81.749f7.c151SMTPIN_ADDED_MISSING%40gmr-mx.google.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/5d75d68a.1c69fb81.749f7.c151SMTPIN_ADDED_MISSING%40gmr-mx.google.com?utm_medium=email&utm_source=footer> . --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000501d566d9%24dd8e3b00%2498aab100%24%40mmnet.com.au.
