Here you go Richard https://www.amazon.co.uk/TONGXU-Position-Accessory-Auxiliary-Woodworking/dp/B07VMKZ65N/ref=pd_sbs_60_3/261-2781080-9222905?_encoding=UTF8 <https://www.amazon.co.uk/TONGXU-Position-Accessory-Auxiliary-Woodworking/dp/B07VMKZ65N/ref=pd_sbs_60_3/261-2781080-9222905?_encoding=UTF8&pd_rd_i=B07VMKZ65N&pd_rd_r=c3cefc80-fb5b-4fa1-9644-613897b30d4d&pd_rd_w=RjgiZ&pd_rd_wg=aYaGT&pf_rd_p=2773aa8e-42c5-4dbe-bda8-5cdf226aa078&pf_rd_r=A8RQWJ7SVGQD8KDE2VVC&psc=1&refRID=A8RQWJ7SVGQD8KDE2VVC> &pd_rd_i=B07VMKZ65N&pd_rd_r=c3cefc80-fb5b-4fa1-9644-613897b30d4d&pd_rd_w=RjgiZ&pd_rd_wg=aYaGT&pf_rd_p=2773aa8e-42c5-4dbe-bda8-5cdf226aa078&pf_rd_r=A8RQWJ7SVGQD8KDE2VVC&psc=1&refRID=A8RQWJ7SVGQD8KDE2VVC
a bit more reenable price I wouldn’t pay that much either and you get 4 Bill From: legacy-ornamental-mills@googlegroups.com <legacy-ornamental-mills@googlegroups.com> On Behalf Of Richard Ellis Sent: Tuesday, 23 June 2020 5:11 PM To: Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com> Subject: Re: Box making Mac. & Roger I have just been onto the woodworkers workshop To have a look at the clamping squares. I,, like Roger,, have been selling and buying all sorts of thing from land to lathe parts. But buying is where the profit is if you use your brains. To buy squares at £64.95 -------- must think I am stupid. On Monday, June 22, 2020 at 8:15:21 PM UTC+1, Va Oak wrote: Richard, I would do the same as Bill. My SawStop, for all practical purposes, is "Dead On" at making 90º cuts. I do not have confidence in the precision capability of the LOM to attempt to perfectly "square" a piece of wood on it. The LOM is great for a lot - but not to establish perfect 90º angles four times to create a cube. (backlash and just the slight "slop"in the rail tracking) If somewhere between 88 and 92 degrees was "ok" then I might try the LOM. I suggest you contact a GREAT American precision manufacturer - Woodpeckers - and buy a few of their <https://www.woodpeck.com/clamping-squares-plus.html> "Clamping Squares" (Sorry, Roger, they do not make cheese.) They will square up whatever it is you want squared up. There are a variety of ways you can employ them to accomplish that. Be well - and do good. Mac _____ _____ -----Original Message----- From: bulk...@mmnet.com.au <javascript:> Sent: Jun 22, 2020 1:58 PM To: legacy-orna...@googlegroups.com <javascript:> Subject: RE: Box making I would do it on the spindle with the indexing gear using a square off the rails to check it. But I’m guessing I usually square all my stock on the table saw. Bill _____ _____ From: legacy-orna...@googlegroups.com <javascript:> <legacy-orna...@googlegroups.com <javascript:> > On Behalf Of Richard Ellis Sent: Tuesday, 23 June 2020 2:19 AM To: Legacy Ornamental Mills <legacy-orna...@googlegroups.com <javascript:> > Subject: Box making I am making some small boxes 4x8 inch 4 inch deep. I have done all the box joints using 1/2 inc cutter, Four turns with the handle worked well. Now glue up ----------I have block of wood 3 1/2 inch but not quite square. The question is how to make it square on the Legacy---45 180 90 or planing on the table, Table will get two sides o.k. but how about the others. The block is for clamping, one corner off for glue run out. Richard -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/86c421ce-c5f6-43ce-8170-e2c8d555d501o%40googlegroups.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/86c421ce-c5f6-43ce-8170-e2c8d555d501o%40googlegroups.com?utm_medium=email&utm_source=footer> . -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000201d64935%2464355740%242ca005c0%24%40mmnet.com.au.
