these work great I did some as a test and far better then splitting a glue joint in my book. Kind Regards,
Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Nov 30, 2020 at 4:51 PM Ray Leaman <view...@gmail.com> wrote: > Thanks Ken I first heard of putting paper between glue ups way back in my > pattern making training in trade school. I have used that trick many > times over the years. I want to try the pilaster dogs just to see how they > work since they came with my new mill. If things don 't work out I'll fall > back on our alternative method (which may actually be easier). > > On Mon, Nov 30, 2020 at 2:49 AM Ken Fisher <kfishe...@outlook.com> wrote: > >> Ray, >> If you want to make quarter rounds just glue up 4 pieces of wood to make >> up the square. Which in turn gets turned round or with spirals or whatever >> you like. To make it easy to break apart use paper in the glue joints. >> >> Ken >> >> Sent from my iPhone >> >> On Nov 29, 2020, at 11:38 PM, M.W.Foscue <mwfos...@earthlink.net> wrote: >> >> >> Ray, >> Note: What comes out from turning using a pair of Pilaster Dogs is not a >> "quarter round" (a quarter of a round piece of stock). >> The Dogs give you a much "flatter" piece - much more like an ellipse when >> viewed from the ends. >> I hope that helps. >> Mac >> ------------------------------ >> >> -----Original Message----- >> From: Ray Leaman >> Sent: Nov 29, 2020 9:27 PM >> To: legacy-ornamental-mills@googlegroups.com >> Subject: Re: Motor Driven Rotary Table - Couplings >> >> I'm thinking the pilaster dogs will be good for making some of the >> quarter rounds for grandfather clocks. Could make four at the same time. >> ------------------------------ >> >> On Sun, Nov 29, 2020 at 8:33 PM M.W.Foscue <mwfos...@earthlink.net> >> wrote: >> >>> Bill, >>> That's a useful page if someone has the P.Dogs and is not sure how they >>> are used. >>> If someone looks closely at the photo of the wall in the lower left >>> corner - they can see two pilasters installed. These appear to be fluted >>> and give the appearance of small "columns". Note - they are not a "column" >>> that's been cut vertically down the center. They are a lot "flatter" than >>> that. That's basically what a pilaster is. (Bill, I know you know all >>> this - just sharing it in case someone is not quite sure about them.) >>> Thanks for sharing. >>> Mac >>> ------------------------------ >>> >>> -----Original Message----- >>> From: bulke...@mmnet.com.au >>> Sent: Nov 29, 2020 3:21 PM >>> To: legacy-ornamental-mills@googlegroups.com >>> Subject: RE: Motor Driven Rotary Table - Couplings >>> >>> Just in case you don’t have this page >>> >>> >>> >>> Bill >>> ------------------------------ >>> >>> *From:* legacy-ornamental-mills@googlegroups.com < >>> legacy-ornamental-mills@googlegroups.com> *On Behalf Of *Ray Leaman >>> *Sent:* Monday, 30 November 2020 2:59 AM >>> *To:* legacy-ornamental-mills@googlegroups.com >>> *Subject:* Motor Driven Rotary Table - Couplings >>> >>> >>> >>> The previous line of posts was getting pretty long so I thought I would >>> start a new one on an entry from Curt. >>> >>> >>> >>> Curtis, I found these "jaw couplers" in a bag of items that came with >>> my 1200. You had sent me some info Re; Kaman couplers which I >>> appreciated. As these came with my machine and some are still in the >>> plastic I think these must be original to the legacy. What do you think? >>> I noticed the Kaman had 3 prongs and these only have 2 prongs. Is that an >>> issue? >>> >>> >>> >>> Ray >>> >>> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/legacy-ornamental-mills/1842226517.4964.1606721918543%40wamui-charming.atl.sa.earthlink.net >> <https://groups.google.com/d/msgid/legacy-ornamental-mills/1842226517.4964.1606721918543%40wamui-charming.atl.sa.earthlink.net?utm_medium=email&utm_source=footer> >> . >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/legacy-ornamental-mills/MWHPR13MB0976032490791EACA2C8A1F4B3F50%40MWHPR13MB0976.namprd13.prod.outlook.com >> <https://groups.google.com/d/msgid/legacy-ornamental-mills/MWHPR13MB0976032490791EACA2C8A1F4B3F50%40MWHPR13MB0976.namprd13.prod.outlook.com?utm_medium=email&utm_source=footer> >> . >> > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK_Ppbq3VckG5na9POfkvjcAOKw0mu0EF4qbyH1Az_c%2Bw%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK_Ppbq3VckG5na9POfkvjcAOKw0mu0EF4qbyH1Az_c%2Bw%40mail.gmail.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFpgqtvPu4HCg%2BhU3vfeqeBwFy8VHmzkt1HA7GFJLgyiQ%40mail.gmail.com.
