Hi The only pic of the little Ferrari tractor that I have is.A copy of my avatar on my VW Camper forum.I have taken a pic of it. but can't paste drag and drop.If Anyone wants to see it please email me. Sorry to get too far off the Legacy chat Richard
On Tuesday, December 22, 2020 at 11:43:31 AM UTC timjz...@gmail.com wrote: > They showed an articulating on the web. It looked pretty cool must have > been close the one you may have had? > > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 <(320)%20294-5798> shop > 320-630-2243 <(320)%20630-2243> cell > > > On Tue, Dec 22, 2020 at 3:35 AM Richard Ellis <rchrd....@gmail.com> wrote: > >> Hi Mac >> Mine was an older model it was articulated , had a small hydraulic ram to >> make it pivot in the middle. As far as I can remember a strange gear set up. >> Richard >> >> On Monday, December 21, 2020 at 7:00:38 PM UTC Va Oak wrote: >> >>> Richard, >>> Thanks. I did that, and never could find one called "Artic". >>> Saw a fair number of Ferrari "mini" tractors - but most seemed to be >>> somewhat "modern" - so figured they must be newer models - not one you were >>> referring to. >>> Mac >>> ------------------------------ >>> >>> -----Original Message----- >>> From: Richard Ellis >>> Sent: Dec 21, 2020 1:53 PM >>> To: Legacy Ornamental Mills >>> Subject: Re: Barn find Revo >>> >>> Mac >>> If you just type Ferrari tractors in google search . It was only about >>> 4 foot high. I used it to tow a small grass mower. >>> Richard >>> ------------------------------ >>> >>> On Monday, December 21, 2020 at 6:36:51 PM UTC Va Oak wrote: >>> >>>> Richard, >>>> I can't find a "Ferrari mini artic" tractor on the internet. >>>> Can you provide a link to pics or a site that shows one? >>>> Sounds interesting. Thanks. >>>> Mac >>>> ------------------------------ >>>> >>>> -----Original Message----- >>>> From: Richard Ellis >>>> Sent: Dec 21, 2020 3:47 AM >>>> To: Legacy Ornamental Mills >>>> Subject: Re: Barn find Revo >>>> >>>> Thanks for the replies ,He wants a working Revo. And I don't want any >>>> parts. Tim talking tractors ,I have had Allis -Chalmers model "U" and "M" >>>> good old work horses Also Cletrac crawlers,, Minneapolis Moline .And even >>>> a >>>> Ferrari mini artic. plus loads of others . How I wish I had kept them all >>>> !! I would have been a millionaire >>>> I will tell my friend to offer £100 >>>> Richard >>>> ------------------------------ >>>> >>>> On Sunday, December 20, 2020 at 3:20:48 PM UTC timjz...@gmail.com >>>> wrote: >>>> >>>>> Any LOM is a good LOM. it's like restoration of an old OLIVER tractor. >>>>> It's all worth it in the end. Keep the heritage alive even it's only for >>>>> parts >>>>> ------------------------------ >>>>> >>>>> On Sun, Dec 20, 2020, 9:05 AM 'Curt George' via Legacy Ornamental >>>>> Mills <legacy-orna...@googlegroups.com> wrote: >>>>> >>>>>> Are you sure that lead screw is ruined? >>>>>> >>>>>> If its in as bad shape as you state. offer a few bucks for it. Out >>>>>> side the leadscrew and gears the hole machine only has $30.00 worth of >>>>>> scrap metal in it. If you can get it, a little TLC (Tender Loving Care.) >>>>>> I >>>>>> know you can get it working again. >>>>>> I wish you luck on this one. In the worst case... if you pick it up. >>>>>> there are some parts in the machine that others (or your self) who could >>>>>> use with your Legacy. >>>>>> >>>>>> Good luck. >>>>>> C.A.G. >>>>>> ------------------------------ >>>>>> On Sunday, December 20, 2020, 05:47:50 AM EST, Richard Ellis < >>>>>> rchrd....@gmail.com> wrote: >>>>>> >>>>>> I have a good friend who wants a REVO I know where there is one, in >>>>>> an old barn, but in a very sad state. It is very rusty and has been for >>>>>> a >>>>>> long while. It has a rotary table laying on the floor along with other >>>>>> Revo >>>>>> stuff. It also has a plate holder on the front with a few cutters in it >>>>>> They are also very very rusty. I don't think This sad Revo has been >>>>>> used >>>>>> for about six or more years. >>>>>> *Now my question !!! What is a sensible offer* ,bearing in mind the >>>>>> leadscrew is ruined. And spares are not available here in the U,K, It >>>>>> will >>>>>> need a lot of work to restore it to a good condition. >>>>>> Richard U.K. >>>>>> >>>>> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental...@googlegroups.com. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/legacy-ornamental-mills/0a822836-dd14-4ea7-bd18-b31b6f5a5203n%40googlegroups.com >> >> <https://groups.google.com/d/msgid/legacy-ornamental-mills/0a822836-dd14-4ea7-bd18-b31b6f5a5203n%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/e8ce3f44-11cb-4603-ae6d-e90acac51147n%40googlegroups.com.
