For sure Curt Fun stuff, I did a bunch of V grooves in a piece tonight using your indexing system and my new plates I made.
Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, Jan 23, 2022 at 8:49 PM 'Curt George' via Legacy Ornamental Mills < legacy-ornamental-mills@googlegroups.com> wrote: > Thanks Tim > > I like making designs on projects, the button's, both the ones I've used > made by Magnate, and the buddha bead cutters are nice for buttons. But I > very much also like the diamond hole saws, the diamond dose not cut the > wood it sands it, and or burns the wood leaving round marks that have very > little tare-out, On the larger diamond hole-saws, They can be use by off > setting the cutter so it makes ovals and chain link designs and a lot > more. Lots of fun and So many possibility's for different design elements, > can be made on the Legacy. > > C.A.G. > > On Sunday, January 23, 2022, 09:16:23 PM EST, Tim Ziegler < > timjzieg...@gmail.com> wrote: > > > Looks like you got a ringer Curt lol. > > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 shop > 320-630-2243 cell > > > On Sun, Jan 23, 2022 at 1:45 PM 'Curt George' via Legacy Ornamental Mills < > legacy-ornamental-mills@googlegroups.com> wrote: > > Hello Again everyone. > > Doesn't look good to get back anytime soon. Here are some old photos that > may help? > Not quite what I was talking about, but I think you can see, By playing > with the bead/cutter you can come up with many different designs, all > depending on how you what, In line, Off set, over lapping... there are many > possibility's open to you. > > C.A.G. > > On Sunday, January 23, 2022, 02:31:27 PM EST, 'Curt George' via Legacy > Ornamental Mills <legacy-ornamental-mills@googlegroups.com> wrote: > > > Hello Everyone. > > *ONE quick note to all. * Google is no longer sponsoring "Groups" So > many things are not working as they were. > Its nothing to alarm anyone, but For our New members, and others who, > Watch the group but have not been fully > intergraded into the group. Things are moving much slower then we like. > > I just went to the group page and found some *5 people* pending approval > to the group. (I was not notified that they were waiting.) > NOW for those who have access to the group but have not been given > approval to post, Please do so SOON, It may take time before either Tim K. > or I grant the access to post messages to the group, (Again notice is no > longer being sent to us, stating that you are waiting.) > I'm sorry for any delays you may receive. > > > *I'm going to add this onto this up-date posting of mine,* A question > that was asked to me, on My personal e-mail. which is > curt.geo...@yahoo.com > *Side note:* > *For any reason, Anyone can ask me (or Tim Krause) Questions at our e-mail > addresses, that you may not want the group to know that you asked. (there > is no such thing as a dumb question.)* > *I can and will post those questions under my name, to the group, if need > be. So no one needs to worry about not knowing the answer, or feeling the > imbursements or looking bad for not knowing.* > > *OUR GOAL is to "Help All", So the questions asked, Can help others who > may have the same question in the future.* > > *The question.* > On/about, my roping of the button pattern. > When making a row of pearls/buttons, you need to remember that its not > only the pitch of the rope cut , that you need to think about , but the > Acme screw pitch as well. (Which is 5/8"-4) There are 4 threads per inch. > so when I made my roping of beads, I used my crank handle as a indicator > for me. ONE full rotation of the handle is 1/4", If my button is under a > 1/4" (I used a 6mm last week, which is smaller...) I plunged the router > bit down, to make the bead, then lifted up and rotated the handle one turn, > advancing the spindle and carriage 1/4". then plunging down again, over and > over until I get to the end, or where I plan to stop cutting. > For the others beads, I used the same concept, 2 rotations would be 1/2", > 3 would be 3/4". > > *Now what looks very neat*, Is to cut a rope with the spacing between the > rope (tops upper edge.) that is the same as one of your button cutters. > (Magnate cutters all have a flats on the sides of the button. By using this > flat you can undercut part of your bead, leaving a flat and the button > pronounced ( above the wood) vs like I did with the bead cutters last week, > where the beads were under the surface. > > If I can find some time today I plan to show this process in my detail. > (with photo's.) > > But at this time, I have a lot of work that needs to be done today. (Work > first, then play time, after.) ;-) > > Have a good day everyone. > More to come. ;-) > > C.A.G. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/1757008661.730514.1642966263607%40mail.yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/1757008661.730514.1642966263607%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/960956348.724418.1642967107629%40mail.yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/960956348.724418.1642967107629%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLHunA-OdqwK1MWcnKx2XsUmby%3D1n1ps4TqJN6q9c6OhNg%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLHunA-OdqwK1MWcnKx2XsUmby%3D1n1ps4TqJN6q9c6OhNg%40mail.gmail.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/233284887.780716.1642992547844%40mail.yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/233284887.780716.1642992547844%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGpd3B2%3DjBUnKekZW8Z0Xa1Y6RtMeQaG7S2UAfbZXXeGw%40mail.gmail.com.
