That is super great to hear Denson. We need to tap on the seasoned LOM user's. that's the way we keep this alive and great info goes on without getting lost. Thanks Bill for being so willing to share.
Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Oct 31, 2022 at 9:02 PM 'Denson Ingram' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com> wrote: > Hey Bill I used that method on a 900 yesterday because the chart’s method > and dimensions didn’t work out right. This method does. > Thanks > Denson > > Sent from Denson's iPhone > > > On Oct 31, 2022, at 10:58 AM, bulke...@mmnet.com.au wrote: > > > > There is a way to set a taper without a chart you mount a scrap peace > of timber in the mill and turn 2 diameters on it > > Each at the distance apart that you want the length of your taper to be > the one at the headstock end you mill to the large dia you want > > your taper to be and the other end you mill to the small dia you want > the taper to be put a mark on each so the 2 lines are the exact > > Distance you want the length of the taper to be then lift the tailstock > end till they are both the same distance down lay a strait edge across the > > Liner rails and measure down with a ruler when the 2 are the same > distance your taper will be set. > > > > Bill > > > > -----Original Message----- > > From: legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> On Behalf Of > bulke...@mmnet.com.au > > Sent: Tuesday, 1 November 2022 2:30 AM > > To: legacy-ornamental-mills@googlegroups.com > > Subject: RE: Evolution > > > > Do you have a Evolution mill ? I didn’t think anyone had one very rear > mill I doubt if you will get a taper chart for it but there are taper > charts Here for other model mills > https://lwmcnc.com/cnc-systems/past-models/ornamental-mills/manuals/ > > > > contacting legacy would be the only way to get one if they even made one > if you own a evolution mill did it come with a user manual there should be > a chart in that there usually is in the user manuals > > > > Bill > > > > > > -----Original Message----- > > From: legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> On Behalf Of James Hoerter > > Sent: Monday, 31 October 2022 2:08 PM > > To: legacy-ornamental-mills@googlegroups.com > > Subject: Evolution > > > > Does anyone have a PDF of taper chart for the Evolution Legacy that > will tell me the distance I need to elevate the platform to achieve a given > taper over a given length of the spindle? Send to > jameshoer...@gmail.com. Thanks > > > > Sent from my iPad > > > > -- > > You received this message because you are subscribed to the Google > Groups "Legacy Ornamental Mills" group. > > To unsubscribe from this group and stop receiving emails from it, send > an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/5BB9FDBC-0FF7-429F-B0B2-8500472CC820%40gmail.com > . > > > > -- > > You received this message because you are subscribed to the Google > Groups "Legacy Ornamental Mills" group. > > To unsubscribe from this group and stop receiving emails from it, send > an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/001501d8ed3d%24b0afaa40%24120efec0%24%40mmnet.com.au > . > > > > -- > > You received this message because you are subscribed to the Google > Groups "Legacy Ornamental Mills" group. > > To unsubscribe from this group and stop receiving emails from it, send > an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/001b01d8ed41%249c493450%24d4db9cf0%24%40mmnet.com.au > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/A33662DF-4693-4497-ADCE-AA99B0CBA53D%40yahoo.com > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFR6uuf4Zt%2BRyqSx2HAO1-3jSa2cjFLO83x_SMbTgsMeQ%40mail.gmail.com.
