I understand curt I have the same problem but in reverse its too hot to work out in the shop by day and by night insects drive you insane not to mention
In the summer I have to check the shop for poisonous snakes before I start they get a little upset if I run over one lol, after all our brown snakes venom is the second most toxic in the world not good if you get bit. Bill From: 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com> Sent: Tuesday, January 16, 2024 12:44 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Oval jig testing I promise that when I can make a video you will be the first to know. And it will be as soon as I can. I have a few mod.'s that I want to do, and the temperatures need to be a little bit wormer . (camera crews can be Fickled. )(Which means, I have to get one of my kids to film it.) ;-) C.A.G. On Monday, January 15, 2024 at 07:27:54 PM EST, <bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> > wrote: Great I’m really looking forward to it Bill From: 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > Sent: Tuesday, January 16, 2024 11:18 AM To: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> Subject: Re: Oval jig testing Most likely next weekend??? We will see. C.A.G. On Monday, January 15, 2024 at 07:14:45 PM EST, <bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> > wrote: Very nice curt a video showing it working will show all exactly what your explaining Bill From: 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > Sent: Tuesday, January 16, 2024 7:16 AM To: 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > Subject: Re: Oval jig testing Woops. part of this message did not show up... Here is the hole message. (second try!) Hello Everyone. It's -5 outside today. (Thanks Tim, for sending Bill some cold air, it hit my area in its way to Auz. ) ;-p Since my shop is un-heated, (I use a propane heater to heat the shop when I'm working, But today its just to cold to go out there and try to heat the shop.) This is a reply that I gave to a private e-mail Explaining what I was doing/ how this jig works. I think everyone will enjoy this info. The Planetary gear system is the concept that I am using to make this jig work. The "Sun" Gear is pinned to the tables supports, (It dose not move with the table.) The Planet gear is fixed to the table. so it moves around the sun gear when the table turns. the planet gear has a fixed pin on it. so as it moves the arm moves the table. thus making an oval as the table turns. I am using my Legacy/overhead router for the cutting. (at this time.) I Hope the photo's help explain what is happening here? photo 1 shows the "Sun" gear lifted up, a post, is running through the ball bearing center. (its pined under the table, to keep it form moving .) photo 2 shows the linkage. (as the table moves the planate gear rotates moving the pin, making the table move back and forth as the planate turns around the sun gear.) Photo3 shows the planate gear/pin and table with linear rails. Photo's 4&5 show the over all set-up on my Legacy (Ornamental Mill.) C.A.G. On Monday, January 15, 2024 at 03:02:54 PM EST, 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > wrote: Hello Everyone. It's -5 outside today. (thanks Tim, for sending Bill some cold air, it hit my area in its way to Auz. ) ;-p Since my shop is un-heated, (I use a propane heater to heat the shop when I'm working, But today its just to cold to go out there and try to heat the shop.) This is a reply that I gave to a private e-mail Explaining what I was doing/ how this jig works. I think everyone will enjoy this info. The Planetary gear system is the concept that I am using to make this jig work. The "Sun" Gear is pinned to the tables supports, (It dose not move with the table.) The Planet gear is fixed to the table. so it moves around the sun gear when the table turns. the planet gear has a fixed pin on it. so as it moves the arm moves the table. thus making an oval as the table turns. I am using my Legacy/overhead router for the cutting. (at this time.) I Hope the photo's help explain what is happening here? photo 1 shows the sun gear lifted up running through the ball bearing center. (its pinning under the table.) photo 2 shows the linkage. Photo3 shows the planate gear/pin and table with linear rails. Photo's 4&5 show the over all set-up on my Legacy (Ornamental Mill.) C.A.G. On Sunday, January 14, 2024 at 09:29:28 PM EST, Curt George <curt.geo...@yahoo.com <mailto:curt.geo...@yahoo.com> > wrote: Hello Frank. The planetary gear has a is fixed pin at this min. But I will be able to make it adjustable latter. At this time there is a 2" off-set. The table is disposable, there are only 4 screw holding it down onto the slides. I am using linear slides for the table. (in two photo's I used drawer slide they worked but they got in the way of my Legacy side rails. so I replaced them.) If all goes well, I will be making an oval picture frame, and latter some small bowls. talk to you and everyone more latter. C.A.G. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/735714525.996038.1705348903408%40mail.yahoo.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/735714525.996038.1705348903408%40mail.yahoo.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/1448721690.1003398.1705349747143%40mail.yahoo.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/1448721690.1003398.1705349747143%40mail.yahoo.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/003c01da4810%24ff3263e0%24fd972ba0%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/003c01da4810%24ff3263e0%24fd972ba0%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/3003881.1056652.1705364266233%40mail.yahoo.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/3003881.1056652.1705364266233%40mail.yahoo.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/004e01da4812%24d425a8e0%247c70faa0%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/004e01da4812%24d425a8e0%247c70faa0%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/1662857013.1069705.1705369413129%40mail.yahoo.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/1662857013.1069705.1705369413129%40mail.yahoo.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000601da4825%240e6ceba0%242b46c2e0%24%40mmnet.com.au.