Great update for all of us Curt. Yes we are super excited to see this becoming a everyday attachment at some point. Keep working on it. Looking for more updates. Put that coat and cap on and lets do it lol.
Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty Ziegler Laser Worx LLC 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Jan 15, 2024 at 2:02 PM 'Curt George' via Legacy Ornamental Mills < legacy-ornamental-mills@googlegroups.com> wrote: > Hello Everyone. > It's -5 outside today. (thanks Tim, for sending Bill some cold air, it hit > my area in its way to Auz. ) ;-p > Since my shop is un-heated, (I use a propane heater to heat the shop when > I'm working, But today > its just to cold to go out there and try to heat the shop.) > > This is a reply that I gave to a private e-mail Explaining what I was > doing/ how this jig works. > I think everyone will enjoy this info. > > > The Planetary gear system is the concept that I am using to make this jig > work. > The "Sun" Gear is pinned to the tables supports, (It dose not move with > the table.) > The Planet gear is fixed to the table. so it moves around the sun gear > when the table turns. > the planet gear has a fixed pin on it. so as it moves the arm moves the > table. thus making an > oval as the table turns. I am using my Legacy/overhead router for the > cutting. (at this time.) > > I Hope the photo's help explain what is happening here? > photo 1 shows the sun gear lifted up running through the ball bearing > center. (its pinning under the table.) > photo 2 shows the linkage. > Photo3 shows the planate gear/pin and table with linear rails. > Photo's 4&5 show the over all set-up on my Legacy (Ornamental Mill.) > > C.A.G. > On Sunday, January 14, 2024 at 09:29:28 PM EST, Curt George < > curt.geo...@yahoo.com> wrote: > > > Hello Frank. > The planetary gear has a is fixed pin at this min. But I will be able to > make it adjustable latter. > > At this time there is a 2" off-set. > The table is disposable, there are only 4 screw holding it down onto the > slides. > I am using linear slides for the table. (in two photo's I used drawer > slide they worked but they got in the way of my Legacy side rails. so I > replaced them.) > > If all goes well, I will be making an oval picture frame, and latter some > small bowls. > > talk to you and everyone more latter. > > C.A.G. > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/735714525.996038.1705348903408%40mail.yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/735714525.996038.1705348903408%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEHmyTFp6gg-tGLaCGbhXfZ-Rv204ZPdfTG_0MvyAMDQw%40mail.gmail.com.
