Hey Guys!
Bill I have a way to make this chatter wave 100% every time. but it involves
another jig to make it work. What I did the first time is supper Kool, but Its
not easy to get the results prefect every time. I called this cut a chatter
cut, mainly due to that is exactly what is happening, the route bit
chatters/bounces over the wood as it is cutting.There are a number of variables
that are needed to make the Chatter cut work on the Legacy at this time it is
not an exact science . (those variables are, speed of cut/RPM of the bit, depth
of cut from the side/Y axis , and Speed of the motor drive/carriage movement.
all have to be the same, to get the good results. If one is off the cut will
not be consistent.)
C.A.G.
On Friday, March 1, 2024 at 06:23:14 PM EST, <bulke...@mmnet.com.au> wrote:
<!--#yiv0435932390 filtered {}#yiv0435932390 filtered {}#yiv0435932390
filtered {}#yiv0435932390 filtered {}#yiv0435932390 p.yiv0435932390MsoNormal,
#yiv0435932390 li.yiv0435932390MsoNormal, #yiv0435932390
div.yiv0435932390MsoNormal {margin:0cm;font-size:12.0pt;font-family:"Aptos",
sans-serif;}#yiv0435932390 a:link, #yiv0435932390
span.yiv0435932390MsoHyperlink
{color:blue;text-decoration:underline;}#yiv0435932390 p.yiv0435932390msonormal,
#yiv0435932390 li.yiv0435932390msonormal, #yiv0435932390
div.yiv0435932390msonormal
{margin-right:0cm;margin-left:0cm;font-size:12.0pt;font-family:"Aptos",
sans-serif;}#yiv0435932390 p.yiv0435932390msonormal1, #yiv0435932390
li.yiv0435932390msonormal1, #yiv0435932390 div.yiv0435932390msonormal1
{margin:0cm;font-size:12.0pt;font-family:"Aptos", sans-serif;}#yiv0435932390
p.yiv0435932390yahoo-quoted-begin1, #yiv0435932390
li.yiv0435932390yahoo-quoted-begin1, #yiv0435932390
div.yiv0435932390yahoo-quoted-begin1
{margin-right:0cm;margin-left:0cm;font-size:12.0pt;font-family:"Aptos",
sans-serif;}#yiv0435932390 span.yiv0435932390EmailStyle32 {font-family:"Arial",
sans-serif;color:windowtext;}#yiv0435932390 .yiv0435932390MsoChpDefault
{font-size:10.0pt;}#yiv0435932390 filtered {}#yiv0435932390
div.yiv0435932390WordSection1 {}-->
Well however you did it I think it needs more research I think it’s a very
interesting look
Bill
From: 'Curt George' via Legacy Ornamental Mills
<legacy-ornamental-mills@googlegroups.com>
Sent: Saturday, March 2, 2024 1:43 AM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: Feb 5 bone turnings
Hello Bill
The chatter wave was cut form the side of the work piece, I used the clime
cutting method, (the router bit is spinning like a car tire on wet pavement)
Sadly I do not remember the pitch or speed I used at this time.
What I do remember is the chatter happened on the first cut, I liked the look,
so I repeated all the cut the exact way to repeat this process.
Here are some more Wave' y cuts that I have made.
C.A.G.
On Friday, March 1, 2024 at 03:21:38 AM EST, <bulke...@mmnet.com.au> wrote:
Nice chatter wave curt what pitch did you set the mill at? And what wave width
did you set the attachment at? also how many starts? and last what router bit
did you use to side cut that wave? And what was the blank size? Lots of
questions I know lol sorry
Bill
From: 'Curt George' via Legacy Ornamental Mills
<legacy-ornamental-mills@googlegroups.com>
Sent: Friday, March 1, 2024 4:25 PM
To: 'parr...@aol.com' via Legacy Ornamental Mills
<legacy-ornamental-mills@googlegroups.com>
Subject: Re: Feb 5 bone turnings
Hello Everyone. (just got home form work.)
Thank you all for the kind words.
Using and Making the Wave attachment is not all that hard to do.
I too enjoy the look of the waves, in wood as well as in my bone turnings.
If anyone would like to know more, We can open a posting on the process of
making
one. With Tim K. Bill, and my self,(who have all made our own versions.) as
well as a few
others in the group who own the wave attachment, I'm sure anyone in the group
could make there
own. The concept of how they work, as well as the simple construction it takes
to
make a attachment. Is pretty easy.
Just let me know what you all think?
Here are a few photo's of both, works and attachment.
C.A.G.
On Thursday, February 29, 2024 at 01:48:19 PM EST, 'parr...@aol.com' via Legacy
Ornamental Mills <legacy-ornamental-mills@googlegroups.com> wrote:
Beautiful
Sent from the all new AOL app for iOS
On Thursday, February 29, 2024, 8:44 AM, 'Curt George' via Legacy Ornamental
Mills <legacy-ornamental-mills@googlegroups.com> wrote:
Good morning everyone
Tim here is the photos you asked for. I hope these photo work for you?
for some reason taking photo's of these bone handles, just don't quite look the
same as they do by eye. The cut is .250 of an inch deep (appx. the same depth
as a piece of paper) the wave off-set is 1/8" with a 3" pitch.
I hope this helps?
Have a good day.
C.A.G.
On Thursday, February 29, 2024 at 06:35:29 AM EST, Tim Ziegler
<timjzieg...@gmail.com> wrote:
Hey Curt,
Those are some extremely nice looking bone handles.
Thanks for sharing them. You are truely the Bone turning Master.
Can you take a close up of the one you used the wave attachment
on? I would like to zoom in on the pattern a little bit closer.
Great work as always.
Kind Regards,
Timothy J. Ziegler
Ziegler WoodWork & Specialty
Ziegler Laser Worx LLC
14171 160th Ave.
Foreston MN 56330
320-294-5798 shop
320-630-2243 cell
On Wed, Feb 28, 2024 at 11:45 PM 'Curt George' via Legacy Ornamental Mills
<legacy-ornamental-mills@googlegroups.com> wrote:
Hello Everyone. (Just got home form work.)
Here are some of my latest turnings.
I am really having a lot of fun with my Legacy.
Any question or comments are, as always welcome.
I am learning new tricks that are really helping me achieve
my personal best. ;-)
C.A.G.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/253088644.1267098.1709185539973%40mail.yahoo.com.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLHQRoGuHokz28RU2GK7saH_8hn-aZYodDe6%3DGOfWoOjVg%40mail.gmail.com.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/414358743.1323126.1709214276991%40mail.yahoo.com.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/491761846.1954023.1709232490150%40mail.yahoo.com.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/92952494.1547040.1709270730920%40mail.yahoo.com.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/000001da6bb1%2470de9630%24529bc290%24%40mmnet.com.au.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/1209459791.175860.1709304201888%40mail.yahoo.com.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/000401da6c2f%2469cb3a00%243d61ae00%24%40mmnet.com.au.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/1402340879.1795955.1709357552834%40mail.yahoo.com.
