Thank you once again for that., shall keep that in mind This group is so helpful and I appreciate the time you give Regards Gwen
On Fri, Aug 31, 2018 at 1:40 PM Leon Chapman <chap...@gmail.com> wrote: > You need to run Windows in the isolated mode from the Mac side. Then, the > file locations for Legacy are just like a standard Windows only machine. > > If you do not isolate Windows from the Mac side, Legacy will try to find > files on a network and you will have problems. > > Sent from my iPhone > Leon Chapman > chap...@gmail.com > 623-271-1206 <(623)%20271-1206> > > On Aug 30, 2018, at 5:37 PM, Noddie <7thwav...@gmail.com> wrote: > > That sounds really good would you mind clarifying the following for me > (Virtual Machine > Configure… > Options > Security > check on Isolate Mac > from Windows)I > and do I need to go back in after installation and reverse these steps > above? or leave them as they are > Many thanks > Cheers > > On Fri, Aug 31, 2018 at 7:02 AM Leon Chapman <chap...@gmail.com> wrote: > >> Ok, I have a new update on the Legacy 9 install on Parallels 14. >> >> On my iMac which did not have Legacy 9 GR or Legacy 9 Beta installed -- >> >> I downgraded from Parallels 14 to 13.3.2 – you just download their >> install file for v13.3.2 and reinstall over v14. >> >> Using Parallels 13.3.2: >> 1. I installed Legacy GR - 9.0.0.226 >> a. It again stopped about 92% thru the install process and the process >> became unresponsive >> b. I left the installer process open for about 10 minutes, and it finally >> finished the install. >> c. Legacy 9 GR is running just fine under Parallels 14.0.0. >> >> Next, I reinstalled Parallels 14.0.0 from scratch over Parallels 13.3.2 >> 1. I then installed the Legacy Beta – 9.0.0.253 >> a. The install went perfect – no delays during install >> b. Legacy Beta 9.0.0.253 is running just fine. >> >> I then went to my MacBook Pro – It had Parallels 13.3.2 installed and had >> Legacy Beta installed. >> 1. I upgraded to Parallels 14.0.0 >> 2. This Windows VM already had Legacy 9 Beta 9.0.0.253 installed >> 3. Legacy is running just fine. >> >> Bottom line, it is ok for everyone to install Parallels 14.0.0 if they >> choose. >> Legacy should install and run just fine, just give it some time to finish >> the install process if it stops during the install. >> >> Another side note: Be sure to Isolate Windows from the Mac or you will >> have problems with file locations that act like you are running Legacy on a >> network and it cannot find file locations. Here is how to Isolate Windows >> from Mac to exclude Mac OS X influence: >> >> (Virtual Machine > Configure… > Options > Security > check on Isolate Mac >> from Windows) >> >> If you have problems with Legacy install, here is a Parallels Help page: >> https://kb.parallels.com/112983 >> >> Good luck with using Parallels 14.0.0 on the Mac! >> ___ >> Leon Chapman >> chap...@gmail.com >> ----- >> -- >> >> LegacyUserGroup mailing list >> LegacyUserGroup@legacyusers.com >> To manage your subscription and unsubscribe >> http://legacyusers.com/mailman/listinfo/legacyusergroup_legacyusers.com >> Archives at: >> http://www.mail-archive.com/legacyusergroup@legacyusers.com/ >> > -- > > LegacyUserGroup mailing list > LegacyUserGroup@legacyusers.com > To manage your subscription and unsubscribe > http://legacyusers.com/mailman/listinfo/legacyusergroup_legacyusers.com > Archives at: > http://www.mail-archive.com/legacyusergroup@legacyusers.com/ > > -- > > LegacyUserGroup mailing list > LegacyUserGroup@legacyusers.com > To manage your subscription and unsubscribe > http://legacyusers.com/mailman/listinfo/legacyusergroup_legacyusers.com > Archives at: > http://www.mail-archive.com/legacyusergroup@legacyusers.com/ >
-- LegacyUserGroup mailing list LegacyUserGroup@legacyusers.com To manage your subscription and unsubscribe http://legacyusers.com/mailman/listinfo/legacyusergroup_legacyusers.com Archives at: http://www.mail-archive.com/legacyusergroup@legacyusers.com/
