I am attempting to setup a Guest Lan on zVM 4.3 on a z800. I have one Linux machine, lnxrtr1, up and running with a CTC connection to the zVM TCPIP virtual machine. My goal is to have the lnxrtr1 linux machine act be a router for my Guest Lan. I am now trying to get lnxrtr1 to communicate to the Guest Lan. I have defined the LAN as follows:
cp q lan qdiolan2 details LAN SYSTEM QDIOLAN2 Type: QDIO Active: 1 MAXCONN: INFINITE PERSISTENT RESTRICTED MFS: 8192 ACCOUNTING: OFF Authorized userids: LNXRTR1 SYSTEM Adapter Owner: LNXRTR1 NIC: 7000 Name: BEARS Ready; T=0.01/0.01 17:34:01 In lnxrtr1, I have defined the NIC and have coupled it to the LAN, as shown with the following query commands: CP Q NIC DETAILS Adapter 7000 Type: QDIO Name: BEARS Devices: 3 Port 0 MAC: 00-04-AC-00-00-00 LAN: SYSTEM QDIOLAN2 MFS: 8192 RX Packets: 0 Discarded: 0 Errors: 0 TX Packets: 0 Discarded: 0 Errors: 0 RX Bytes: 0 TX Bytes: 0 Connection Name: HALLOLE State: Session Established Device: 7000 Unit: 000 Role: CTL-READ Device: 7001 Unit: 001 Role: CTL-WRITE Device: 7002 Unit: 002 Role: DATA CP Q V 7000 OSA 7000 ON NIC 7000 UNIT 000 SUBCHANNEL = 0015 7000 QDIO-ELIGIBLE Now the linux setup information: My /etc/chandev.conf file in lnxrtr1 contains the following: ctc0,0x7100,0x7101 add_parms 0x10,0x7000,0x7002,portname:BEARS qeth1,0x7000,0x7001,0x7002 My /etc/modules.conf file in lnxrtr1 contains the following: # alias eth0 lcs #alias eth1 off alias eth1 qeth alias tr0 off I load qdio and qeth as shown below: lnxrtr1:~ # insmod qdio Using /lib/modules/2.4.17/kernel/drivers/s390/net/qdio.o lnxrtr1:~ # insmod qeth Using /lib/modules/2.4.17/kernel/drivers/s390/net/qeth.o lnxrtr1:~ # lsmod Module Size Used by qeth 138992 0 (unused) qdio 40128 1 [qeth] ipv6 249664 -1 (autoclean) ctc 53808 1 (autoclean) fsm 1984 0 (autoclean) [ctc] lvm-mod 47280 0 (autoclean) My current ip settings: lnxrtr1:~ # ifconfig ctc0 Link encap:Serial Line IP inet addr:147.185.179.2 P-t-P:147.185.2.158 Mask:255.255.255.128 UP POINTOPOINT RUNNING NOARP MTU:8992 Metric:1 RX packets:465 errors:0 dropped:0 overruns:0 frame:0 TX packets:422 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:53351 (52.1 Kb) TX bytes:53154 (51.9 Kb) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) When I define the IP configuration for the eth1 with the following command, I lose all IP connectivity and there are no messages in the TN3270 window. lnxrtr1:~ # ifconfig eth1 147.185.179.65 >From the TC3270 window I can run ifconfig and get the following: ifconfig ctc0 Link encap:Serial Line IP inet addr:147.185.179.2 P-t-P:147.185.2.158 Mask:255.255.255.128 UP POINTOPOINT RUNNING NOARP MTU:8992 Metric:1 RX packets:1438 errors:0 dropped:0 overruns:0 frame:0 TX packets:1413 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:162163 (158.3 Kb) TX bytes:245515 (239.7 Kb) eth1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:147.185.179.65 Mask:255.255.0.0 inet6 addr: fe80::200:ff:fe00:0/10 Scope:Link UP RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:14376 (14.0 Kb) Interrupt:21 If I bring eth1 down from the TN3270 window I can logon on with putty. I have used presentations from Share, presentations from IBM's zVM/zOS Technical Conference, IBM's Large Scale Linux Deployment Redbook and the Device Drivers and Installation Commands Manual as reference in this effort. If anyone can see what I did wrong please let me know, I have been fighing this for days. Your help is greatly appreciated. I apologize for the length of this email. Thomas L. Geyer Email:[EMAIL PROTECTED] Phone:(330) 471-2073 Fax:(330) 471-4034 ********************************************************************** This message and any attachments are intended for the individual or entity named above. If you are not the intended recipient, please do not forward, copy, print, use or disclose this communication to others; also please notify the sender by replying to this message, and then delete it from your system. The Timken Company **********************************************************************