Perhaps I'm misunderstanding here.
Diald has no way of knowing when you have stopped using Netscape. It will
use the exact same timeout values for traffic no matter if Netscape is open
or closed.
If you want to immediately shut down the link after you finish then you need
to manually close it. The easiest way to do this is will a
control/monitoring program such as dctrl (think that's spelled right not at
my linux box right now) which comes with diald (in the source packages, I
don't think folks have added it in the binary rpms) or dialmon.
[I prefer the dialmon interface but both will work well in Xwindows and
dialmon adds some additional configuration that you have to deal with.]
Since you are browsing on the same machine that is running diald then you
can simply echo down to a diald control pipe.
add the line 'fifo /etc/diald.ctl' to your diald.conf file. Then you can
'echo down > /etc/diald.ctl' to shut down the connection whenever you want
to. (you can also echo any other command to the pipe to control the
connection.)
dctrl or dialmon is much handier in Xwindows. echo can always be used and
is the easiest solution if you spend much time in console mode. [Xwindows
on my 486 with 4meg mem is a joke.]
Hope this helps,
Lourdes
> -----Original Message-----
> I shall be grateful for any advice that will help me to resolve the
> problem that I am having with disconnecting once I have closed down
> Netscape (4.07). Disconnection can take some three minutes.
>
> I have installed diald on a 90 MHz Pentium, running SuSE-6.2 and
> kernel version 2.2.13. It is a standalone machine, with no net card.
>
> My ISP uses static addresses. When configuring diald, I have used
> dummy addreses for establishing the link, as will be seen from the
> configuration details that follow.
>
> The /var/log/messages file that appears below was generated
> by invoking the diald "debug" option. I'm sorry that this is rather
> lengthy, but as I'm new to diald I am not sure which items might point
> to the cause of the problem! The configuration files are
> also appended.
>
> 1. /var/log/messages file
> -------------------------
>
> Dec 8 16:16:26 syslogd 1.3-3: restart.
> Dec 8 16:16:26 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:16:27 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:16:27 kernel: Serial driver version 4.27 with no serial
> options enabled
> Dec 8 16:16:27 kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
> Dec 8 16:16:27 kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
> Dec 8 16:16:28 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:16:32 last message repeated 4 times
> Dec 8 16:16:33 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:16:38 last message repeated 5 times
> Dec 8 16:16:39 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:17:09 last message repeated 30 times
> Dec 8 16:17:10 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:17:11 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:17:12 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:17:43 last message repeated 31 times
> Dec 8 16:18:01 last message repeated 18 times
> Dec 8 16:18:02 diald[48]: filter accepted rule 22 proto 134645008
> len 62 packet
> 192.168.0.1,1024 => <DNS address>,53
> Dec 8 16:18:02 diald[48]: Trigger: udp 192.168.0.1/1024
> <DNS address>/53
> Dec 8 16:18:02 diald[48]: new state CONNECT action 0x8051ed0
> timeout 60
> Dec 8 16:18:02 diald[48]: Calling site 192.168.0.2
> Dec 8 16:18:03 diald[48]: running '/usr/sbin/chat -f
> /etc/ppp/peers/chat-myISP'
> Dec 8 16:18:03 diald[48]: --- tick --- state 1 block 0
> state_timeout 59
> Dec 8 16:18:04 diald[48]: --- tick --- state 1 block 0
> state_timeout 58
> Dec 8 16:18:05 diald[48]: --- tick --- state 1 block 0
> state_timeout 57
> Dec 8 16:18:06 diald[48]: --- tick --- state 1 block 0
> state_timeout 56
> Dec 8 16:18:07 diald[48]: filter accepted rule 22 proto 134645008
> len 62 packet
> 192.168.0.1,1024 => <DNS address>,53
> Dec 8 16:18:07 diald[48]: --- tick --- state 1 block 0
> state_timeout 55
> Dec 8 16:18:08 diald[48]: --- tick --- state 1 block 0
> state_timeout 54
> Dec 8 16:18:09 diald[48]: --- tick --- state 1 block 0
> state_timeout 53
> Dec 8 16:18:10 diald[48]: --- tick --- state 1 block 0
> state_timeout 52
> Dec 8 16:18:11 diald[48]: --- tick --- state 1 block 0
> state_timeout 51
> Dec 8 16:18:12 diald[48]: filter accepted rule 22 proto 134645008
> len 62 packet
> 192.168.0.1,1024 => <DNS address>,53
>
> <and so on, down to:>
>
> Dec 8 16:18:34 diald[48]: --- tick --- state 1 block 0
> state_timeout 28
> Dec 8 16:18:35 diald[48]: SIGCHLD[4]: pid 230 dial, status 0
> Dec 8 16:18:35 diald[48]: new state START_LINK action 0x8052200
> timeout 60
> Dec 8 16:18:35 diald[48]: Connected to site 192.168.0.2
> Dec 8 16:18:35 diald[48]: Running pppd (pid = 231).
> Dec 8 16:18:35 diald[231]: Running pppd: /usr/sbin/pppd
> -defaultroute -detach modem crtscts
> mtu 1500 mru 1500 netmask 255.255.255.255
> name <host name>
> Dec 8 16:18:35 diald[48]: --- tick --- state 4 block 0
> state_timeout 59
> Dec 8 16:18:35 kernel: PPP: version 2.3.7 (demand dialling)
> Dec 8 16:18:35 kernel: PPP line discipline registered.
> Dec 8 16:18:35 kernel: registered device ppp0
> Dec 8 16:18:35 pppd[231]: pppd 2.3.9 started by root, uid 0
> Dec 8 16:18:35 pppd[231]: Using interface ppp0
> Dec 8 16:18:35 pppd[231]: Connect: ppp0 <--> /dev/ttyS0
> Dec 8 16:18:36 diald[48]: --- tick --- state 4 block 0
> state_timeout 58
> Dec 8 16:18:37 diald[48]: --- tick --- state 4 block 0
> state_timeout 57
> Dec 8 16:18:38 diald[48]: --- tick --- state 4 block 0
> state_timeout 56
> Dec 8 16:18:39 kernel: PPP BSD Compression module registered
> Dec 8 16:18:39 kernel: PPP Deflate Compression module registered
> Dec 8 16:18:39 pppd[231]: local IP address <local address>
> Dec 8 16:18:39 pppd[231]: remote IP address <remote address>
> Dec 8 16:18:39 diald[48]: --- tick --- state 4 block 0
> state_timeout 55
> Dec 8 16:18:39 diald[48]: New addresses: local <local address>,
> remote <remote address>, broadcast 0.0.0.0
> Dec 8 16:18:39 diald[48]: running '/sbin/ifconfig ppp0
> <local address> pointopoint
> <remote address> broadcast 0.0.0.0
> netmask 255.255.255.255 metric 0
> mtu 1500 up'
> Dec 8 16:18:39 diald[48]: start ppp0: SIOCSIFMETRIC: Operation not
> supported
> Dec 8 16:18:39 diald[48]: SIGCHLD[5]: pid 238 system, status 256
> Dec 8 16:18:39 diald[48]: start ppp0: Establishing routes for ppp0
> Dec 8 16:18:39 diald[48]: running '/sbin/route add <remote address>
> metric 0 dev ppp0'
> Dec 8 16:18:40 diald[48]: SIGCHLD[6]: pid 239 system, status 0
> Dec 8 16:18:40 diald[48]: running '/sbin/route add default metric 0
> netmask 0.0.0.0 dev ppp0'
> Dec 8 16:18:40 diald[48]: SIGCHLD[7]: pid 242 system, status 0
> Dec 8 16:18:40 diald[48]: stop tap0: Removing routes for tap0
> Dec 8 16:18:40 diald[48]: running '/sbin/route del default metric 0
> netmask 0.0.0.0 dev tap0'
> Dec 8 16:18:40 diald[48]: SIGCHLD[8]: pid 243 system, status 0
> Dec 8 16:18:40 diald[48]: running '/sbin/ifconfig tap0 down'
> Dec 8 16:18:40 diald[48]: SIGCHLD[9]: pid 244 system, status 0
> Dec 8 16:18:40 diald[48]: new state UP action 0x8052390 timeout 120
> Dec 8 16:18:40 diald[48]: Changed snoop device to ppp0
> Dec 8 16:18:40 diald[48]: --- tick --- state 7 block 0
> state_timeout 119
> Dec 8 16:18:41 diald[48]: --- tick --- state 7 block 0
> state_timeout 118
> Dec 8 16:18:42 diald[48]: filter accepted rule 22 proto 134645008
> len 62 packet
> <local address>,1024 => <DNS address>,53
> Dec 8 16:18:42 diald[48]: --- tick --- state 7 block 0
> state_timeout -1
> Dec 8 16:18:42 diald[48]: filter accepted rule 23 proto 134645008
> len 442 packet
> <DNS address>,53 => <local address>,1024
> Dec 8 16:18:42 diald[48]: filter accepted rule 22 proto 134645008
> len 62 packet
> <local address>,1024 => <DNS address>,53
> Dec 8 16:18:43 diald[48]: filter accepted rule 23 proto 134645008
> len 442 packet
> <DNS address>,53 => <local address>,1024
> Dec 8 16:18:43 diald[48]: --- tick --- state 7 block 0
> state_timeout -1
> Dec 8 16:18:45 last message repeated 2 times
>
> <and so on, down to>
>
> Dec 8 16:19:07 diald[48]: --- tick --- state 7 block 0
> state_timeout -1
> Dec 8 16:19:22 last message repeated 15 times
> Dec 8 16:19:22 diald[48]: Closing down idle link.
> Dec 8 16:19:22 diald[48]: running '/sbin/ifconfig tap0 192.168.0.1
> pointopoint 192.168.0.2 broadcast 0.0.0.0
> netmask 255.255.255.255 metric 0
> mtu 1500 up'
> Dec 8 16:19:22 diald[48]: start tap0: SIOCSIFMETRIC: Operation not
> supported
> Dec 8 16:19:22 diald[48]: SIGCHLD[10]: pid 246 system, status 256
> Dec 8 16:19:22 diald[48]: start tap0: Establishing routes for tap0
> Dec 8 16:19:22 diald[48]: running '/sbin/route add 192.168.0.2
> metric 0 dev tap0'
> Dec 8 16:19:22 diald[48]: SIGCHLD[11]: pid 247 system, status 0
> Dec 8 16:19:22 diald[48]: running '/sbin/route add default metric 0
> netmask 0.0.0.0 dev tap0'
> Dec 8 16:19:22 diald[48]: SIGCHLD[12]: pid 248 system, status 0
> Dec 8 16:19:22 diald[48]: stop ppp0: Removing routes for ppp0
> Dec 8 16:19:22 diald[48]: running '/sbin/route del default metric 0
> netmask 0.0.0.0 dev ppp0'
> Dec 8 16:19:22 diald[48]: SIGCHLD[13]: pid 249 system, status 0
> Dec 8 16:19:22 diald[48]: running '/sbin/ifconfig ppp0 down'
> Dec 8 16:19:22 diald[48]: SIGCHLD[14]: pid 250 system, status 0
> Dec 8 16:19:22 diald[48]: Closed fwdfd
> Dec 8 16:19:22 diald[48]: Changed snoop device to tap0
> Dec 8 16:19:22 diald[48]: new state STOP_LINK action 0x8052330
> timeout 60
> Dec 8 16:19:22 pppd[231]: Terminating on signal 2.
> Dec 8 16:19:23 pppd[231]: Connection terminated.
> Dec 8 16:19:23 pppd[231]: Connect time 0.8 minutes.
> Dec 8 16:19:23 pppd[231]: Sent 689 bytes, received 1373 bytes.
> Dec 8 16:19:23 diald[48]: SIGCHLD[15]: pid 231 link, status 1280
> Dec 8 16:19:23 diald[48]: running '/sbin/ifconfig tap0 192.168.0.1
> pointopoint 192.168.0.2 broadcast 0.0.0.0
> netmask 255.255.255.255 metric 0
> mtu 1500 up'
> Dec 8 16:19:23 pppd[231]: Exit.
> Dec 8 16:19:23 diald[48]: start tap0: SIOCSIFMETRIC: Operation not
> supported
> Dec 8 16:19:23 diald[48]: SIGCHLD[16]: pid 255 system, status 256
> Dec 8 16:19:23 diald[48]: start tap0: Establishing routes for tap0
> Dec 8 16:19:23 diald[48]: running '/sbin/route add 192.168.0.2
> metric 0 dev tap0'
> Dec 8 16:19:23 diald[48]: start tap0: SIOCADDRT: File exists
> Dec 8 16:19:23 diald[48]: SIGCHLD[17]: pid 256 system, status 1792
> Dec 8 16:19:23 diald[48]: running '/sbin/route add default metric 0
> netmask 0.0.0.0 dev tap0'
> Dec 8 16:19:23 diald[48]: start tap0: SIOCADDRT: File exists
> Dec 8 16:19:23 diald[48]: SIGCHLD[18]: pid 257 system, status 1792
> Dec 8 16:19:23 diald[48]: new state DISCONNECT action 0x8052660
> timeout 60
> Dec 8 16:19:23 diald[48]: new state CLOSE action 0x80526f0
> timeout -1
> Dec 8 16:19:23 diald[48]: Closing /dev/ttyS0
> Dec 8 16:19:24 diald[48]: Delaying 30 seconds before clear to dial.
> Dec 8 16:19:24 diald[48]: --- tick --- state 9 block 0
> state_timeout 29
>
> <down to>
>
> Dec 8 16:19:30 diald[48]: --- tick --- state 9 block 0
> state_timeout 23
> Dec 8 16:19:31 diald[48]: filter accepted rule 1 proto tcp len 60
> seq 7f588ae9 ack 0 flags
> SYN packet 192.168.0.1,1024 =>
> 208.216.181.15,80
> Dec 8 16:19:31 diald[48]: Trigger: tcp 192.168.0.1/1024
> 208.216.181.15/80
> Dec 8 16:19:31 diald[48]: --- tick --- state 9 block 0
> state_timeout 22
> Dec 8 16:19:31 kernel: tcp_v4_rebuild_header(): shifting sk->saddr
> from <local address> to 192.168.0.1
> Dec 8 16:19:32 diald[48]: --- tick --- state 9 block 0
> state_timeout 21
>
> <down to>
>
> Dec 8 16:19:53 diald[48]: --- tick --- state 9 block 0
> state_timeout 0
> Dec 8 16:19:53 diald[48]: new state RETRY action 0x8052870
> timeout -1
> Dec 8 16:19:54 diald[48]: --- tick --- state 10 block 0
> state_timeout -1
> Dec 8 16:19:54 diald[48]: new state DOWN action 0x8051df0 timeout -1
> Dec 8 16:19:55 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:20:25 last message repeated 30 times
> Dec 8 16:20:26 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:20:26 diald[48]: filter accepted rule 22 proto 134645008
> len 58 packet 192.168.0.1,1024 =>
> <DNS address>,53
> Dec 8 16:20:26 diald[48]: Trigger: udp 192.168.0.1/1024
> <DNS address>/53
> Dec 8 16:20:26 diald[48]: new state CONNECT action 0x8051ed0
> timeout 60
> Dec 8 16:20:26 diald[48]: Calling site <remote address>
> Dec 8 16:20:27 diald[48]: running '/usr/sbin/chat -f
> /etc/ppp/peers/chat-myISP'
> Dec 8 16:20:27 diald[48]: --- tick --- state 1 block 0
> state_timeout 59
>
> <down to>
>
> Dec 8 16:20:31 diald[48]: --- tick --- state 1 block 0
> state_timeout 55
> Dec 8 16:20:31 diald[48]: filter accepted rule 22 proto 134645008
> len 58 packet 192.168.0.1,1024 =>
> <DNS address>,53
> Dec 8 16:20:32 diald[48]: --- tick --- state 1 block 0
> state_timeout 54
>
> <down to>
>
> Dec 8 16:20:56 diald[48]: --- tick --- state 1 block 0
> state_timeout 30
> Dec 8 16:20:56 diald[48]: filter accepted rule 22 proto 134645008
> len 58 packet 192.168.0.1,1024 =>
> <DNS address>,53
> Dec 8 16:20:57 diald[48]: SIGCHLD[19]: pid 262 dial, status 0
> Dec 8 16:20:57 diald[48]: new state START_LINK action 0x8052200
> timeout 60
> Dec 8 16:20:57 diald[48]: Connected to site <remote address>
> Dec 8 16:20:57 diald[48]: Running pppd (pid = 263).
> Dec 8 16:20:57 diald[263]: Running pppd: /usr/sbin/pppd
> -defaultroute
> -detach modem crtscts mtu 1500 mru 1500
> netmask 255.255.255.255 name <host name>
> Dec 8 16:20:57 pppd[263]: pppd 2.3.9 started by root, uid 0
> Dec 8 16:20:57 pppd[263]: Using interface ppp0
> Dec 8 16:20:57 pppd[263]: Connect: ppp0 <--> /dev/ttyS0
> Dec 8 16:20:57 diald[48]: --- tick --- state 4 block 0
> state_timeout 59
>
> <down to>
>
> Dec 8 16:21:01 diald[48]: --- tick --- state 4 block 0
> state_timeout 55
> Dec 8 16:21:01 pppd[263]: local IP address <local address>
> Dec 8 16:21:01 pppd[263]: remote IP address <remote address>
> Dec 8 16:21:02 diald[48]: --- tick --- state 4 block 0
> state_timeout 54
> Dec 8 16:21:02 diald[48]: New addresses: local <local address>,
> remote <remote address>, broadcast 0.0.0.0
> Dec 8 16:21:02 diald[48]: running '/sbin/ifconfig ppp0
> <local address>
> pointopoint <remote address>
> broadcast 0.0.0.0
> netmask 255.255.255.255 metric 0
> mtu 1500 up'
> Dec 8 16:21:02 diald[48]: start ppp0: SIOCSIFMETRIC: Operation not
> supported
> Dec 8 16:21:02 diald[48]: SIGCHLD[20]: pid 269 system, status 256
> Dec 8 16:21:02 diald[48]: start ppp0: Establishing routes for ppp0
> Dec 8 16:21:02 diald[48]: running '/sbin/route add <remote address>
> metric 0 dev ppp0'
> Dec 8 16:21:02 diald[48]: SIGCHLD[21]: pid 270 system, status 0
> Dec 8 16:21:02 diald[48]: running '/sbin/route add default metric 0
> netmask 0.0.0.0 dev ppp0'
> Dec 8 16:21:02 diald[48]: SIGCHLD[22]: pid 271 system, status 0
> Dec 8 16:21:02 diald[48]: stop tap0: Removing routes for tap0
> Dec 8 16:21:02 diald[48]: running '/sbin/route del default metric 0
> netmask 0.0.0.0 dev tap0'
> Dec 8 16:21:02 diald[48]: SIGCHLD[23]: pid 272 system, status 0
> Dec 8 16:21:02 diald[48]: running '/sbin/ifconfig tap0 down'
> Dec 8 16:21:02 diald[48]: SIGCHLD[24]: pid 273 system, status 0
> Dec 8 16:21:02 diald[48]: new state UP action 0x8052390 timeout 120
> Dec 8 16:21:02 diald[48]: Changed snoop device to ppp0
> Dec 8 16:21:03 diald[48]: --- tick --- state 7 block 0
> state_timeout 119
> Dec 8 16:21:04 diald[48]: --- tick --- state 7 block 0
> state_timeout 118
> Dec 8 16:21:05 diald[48]: --- tick --- state 7 block 0
> state_timeout 117
> Dec 8 16:21:06 diald[48]: --- tick --- state 7 block 0
> state_timeout 116
> Dec 8 16:21:06 diald[48]: filter accepted rule 22 proto 134645008
> len 58 packet <local address>,1024 =>
> <DNS address>,53
>
> <and so on, down to>
>
> Dec 8 16:22:15 diald[48]: filter accepted rule 7 proto tcp len 52
> seq 74dcaa41 ack 86dd69f7 flags ACK
> packet 209.144.167.151,80 =>
> <local address>,1026
> Dec 8 16:22:16 diald[48]: --- tick --- state 7 block 0
> state_timeout -1
> Dec 8 16:22:47 last message repeated 31 times
> Dec 8 16:23:48 last message repeated 61 times
> Dec 8 16:24:15 last message repeated 27 times
> Dec 8 16:24:15 diald[48]: Closing down idle link.
> Dec 8 16:24:15 diald[48]: running '/sbin/ifconfig tap0 192.168.0.1
> pointopoint 192.168.0.2 broadcast 0.0.0.0
> netmask 255.255.255.255 metric 0
> mtu 1500 up'
> Dec 8 16:24:15 diald[48]: start tap0: SIOCSIFMETRIC: Operation not
> supported
> Dec 8 16:24:15 diald[48]: SIGCHLD[25]: pid 276 system, status 256
> Dec 8 16:24:15 diald[48]: start tap0: Establishing routes for tap0
> Dec 8 16:24:15 diald[48]: running '/sbin/route add 192.168.0.2
> metric 0 dev tap0'
> Dec 8 16:24:15 diald[48]: SIGCHLD[26]: pid 277 system, status 0
> Dec 8 16:24:15 diald[48]: running '/sbin/route add default metric 0
> netmask 0.0.0.0 dev tap0'
> Dec 8 16:24:15 diald[48]: SIGCHLD[27]: pid 278 system, status 0
> Dec 8 16:24:15 diald[48]: stop ppp0: Removing routes for ppp0
> Dec 8 16:24:15 diald[48]: running '/sbin/route del default metric 0
> netmask 0.0.0.0 dev ppp0'
> Dec 8 16:24:15 diald[48]: SIGCHLD[28]: pid 279 system, status 0
> Dec 8 16:24:15 diald[48]: running '/sbin/ifconfig ppp0 down'
> Dec 8 16:24:15 diald[48]: SIGCHLD[29]: pid 280 system, status 0
> Dec 8 16:24:15 diald[48]: Closed fwdfd
> Dec 8 16:24:15 diald[48]: Changed snoop device to tap0
> Dec 8 16:24:15 diald[48]: new state STOP_LINK action 0x8052330
> timeout 60
> Dec 8 16:24:15 pppd[263]: Terminating on signal 2.
> Dec 8 16:24:15 pppd[263]: Connection terminated.
> Dec 8 16:24:15 pppd[263]: Connect time 3.3 minutes.
> Dec 8 16:24:15 pppd[263]: Sent 14475 bytes, received 12142 bytes.
> Dec 8 16:24:15 pppd[263]: Exit.
> Dec 8 16:24:15 diald[48]: SIGCHLD[30]: pid 263 link, status 1280
> Dec 8 16:24:15 diald[48]: running '/sbin/ifconfig tap0 192.168.0.1
> pointopoint 192.168.0.2 broadcast 0.0.0.0
> netmask 255.255.255.255 metric 0
> mtu 1500 up'
> Dec 8 16:24:15 diald[48]: start tap0: SIOCSIFMETRIC: Operation not
> supported
> Dec 8 16:24:15 diald[48]: SIGCHLD[31]: pid 285 system, status 256
> Dec 8 16:24:15 diald[48]: start tap0: Establishing routes for tap0
> Dec 8 16:24:15 diald[48]: running '/sbin/route add 192.168.0.2
> metric 0 dev tap0'
> Dec 8 16:24:16 diald[48]: start tap0: SIOCADDRT: File exists
> Dec 8 16:24:16 diald[48]: SIGCHLD[32]: pid 286 system, status 1792
> Dec 8 16:24:16 diald[48]: running '/sbin/route add default metric 0
> netmask 0.0.0.0 dev tap0'
> Dec 8 16:24:16 diald[48]: start tap0: SIOCADDRT: File exists
> Dec 8 16:24:16 diald[48]: SIGCHLD[33]: pid 287 system, status 1792
> Dec 8 16:24:16 diald[48]: new state DISCONNECT action 0x8052660
> timeout 60
> Dec 8 16:24:16 diald[48]: new state CLOSE action 0x80526f0
> timeout -1
> Dec 8 16:24:16 diald[48]: Closing /dev/ttyS0
> Dec 8 16:24:17 diald[48]: Delaying 30 seconds before clear to dial.
> Dec 8 16:24:17 diald[48]: --- tick --- state 9 block 0
> state_timeout 29
>
> <and so on, down to>
>
> Dec 8 16:24:46 diald[48]: --- tick --- state 9 block 0
> state_timeout 0
> Dec 8 16:24:46 diald[48]: new state RETRY action 0x8052870
> timeout -1
> Dec 8 16:24:47 diald[48]: --- tick --- state 10 block 0
> state_timeout -1
> Dec 8 16:24:47 diald[48]: new state DOWN action 0x8051df0 timeout -1
> Dec 8 16:24:48 diald[48]: --- tick --- state 0 block 0
> state_timeout -1
> Dec 8 16:25:19 last message repeated 31 times
> Dec 8 16:26:20 last message repeated 61 times
>
> 2. /etc/diald.conf file
> -----------------------
>
> mode ppp
> connect "/usr/sbin/chat -f /etc/ppp/peers/chat-myISP"
> device /dev/ttyS0
> speed 115200
> modem
> lock
> crtscts
> dynamic
> local 192.168.0.1 <----- dummy
> remote 192.168.0.2 <----- dummy
> netmask 255.255.255.255
> pppd-options name <host name>
> defaultroute
> include /usr/lib/diald/standard.filter
> debug 63
>
> /etc/ppp/options file
> ---------------------
> noauth
>
> /etc/peers/chat-myISP file
> --------------------------
> ABORT "BUSY"
> ABORT "NO ANSWER"
> ABORT "NO CARRIER"
> ABORT "RINGING\r\n\r\nRINGING"
> ABORT "NONE"
> "" "AT&F&C1&D2L3"
> OK-+++\c-OK "ATH0"
> TIMEOUT 90
> OK "ATDT<telephone number>"
> CONNECT ""
> "ogin:-ogin:" "<hostname>"
> TIMEOUT 60
> "assword:-assword:" "<password>"
> TIMEOUT 60
> "otocol:-ool:" "PPP,idle=0"
> TIMEOUT 60
> HELLO ""
>
> Many thanks in advance,
>
>
> Robin Cosby
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe
> linux-diald" in
> the body of a message to [EMAIL PROTECTED]
>
-
To unsubscribe from this list: send the line "unsubscribe linux-diald" in
the body of a message to [EMAIL PROTECTED]
