From: André Apitzsch <[email protected]> Add support for SY7802 flash LED controller. It can support up to 1.8A flash current.
Signed-off-by: André Apitzsch <[email protected]> --- drivers/leds/flash/Kconfig | 11 + drivers/leds/flash/Makefile | 1 + drivers/leds/flash/leds-sy7802.c | 532 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 544 insertions(+) diff --git a/drivers/leds/flash/Kconfig b/drivers/leds/flash/Kconfig index 809b6d98bb3e..f39f0bfe6eef 100644 --- a/drivers/leds/flash/Kconfig +++ b/drivers/leds/flash/Kconfig @@ -121,4 +121,15 @@ config LEDS_SGM3140 This option enables support for the SGM3140 500mA Buck/Boost Charge Pump LED Driver. +config LEDS_SY7802 + tristate "LED support for the Silergy SY7802" + depends on I2C && OF + depends on GPIOLIB + select REGMAP_I2C + help + This option enables support for the SY7802 flash LED controller. + SY7802 includes torch and flash functions with programmable current. + + This driver can be built as a module, it will be called "leds-sy7802". + endif # LEDS_CLASS_FLASH diff --git a/drivers/leds/flash/Makefile b/drivers/leds/flash/Makefile index 91d60a4b7952..48860eeced79 100644 --- a/drivers/leds/flash/Makefile +++ b/drivers/leds/flash/Makefile @@ -11,3 +11,4 @@ obj-$(CONFIG_LEDS_QCOM_FLASH) += leds-qcom-flash.o obj-$(CONFIG_LEDS_RT4505) += leds-rt4505.o obj-$(CONFIG_LEDS_RT8515) += leds-rt8515.o obj-$(CONFIG_LEDS_SGM3140) += leds-sgm3140.o +obj-$(CONFIG_LEDS_SY7802) += leds-sy7802.o diff --git a/drivers/leds/flash/leds-sy7802.c b/drivers/leds/flash/leds-sy7802.c new file mode 100644 index 000000000000..c03a571b0e08 --- /dev/null +++ b/drivers/leds/flash/leds-sy7802.c @@ -0,0 +1,532 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Silergy SY7802 flash LED driver with I2C interface + * + * Copyright 2024 André Apitzsch <[email protected]> + */ + +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/led-class-flash.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> + +#define SY7802_MAX_LEDS 2 +#define SY7802_LED_JOINT 2 + +#define SY7802_REG_ENABLE 0x10 +#define SY7802_REG_TORCH_BRIGHTNESS 0xa0 +#define SY7802_REG_FLASH_BRIGHTNESS 0xb0 +#define SY7802_REG_FLASH_DURATION 0xc0 +#define SY7802_REG_FLAGS 0xd0 +#define SY7802_REG_CONFIG_1 0xe0 +#define SY7802_REG_CONFIG_2 0xf0 +#define SY7802_REG_VIN_MONITOR 0x80 +#define SY7802_REG_LAST_FLASH 0x81 +#define SY7802_REG_VLED_MONITOR 0x30 +#define SY7802_REG_ADC_DELAY 0x31 +#define SY7802_REG_DEV_ID 0xff + +#define SY7802_MODE_OFF 0 +#define SY7802_MODE_TORCH 2 +#define SY7802_MODE_FLASH 3 +#define SY7802_MODE_MASK GENMASK(1, 0) + +#define SY7802_LEDS_SHIFT 3 +#define SY7802_LEDS_MASK(_id) (BIT(_id) << SY7802_LEDS_SHIFT) +#define SY7802_LEDS_MASK_ALL (SY7802_LEDS_MASK(0) | SY7802_LEDS_MASK(1)) + +#define SY7802_TORCH_CURRENT_SHIFT 3 +#define SY7802_TORCH_CURRENT_MASK(_id) \ + (GENMASK(2, 0) << (SY7802_TORCH_CURRENT_SHIFT * (_id))) +#define SY7802_TORCH_CURRENT_MASK_ALL \ + (SY7802_TORCH_CURRENT_MASK(0) | SY7802_TORCH_CURRENT_MASK(1)) + +#define SY7802_FLASH_CURRENT_SHIFT 4 +#define SY7802_FLASH_CURRENT_MASK(_id) \ + (GENMASK(3, 0) << (SY7802_FLASH_CURRENT_SHIFT * (_id))) +#define SY7802_FLASH_CURRENT_MASK_ALL \ + (SY7802_FLASH_CURRENT_MASK(0) | SY7802_FLASH_CURRENT_MASK(1)) + +#define SY7802_TIMEOUT_DEFAULT_US 512000U +#define SY7802_TIMEOUT_MIN_US 32000U +#define SY7802_TIMEOUT_MAX_US 1024000U +#define SY7802_TIMEOUT_STEPSIZE_US 32000U + +#define SY7802_TORCH_BRIGHTNESS_MAX 8 + +#define SY7802_FLASH_BRIGHTNESS_DEFAULT 14 +#define SY7802_FLASH_BRIGHTNESS_MIN 0 +#define SY7802_FLASH_BRIGHTNESS_MAX 15 +#define SY7802_FLASH_BRIGHTNESS_STEP 1 + +#define SY7802_FLAG_TIMEOUT (1 << 0) +#define SY7802_FLAG_THERMAL_SHUTDOWN (1 << 1) +#define SY7802_FLAG_LED_FAULT (1 << 2) +#define SY7802_FLAG_TX1_INTERRUPT (1 << 3) +#define SY7802_FLAG_TX2_INTERRUPT (1 << 4) +#define SY7802_FLAG_LED_THERMAL_FAULT (1 << 5) +#define SY7802_FLAG_FLASH_INPUT_VOLTAGE_LOW (1 << 6) +#define SY7802_FLAG_INPUT_VOLTAGE_LOW (1 << 7) + +#define SY7802_CHIP_ID 0x51 + +static const struct reg_default sy7802_regmap_defs[] = { + { SY7802_REG_ENABLE, SY7802_LEDS_MASK_ALL }, + { SY7802_REG_TORCH_BRIGHTNESS, 0x92 }, + { SY7802_REG_FLASH_BRIGHTNESS, SY7802_FLASH_BRIGHTNESS_DEFAULT | + SY7802_FLASH_BRIGHTNESS_DEFAULT << SY7802_FLASH_CURRENT_SHIFT }, + { SY7802_REG_FLASH_DURATION, 0x6f }, + { SY7802_REG_FLAGS, 0x0 }, + { SY7802_REG_CONFIG_1, 0x68 }, + { SY7802_REG_CONFIG_2, 0xf0 }, +}; + +struct sy7802_led { + struct led_classdev_flash flash; + struct sy7802 *chip; + u8 led_no; +}; + +struct sy7802 { + struct mutex mutex; + struct device *dev; + struct regmap *regmap; + + struct gpio_desc *enable_gpio; + struct regulator *vin_regulator; + + unsigned int fled_strobe_used; + unsigned int fled_torch_used; + unsigned int leds_active; + int num_leds; + struct sy7802_led leds[] __counted_by(num_leds); +}; + +static int sy7802_torch_brightness_set(struct led_classdev *lcdev, enum led_brightness level) +{ + struct sy7802_led *led = container_of(lcdev, struct sy7802_led, flash.led_cdev); + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ? SY7802_LEDS_MASK_ALL : + SY7802_LEDS_MASK(led->led_no); + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask; + u32 val = level ? led_enable_mask : SY7802_MODE_OFF; + struct sy7802 *chip = led->chip; + u32 curr; + u32 mask; + int ret; + + mutex_lock(&chip->mutex); + + /* + * There is only one set of flash control logic, and this flag is used to check if 'strobe' + * is currently being used. + */ + if (chip->fled_strobe_used) { + dev_warn(chip->dev, "Please disable strobe first [%d]\n", chip->fled_strobe_used); + ret = -EBUSY; + goto unlock; + } + + if (level) + curr = chip->fled_torch_used | BIT(led->led_no); + else + curr = chip->fled_torch_used & ~BIT(led->led_no); + + if (curr) + val |= SY7802_MODE_TORCH; + + /* Torch needs to be disabled first to apply new brightness */ + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, SY7802_MODE_MASK, + SY7802_MODE_OFF); + if (ret) + goto unlock; + + mask = led->led_no == SY7802_LED_JOINT ? SY7802_TORCH_CURRENT_MASK_ALL : + SY7802_TORCH_CURRENT_MASK(led->led_no); + + /* Register expects brightness between 0 and MAX_BRIGHTNESS - 1 */ + if (level) + level -= 1; + + level |= (level << SY7802_TORCH_CURRENT_SHIFT); + + ret = regmap_update_bits(chip->regmap, SY7802_REG_TORCH_BRIGHTNESS, mask, level); + if (ret) + goto unlock; + + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, enable_mask, val); + if (ret) + goto unlock; + + chip->fled_torch_used = curr; + +unlock: + mutex_unlock(&chip->mutex); + return ret; +} + +static int sy7802_flash_brightness_set(struct led_classdev_flash *fl_cdev, u32 brightness) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + struct led_flash_setting *s = &fl_cdev->brightness; + u32 val = (brightness - s->min) / s->step; + struct sy7802 *chip = led->chip; + u32 mask; + int ret; + + val |= (val << SY7802_FLASH_CURRENT_SHIFT); + mask = led->led_no == SY7802_LED_JOINT ? SY7802_FLASH_CURRENT_MASK_ALL : + SY7802_FLASH_CURRENT_MASK(led->led_no); + + mutex_lock(&chip->mutex); + ret = regmap_update_bits(chip->regmap, SY7802_REG_FLASH_BRIGHTNESS, mask, val); + mutex_unlock(&chip->mutex); + + return ret; +} + +static int sy7802_strobe_set(struct led_classdev_flash *fl_cdev, bool state) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ? SY7802_LEDS_MASK_ALL : + SY7802_LEDS_MASK(led->led_no); + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask; + u32 val = state ? led_enable_mask : SY7802_MODE_OFF; + struct sy7802 *chip = led->chip; + u32 curr; + int ret; + + mutex_lock(&chip->mutex); + + /* + * There is only one set of flash control logic, and this flag is used to check if 'torch' + * is currently being used. + */ + if (chip->fled_torch_used) { + dev_warn(chip->dev, "Please disable torch first [0x%x]\n", chip->fled_torch_used); + ret = -EBUSY; + goto unlock; + } + + if (state) + curr = chip->fled_strobe_used | BIT(led->led_no); + else + curr = chip->fled_strobe_used & ~BIT(led->led_no); + + if (curr) + val |= SY7802_MODE_FLASH; + + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, enable_mask, val); + + if (ret) + goto unlock; + + chip->fled_strobe_used = curr; + +unlock: + mutex_unlock(&chip->mutex); + return ret; +} + +static int sy7802_strobe_get(struct led_classdev_flash *fl_cdev, bool *state) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + struct sy7802 *chip = led->chip; + + mutex_lock(&chip->mutex); + *state = !!(chip->fled_strobe_used & BIT(led->led_no)); + mutex_unlock(&chip->mutex); + + return 0; +} + +static int sy7802_timeout_set(struct led_classdev_flash *fl_cdev, + u32 timeout) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + struct led_flash_setting *s = &fl_cdev->timeout; + u32 val = (timeout - s->min) / s->step; + struct sy7802 *chip = led->chip; + + return regmap_write(chip->regmap, SY7802_REG_FLASH_DURATION, val); +} + +static int sy7802_fault_get(struct led_classdev_flash *fl_cdev, u32 *fault) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + struct sy7802 *chip = led->chip; + u32 val, led_faults = 0; + int ret; + + /* NOTE: reading register clears fault status */ + ret = regmap_read(chip->regmap, SY7802_REG_FLAGS, &val); + if (ret) + return ret; + + if (val & (SY7802_FLAG_FLASH_INPUT_VOLTAGE_LOW | SY7802_FLAG_INPUT_VOLTAGE_LOW)) + led_faults |= LED_FAULT_INPUT_VOLTAGE; + + if (val & SY7802_FLAG_THERMAL_SHUTDOWN) + led_faults |= LED_FAULT_OVER_TEMPERATURE; + + if (val & SY7802_FLAG_TIMEOUT) + led_faults |= LED_FAULT_TIMEOUT; + + *fault = led_faults; + return 0; +} + +static const struct led_flash_ops sy7802_flash_ops = { + .flash_brightness_set = sy7802_flash_brightness_set, + .strobe_set = sy7802_strobe_set, + .strobe_get = sy7802_strobe_get, + .timeout_set = sy7802_timeout_set, + .fault_get = sy7802_fault_get, +}; + +static void sy7802_init_flash_brightness(struct led_classdev_flash *fl_cdev) +{ + struct led_flash_setting *s; + + /* Init flash brightness setting */ + s = &fl_cdev->brightness; + s->min = SY7802_FLASH_BRIGHTNESS_MIN; + s->max = SY7802_FLASH_BRIGHTNESS_MAX; + s->step = SY7802_FLASH_BRIGHTNESS_STEP; + s->val = SY7802_FLASH_BRIGHTNESS_DEFAULT; +} + +static void sy7802_init_flash_timeout(struct led_classdev_flash *fl_cdev) +{ + struct led_flash_setting *s; + + /* Init flash timeout setting */ + s = &fl_cdev->timeout; + s->min = SY7802_TIMEOUT_MIN_US; + s->max = SY7802_TIMEOUT_MAX_US; + s->step = SY7802_TIMEOUT_STEPSIZE_US; + s->val = SY7802_TIMEOUT_DEFAULT_US; +} + +static int sy7802_led_register(struct device *dev, struct sy7802_led *led, + struct device_node *np) +{ + struct led_init_data init_data = {}; + int ret; + + init_data.fwnode = of_fwnode_handle(np); + + ret = devm_led_classdev_flash_register_ext(dev, &led->flash, &init_data); + if (ret) { + dev_err(dev, "Couldn't register flash %d\n", led->led_no); + return ret; + } + + return ret; +} + +static int sy7802_init_flash_properties(struct device *dev, struct sy7802_led *led, + struct device_node *np) +{ + struct led_classdev_flash *flash = &led->flash; + struct led_classdev *lcdev = &flash->led_cdev; + u32 sources[SY7802_MAX_LEDS]; + int i, num, ret; + + num = of_property_count_u32_elems(np, "led-sources"); + if (num < 1) { + dev_err(dev, "Not specified or wrong number of led-sources\n"); + return -EINVAL; + } + + ret = of_property_read_u32_array(np, "led-sources", sources, num); + if (ret) + return ret; + + for (i = 0; i < num; i++) { + if (sources[i] >= SY7802_MAX_LEDS) + return -EINVAL; + if (led->chip->leds_active & BIT(sources[i])) + return -EINVAL; + led->chip->leds_active |= BIT(sources[i]); + } + + /* If both channels are specified in 'led-sources', joint flash output mode is used */ + led->led_no = num == 2 ? SY7802_LED_JOINT : sources[0]; + + lcdev->max_brightness = SY7802_TORCH_BRIGHTNESS_MAX; + lcdev->brightness_set_blocking = sy7802_torch_brightness_set; + lcdev->flags |= LED_DEV_CAP_FLASH; + + flash->ops = &sy7802_flash_ops; + + sy7802_init_flash_brightness(flash); + sy7802_init_flash_timeout(flash); + + return 0; +} + +static int sy7802_chip_check(struct sy7802 *chip) +{ + struct device *dev = chip->dev; + u32 chipid; + int ret; + + ret = regmap_read(chip->regmap, SY7802_REG_DEV_ID, &chipid); + if (ret) + return dev_err_probe(dev, ret, "Failed to read chip ID\n"); + + if (chipid != SY7802_CHIP_ID) + return dev_err_probe(dev, -ENODEV, "Chip reported wrong ID: %x\n", chipid); + + return 0; +} + +static void sy7802_enable(struct sy7802 *chip) +{ + gpiod_set_value_cansleep(chip->enable_gpio, 1); + usleep_range(200, 300); +} + +static void sy7802_disable(struct sy7802 *chip) +{ + gpiod_set_value_cansleep(chip->enable_gpio, 0); +} + +static int sy7802_probe_dt(struct sy7802 *chip) +{ + struct device_node *np = dev_of_node(chip->dev), *child; + int i = 0; + int ret; + + regmap_write(chip->regmap, SY7802_REG_ENABLE, SY7802_MODE_OFF); + regmap_write(chip->regmap, SY7802_REG_TORCH_BRIGHTNESS, LED_OFF); + + for_each_available_child_of_node(np, child) { + struct sy7802_led *led = chip->leds + i; + + led->chip = chip; + led->led_no = i; + + ret = sy7802_init_flash_properties(chip->dev, led, child); + if (ret) { + of_node_put(child); + return ret; + } + + ret = sy7802_led_register(chip->dev, led, child); + if (ret) { + of_node_put(child); + return ret; + } + + i++; + } + return 0; +} + +static const struct regmap_config sy7802_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = 0xff, + .cache_type = REGCACHE_MAPLE, + .reg_defaults = sy7802_regmap_defs, + .num_reg_defaults = ARRAY_SIZE(sy7802_regmap_defs), +}; + +static int sy7802_probe(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct sy7802 *chip; + size_t count; + int ret; + + count = device_get_child_node_count(dev); + if (!count || count > SY7802_MAX_LEDS) + return dev_err_probe(dev, -EINVAL, + "No child node or node count over max led number %zu\n", count); + + chip = devm_kzalloc(dev, struct_size(chip, leds, count), GFP_KERNEL); + if (!chip) + return -ENOMEM; + + chip->num_leds = count; + + chip->dev = dev; + i2c_set_clientdata(client, chip); + + chip->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW); + ret = PTR_ERR_OR_ZERO(chip->enable_gpio); + if (ret) + return dev_err_probe(dev, ret, "Failed to request enable gpio\n"); + + chip->vin_regulator = devm_regulator_get(dev, "vin"); + ret = PTR_ERR_OR_ZERO(chip->vin_regulator); + if (ret) + return dev_err_probe(dev, ret, "Failed to request regulator\n"); + + ret = regulator_enable(chip->vin_regulator); + if (ret) + return dev_err_probe(dev, ret, "Failed to enable regulator\n"); + + chip->regmap = devm_regmap_init_i2c(client, &sy7802_regmap_config); + if (IS_ERR(chip->regmap)) { + regulator_disable(chip->vin_regulator); + return dev_err_probe(dev, PTR_ERR(chip->regmap), + "Failed to allocate register map.\n"); + } + + ret = sy7802_probe_dt(chip); + if (ret < 0) { + regulator_disable(chip->vin_regulator); + return ret; + } + + sy7802_enable(chip); + + ret = sy7802_chip_check(chip); + if (ret) { + sy7802_disable(chip); + regulator_disable(chip->vin_regulator); + return ret; + } + + mutex_init(&chip->mutex); + + return ret; +} + +static void sy7802_remove(struct i2c_client *client) +{ + struct sy7802 *chip = i2c_get_clientdata(client); + + sy7802_disable(chip); + + mutex_destroy(&chip->mutex); + regulator_disable(chip->vin_regulator); +} + +static const struct of_device_id __maybe_unused sy7802_leds_match[] = { + { .compatible = "silergy,sy7802", }, + {} +}; + +MODULE_DEVICE_TABLE(of, sy7802_leds_match); + +static struct i2c_driver sy7802_driver = { + .driver = { + .name = "sy7802", + .of_match_table = of_match_ptr(sy7802_leds_match), + }, + .probe = sy7802_probe, + .remove = sy7802_remove, +}; + +module_i2c_driver(sy7802_driver); + +MODULE_AUTHOR("André Apitzsch <[email protected]>"); +MODULE_DESCRIPTION("Silergy SY7802 flash LED driver"); +MODULE_LICENSE("GPL"); -- 2.44.0
