Hi, This version has improved patch description (on the second thought the original patch description was too vague).
Bart [PATCH] pata_pdc202xx_old: fix possible data corruption and other problems Fix wrong "port" calculations in pdc202xx_{configure_piomode,set_dmamode}() They were broken for all configurations except one (master device on primary channel, no other devices) and as a result device settings + PIO/DMA timings were being programmed into the wrong PCI registers. This could result in a large variety of problems including data corruption, hangs etc. (depending on devices used and your luck :-). ap->port_no ap->devno used PCI registers correct PCI registers 0 0 0x60-0x62 0x60-0x62 0 1 0x62-0x64 0x64-0x66 1 0 0x64-0x66 0x68-0x6a 1 1 0x66-0x68 0x6c-0x6e Also forward port recent fixes from drivers/ide pdc202xx_old driver: * fix XFER_MW_DMA0 timings (they were overclocked, use the official ones) * fix bitmasks for clearing bits of register B: - when programming DMA mode bit 0x10 of register B was cleared which resulted in overclocked PIO timing setting (iff PIO0 was used) - when programming PIO mode bits 0x18 weren't cleared so suboptimal timings were used for PIO1-4 if PIO0 was previously set (bit 0x10) and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08) and finally bump driver version. Signed-off-by: Bartlomiej Zolnierkiewicz <[EMAIL PROTECTED]> --- drivers/ata/pata_pdc202xx_old.c | 22 ++++++++++++++-------- 1 file changed, 14 insertions(+), 8 deletions(-) Index: b/drivers/ata/pata_pdc202xx_old.c =================================================================== --- a/drivers/ata/pata_pdc202xx_old.c +++ b/drivers/ata/pata_pdc202xx_old.c @@ -2,13 +2,14 @@ * pata_pdc202xx_old.c - Promise PDC202xx PATA for new ATA layer * (C) 2005 Red Hat Inc * Alan Cox <[EMAIL PROTECTED]> + * (C) 2007 Bartlomiej Zolnierkiewicz * * Based in part on linux/drivers/ide/pci/pdc202xx_old.c * * First cut with LBA48/ATAPI * * TODO: - * Channel interlock/reset on both required ? + * Channel interlock/reset on both required */ #include <linux/kernel.h> @@ -21,7 +22,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_pdc202xx_old" -#define DRV_VERSION "0.3.0" +#define DRV_VERSION "0.4.0" /** * pdc2024x_pre_reset - probe begin @@ -76,7 +77,7 @@ static void pdc2026x_error_handler(struc static void pdc202xx_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); - int port = 0x60 + 4 * ap->port_no + 2 * adev->devno; + int port = 0x60 + 8 * ap->port_no + 4 * adev->devno; static u16 pio_timing[5] = { 0x0913, 0x050C , 0x0308, 0x0206, 0x0104 }; @@ -85,7 +86,7 @@ static void pdc202xx_configure_piomode(s pci_read_config_byte(pdev, port, &r_ap); pci_read_config_byte(pdev, port + 1, &r_bp); r_ap &= ~0x3F; /* Preserve ERRDY_EN, SYNC_IN */ - r_bp &= ~0x07; + r_bp &= ~0x1F; r_ap |= (pio_timing[pio] >> 8); r_bp |= (pio_timing[pio] & 0xFF); @@ -123,7 +124,7 @@ static void pdc202xx_set_piomode(struct static void pdc202xx_set_dmamode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); - int port = 0x60 + 4 * ap->port_no + 2 * adev->devno; + int port = 0x60 + 8 * ap->port_no + 4 * adev->devno; static u8 udma_timing[6][2] = { { 0x60, 0x03 }, /* 33 Mhz Clock */ { 0x40, 0x02 }, @@ -132,12 +133,17 @@ static void pdc202xx_set_dmamode(struct { 0x20, 0x01 }, { 0x20, 0x01 } }; + static u8 mdma_timing[3][2] = { + { 0x60, 0x03 }, + { 0x60, 0x04 }, + { 0xe0, 0x0f }, + }; u8 r_bp, r_cp; pci_read_config_byte(pdev, port + 1, &r_bp); pci_read_config_byte(pdev, port + 2, &r_cp); - r_bp &= ~0xF0; + r_bp &= ~0xE0; r_cp &= ~0x0F; if (adev->dma_mode >= XFER_UDMA_0) { @@ -147,8 +153,8 @@ static void pdc202xx_set_dmamode(struct } else { int speed = adev->dma_mode - XFER_MW_DMA_0; - r_bp |= 0x60; - r_cp |= (5 - speed); + r_bp |= mdma_timing[speed][0]; + r_cp |= mdma_timing[speed][1]; } pci_write_config_byte(pdev, port + 1, r_bp); pci_write_config_byte(pdev, port + 2, r_cp); - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html