I just wanted to have a look at the patch and see if it works for me -
looks like somethings not all straight, I get this while booting:
ahci 0000:00:1f.2: version 2.2
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: nr_ports (3) and implemented port map (0x1) don't match
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x1 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
ata1: SATA max UDMA/133 cmd 0xffffc20000048100 ctl 0x0000000000000000
bmdma 0x0000000000000000 irq 0
WARNING: at drivers/ata/libata-eh.c:1917 ata_eh_set_powersave()
Call Trace:
[<ffffffff804a99ce>] ata_eh_set_powersave+0x34e/0x370
[<ffffffff8048c7b0>] scsi_error_handler+0x0/0x330
[<ffffffff804a9e27>] ata_do_eh+0xb7/0x16f0
[<ffffffff80229f9d>] find_busiest_group+0x1bd/0x800
[<ffffffff804aece0>] ahci_postreset+0x0/0x80
[<ffffffff804ada70>] ahci_hardreset+0x0/0xf0
[<ffffffff804aee20>] ahci_softreset+0x0/0x270
[<ffffffff804a40f0>] ata_std_prereset+0x0/0xf0
[<ffffffff8023b134>] lock_timer_base+0x34/0x70
[<ffffffff8048c7b0>] scsi_error_handler+0x0/0x330
[<ffffffff8048c7b0>] scsi_error_handler+0x0/0x330
[<ffffffff8048c7b0>] scsi_error_handler+0x0/0x330
[<ffffffff804abc27>] ata_scsi_error+0x297/0x730
[<ffffffff8048c7b0>] scsi_error_handler+0x0/0x330
[<ffffffff8048c893>] scsi_error_handler+0xe3/0x330
[<ffffffff80229507>] __wake_up_common+0x47/0x80
[<ffffffff8048c7b0>] scsi_error_handler+0x0/0x330
[<ffffffff8024675b>] kthread+0x4b/0x80
[<ffffffff8020a9a8>] child_rip+0xa/0x12
[<ffffffff80246710>] kthread+0x0/0x80
[<ffffffff8020a99e>] child_rip+0x0/0x12
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ata_hpa_resize 1: sectors = 312581808, hpa_sectors = 312581808
ata1.00: ATA-7: Hitachi HTS541616J9SA00, SB4OC7DP, max UDMA/100
ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: ata_hpa_resize 1: sectors = 312581808, hpa_sectors = 312581808
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54161 SB4O PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
I hope this output from dmesg helps to make the patch better - if I can
do any further testing please let me know!
Peter
John Fremlin wrote:
Tejun Heo has made an excellent patch for saving power with the AHCI
chipset. It saves about 1 W on my Thinkpad X60s.
This patch will stop the ports when they are idle. To turn it on,
echo 1 > /sys/module/libata/parameters/powersave
This is very different from the patch I posted a while ago turning on
a few bits in the CMD register (ALPE and ASP) and which Intel is
apparently now trying. That only saves around 250mW. Tejun's patch
saves about 1 W. It should also make the ALPE and ASP stuff irrelevant
because it performs the same operation in software where better
information about usage is (theoretically) available.
I have updated the patch for 2.6.22-rc4. That is the extent of my
involvement - if it works, thank Tejun Heo. But problems are quite
likely to have been introduced by my clumsy update, so if it doesn't
work, blame me first.
------------------------------------------------------------------------
_______________________________________________
Power mailing list
[EMAIL PROTECTED]
http://www.bughost.org/mailman/listinfo/power
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html