On Mon, Dec 21, 2015 at 09:35:19PM +0800, Shawn Guo wrote:
> On Fri, Dec 18, 2015 at 12:00:32PM -0500, Damien Riegel wrote:
> > This commit adds LCD support for the TS-4800. The panel is an Okaya
> > RS800480T-7X0WQ and the timings have been extracted from Technologic
> > Systems' tree.
> >
> > Signed-off-by: Damien Riegel <damien.rie...@savoirfairelinux.com>
> > ---
> > arch/arm/boot/dts/imx51-ts4800.dts | 109
> > +++++++++++++++++++++++++++++++++++++
> > 1 file changed, 109 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/imx51-ts4800.dts
> > b/arch/arm/boot/dts/imx51-ts4800.dts
> > index 83352cb..4951ebd 100644
> > --- a/arch/arm/boot/dts/imx51-ts4800.dts
> > +++ b/arch/arm/boot/dts/imx51-ts4800.dts
> > @@ -30,6 +30,60 @@
> > clock-frequency = <24576000>;
> > };
> > };
> > +
> > + regulators {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + backlight_reg: regulator@0 {
> > + compatible = "regulator-fixed";
> > + reg = <0>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enable_lcd>;
> > + regulator-name = "enable_lcd_reg";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > + };
>
> DT maintainers dislike this fake simple-bus container. Let's put the
> regulator directly under root like below.
>
> backlight_reg: regulator-backlight {
> compatible = "regulator-fixed";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enable_lcd>;
> regulator-name = "enable_lcd_reg";
> regulator-min-microvolt = <3300000>;
> regulator-max-microvolt = <3300000>;
> gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>;
> enable-active-high;
> };
>
> I fixed it up and applied both patches.
Thank you. I am using the imx51-*.dts as examples, maybe they should be
updated to be consistent with the newer device tree style? I'm willing
to do that but I don't want to make changes on dts files that I can't
test.
Sidenote: your Signed-off-by is missing on these two patches.
Thanks,
Damien
>
> Shawn
>
> > +
> > + backlight: backlight {
> > + compatible = "pwm-backlight";
> > + pwms = <&pwm1 0 78770>;
> > + brightness-levels = <0 150 200 255>;
> > + default-brightness-level = <1>;
> > + power-supply = <&backlight_reg>;
> > + };
> > +
> > + display0: display@di0 {
> > + compatible = "fsl,imx-parallel-display";
> > + interface-pix-fmt = "rgb24";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_lcd>;
> > +
> > + display-timings {
> > + 800x480p60 {
> > + native-mode;
> > + clock-frequency = <30066000>;
> > + hactive = <800>;
> > + vactive = <480>;
> > + hfront-porch = <50>;
> > + hback-porch = <70>;
> > + hsync-len = <50>;
> > + vback-porch = <0>;
> > + vfront-porch = <0>;
> > + vsync-len = <50>;
> > + };
> > + };
> > +
> > + port@0 {
> > + display0_in: endpoint {
> > + remote-endpoint = <&ipu_di0_disp0>;
> > + };
> > + };
> > + };
> > };
> >
> > &esdhc1 {
> > @@ -60,6 +114,16 @@
> > };
> > };
> >
> > +&ipu_di0_disp0 {
> > + remote-endpoint = <&display0_in>;
> > +};
> > +
> > +&pwm1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pwm_backlight>;
> > + status = "okay";
> > +};
> > +
> > &uart1 {
> > pinctrl-names = "default";
> > pinctrl-0 = <&pinctrl_uart1>;
> > @@ -115,6 +179,12 @@
> > >;
> > };
> >
> > + pinctrl_enable_lcd: enablelcdgrp {
> > + fsl,pins = <
> > + MX51_PAD_CSI2_D12__GPIO4_9 0x1c5
> > + >;
> > + };
> > +
> > pinctrl_esdhc1: esdhc1grp {
> > fsl,pins = <
> > MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5
> > @@ -159,6 +229,45 @@
> > >;
> > };
> >
> > + pinctrl_lcd: lcdgrp {
> > + fsl,pins = <
> > + MX51_PAD_DISP1_DAT0__DISP1_DAT0 0x5
> > + MX51_PAD_DISP1_DAT1__DISP1_DAT1 0x5
> > + MX51_PAD_DISP1_DAT2__DISP1_DAT2 0x5
> > + MX51_PAD_DISP1_DAT3__DISP1_DAT3 0x5
> > + MX51_PAD_DISP1_DAT4__DISP1_DAT4 0x5
> > + MX51_PAD_DISP1_DAT5__DISP1_DAT5 0x5
> > + MX51_PAD_DISP1_DAT6__DISP1_DAT6 0x5
> > + MX51_PAD_DISP1_DAT7__DISP1_DAT7 0x5
> > + MX51_PAD_DISP1_DAT8__DISP1_DAT8 0x5
> > + MX51_PAD_DISP1_DAT9__DISP1_DAT9 0x5
> > + MX51_PAD_DISP1_DAT10__DISP1_DAT10 0x5
> > + MX51_PAD_DISP1_DAT11__DISP1_DAT11 0x5
> > + MX51_PAD_DISP1_DAT12__DISP1_DAT12 0x5
> > + MX51_PAD_DISP1_DAT13__DISP1_DAT13 0x5
> > + MX51_PAD_DISP1_DAT14__DISP1_DAT14 0x5
> > + MX51_PAD_DISP1_DAT15__DISP1_DAT15 0x5
> > + MX51_PAD_DISP1_DAT16__DISP1_DAT16 0x5
> > + MX51_PAD_DISP1_DAT17__DISP1_DAT17 0x5
> > + MX51_PAD_DISP1_DAT18__DISP1_DAT18 0x5
> > + MX51_PAD_DISP1_DAT19__DISP1_DAT19 0x5
> > + MX51_PAD_DISP1_DAT20__DISP1_DAT20 0x5
> > + MX51_PAD_DISP1_DAT21__DISP1_DAT21 0x5
> > + MX51_PAD_DISP1_DAT22__DISP1_DAT22 0x5
> > + MX51_PAD_DISP1_DAT23__DISP1_DAT23 0x5
> > + MX51_PAD_DI1_PIN2__DI1_PIN2 0x5
> > + MX51_PAD_DI1_PIN3__DI1_PIN3 0x5
> > + MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK 0x5
> > + MX51_PAD_DI_GP4__DI2_PIN15 0x5
> > + >;
> > + };
> > +
> > + pinctrl_pwm_backlight: backlightgrp {
> > + fsl,pins = <
> > + MX51_PAD_GPIO1_2__PWM1_PWMO 0x80000000
> > + >;
> > + };
> > +
> > pinctrl_uart1: uart1grp {
> > fsl,pins = <
> > MX51_PAD_UART1_RXD__UART1_RXD 0x1c5
> > --
> > 2.5.0
> >
> >
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
