On Tue, Feb 02, 2016 at 07:07:39PM +0100, Gregory CLEMENT wrote:
> From: Wilson Ding <ding...@marvell.com>
>
> Armada-3700's uart is a simple serial port, which doesn't
> support. Configuring the modem control lines. The uart port has a 32
> bytes Tx FIFO and a 64 bytes Rx FIFO
>
> The uart driver implements the uart core operations. It also support the
> system (early) console based on Armada-3700's serial port.
>
> Known Issue:
>
> The uart driver currently doesn't support clock programming, which means
> the baud-rate stays with the default value configured by the bootloader
> at boot time
To ensure that the bootloader and kernel match, it's best to place the
rate in the stdout-path property (as in
Documentation/devicetree/bindings/chosen.txt).
Presumably that is what you want?
Is it difficutl to add clock programming?
>
> [gregory.clem...@free-electrons.com: Rewrite many part which are too long
> to enumerate]
>
> Signed-off-by: Wilson Ding <ding...@marvell.com>
> Signed-off-by: Nadav Haklai <nad...@marvell.com>
> Signed-off-by: Gregory CLEMENT <gregory.clem...@free-electrons.com>
> ---
> .../devicetree/bindings/tty/serial/mvebu-uart.txt | 13 +
> Documentation/kernel-parameters.txt | 6 +
> drivers/tty/serial/Kconfig | 22 +
> drivers/tty/serial/Makefile | 1 +
> drivers/tty/serial/mvebu-uart.c | 649
> +++++++++++++++++++++
> include/uapi/linux/serial_core.h | 3 +
> 6 files changed, 694 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt
> create mode 100644 drivers/tty/serial/mvebu-uart.c
>
> diff --git a/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt
> b/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt
> new file mode 100644
> index 000000000000..6087defd9f93
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt
> @@ -0,0 +1,13 @@
> +* Marvell UART : Non standard UART used in some of Marvell EBU SoCs (e.g.,
> Armada-3700)
> +
> +Required properties:
> +- compatible: "marvell,armada-3700-uart"
> +- reg: offset and length of the register set for the device.
> +- interrupts: device interrupt
> +
> +Example:
> + serial@12000 {
> + compatible = "marvell,armada-3700-uart";
> + reg = <0x12000 0x400>;
> + interrupts = <43>;
> + };
There are no external clock inputs?
> diff --git a/Documentation/kernel-parameters.txt
> b/Documentation/kernel-parameters.txt
> index 87d40a72f6a1..198f6bd56e84 100644
> --- a/Documentation/kernel-parameters.txt
> +++ b/Documentation/kernel-parameters.txt
> @@ -1058,6 +1058,12 @@ bytes respectively. Such letter suffixes can also be
> entirely omitted.
> A valid base address must be provided, and the serial
> port must already be setup and configured.
>
> + mvebu_uart,<addr>
> + Start an early, polled-mode console on an some mvebu
> + SoC (as the Armada-3700) serial port at the specified
> + address. The serial port must already be setup and
> + configured. Options are not yet supported.
> +
Does the the mvebu UART vary between platforms at all?
Thanks,
Mark.
