On 03.06.16 22:13, Grygorii Strashko wrote:
On 06/03/2016 09:25 PM, Ivan Khoronzhuk wrote:
On 03.06.16 19:50, Grygorii Strashko wrote:
On 06/03/2016 01:43 AM, Ivan Khoronzhuk wrote:
There is no reason to hold s/w dependent parameter in device tree.
Even more, there is no reason in this parameter because davinici_cpdma
driver splits pool of descriptors equally between tx and rx channels.
That is, if number of descriptors 256, 128 of them are for rx
channels. While receiving, the descriptor is freed to the pool and
then allocated with new skb. And if in DT the "rx_descs" is set to
64, then 128 - 64 = 64 descriptors are always in the pool and cannot
be used, for tx, for instance. It's not correct resource usage,
better to set it to half of pool, then the rx pool can be used in
full. It will not have any impact on performance, as anyway, the
"redundant" descriptors were unused.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronz...@linaro.org>
---
Based on master
Documentation/devicetree/bindings/net/cpsw.txt | 3 ---
arch/arm/boot/dts/am33xx.dtsi | 1 -
arch/arm/boot/dts/am4372.dtsi | 1 -
arch/arm/boot/dts/dm814x.dtsi | 1 -
arch/arm/boot/dts/dra7.dtsi | 1 -
Pls, split DT and non-DT changes, seems code changes should go first.
Ok.
drivers/net/ethernet/ti/cpsw.c | 13 +++----------
drivers/net/ethernet/ti/cpsw.h | 1 -
drivers/net/ethernet/ti/davinci_cpdma.c | 6 ++++++
drivers/net/ethernet/ti/davinci_cpdma.h | 1 +
9 files changed, 10 insertions(+), 18 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/cpsw.txt
b/Documentation/devicetree/bindings/net/cpsw.txt
index 0ae0649..5fe6239 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -15,7 +15,6 @@ Required properties:
- cpdma_channels : Specifies number of channels in CPDMA
- ale_entries : Specifies No of entries ALE can hold
- bd_ram_size : Specifies internal descriptor RAM size
-- rx_descs : Specifies number of Rx descriptors
- mac_control : Specifies Default MAC control register content
for the specific platform
- slaves : Specifies number for slaves
@@ -70,7 +69,6 @@ Examples:
[....]
slaves = <2>;
active_slave = <0>;
diff --git a/drivers/net/ethernet/ti/cpsw.c
b/drivers/net/ethernet/ti/cpsw.c
index 4b08a2f..635be3e 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -1277,6 +1277,7 @@ static int cpsw_ndo_open(struct net_device *ndev)
ALE_ALL_PORTS, ALE_ALL_PORTS, 0, 0);
if (!cpsw_common_res_usage_state(priv)) {
+ int buf_num;
struct cpsw_priv *priv_sl0 = cpsw_get_slave_priv(priv, 0);
/* setup tx dma to fixed prio and zero offset */
@@ -1305,10 +1306,8 @@ static int cpsw_ndo_open(struct net_device *ndev)
enable_irq(priv->irqs_table[0]);
}
- if (WARN_ON(!priv->data.rx_descs))
- priv->data.rx_descs = 128;
-
- for (i = 0; i < priv->data.rx_descs; i++) {
+ buf_num = cpdma_chan_get_buf_num(priv->dma) / 2;
Could you get rid of "/ 2", pls?
Why? compiler is smart enough to translate it to shift.
And this is not time critical place.
Anyway, will change it to >> 1 while splitting.
I mean here that cpsw, in general, should not have any knowledge about rules
used by cpdma to split pool on rx and tx part. How about
cpdma_chan_get_rx_buf_num()?
Yes, it be correct.
Will change it in v2
--
Regards,
Ivan Khoronzhuk