On 20/07/16 01:02, Dmitry Torokhov wrote:
> On Mon, Jul 18, 2016 at 03:48:12PM +0300, Aleksei Mamlin wrote:
>> This patch add support for Domintech DMARD06 accelerometer.
>>
>> Domintech DMARD06 is a low-g tri-axial digital accelerometer with
>> special power saving modes suitable for consumer mobile application.
>
> I'd say this belongs to IIO. The input/misc accelerometers are mostly
> legacy.
Also note we have a dmard09 driver under review on the IIO list
at the moment. At quick glance, this looks to have a totally different
register set though so probably doesn't make sense to combine the
drivers.
Do you have docs for this part? The dmard09 driver was written
based on a vendor driver so little is known about what the other registers
are for!
Jonathan
>
>>
>> Signed-off-by: Aleksei Mamlin <mamli...@gmail.com>
>> ---
>> .../devicetree/bindings/input/dmard06.txt | 24 ++
>> drivers/input/misc/Kconfig | 12 +
>> drivers/input/misc/Makefile | 1 +
>> drivers/input/misc/dmard06.c | 442
>> +++++++++++++++++++++
>> 4 files changed, 479 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/input/dmard06.txt
>> create mode 100644 drivers/input/misc/dmard06.c
>>
>> diff --git a/Documentation/devicetree/bindings/input/dmard06.txt
>> b/Documentation/devicetree/bindings/input/dmard06.txt
>> new file mode 100644
>> index 0000000..528c318
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/input/dmard06.txt
>> @@ -0,0 +1,24 @@
>> +Device tree bindings for Domintech DMARD06 acceletometer
>> +
>> +Required properties:
>> + - compatible : Should be "domintech,dmard06"
>> + - reg : I2C address of the chip. Should be 0x1c
>> +
>> +Optional properties:
>> + - interrupt-parent : Interrupt controller to which the chip is connected
>> + - interrupts : Interrupt to which the chip is connected
>> +
>> +
>> +Example:
>> + &i2c1 {
>> + /* ... */
>> +
>> + accelerometer@1c {
>> + compatible = "domintech,dmard06";
>> + reg = <0x1c>;
>> + interrupt-parent = <&gpio>;
>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> + };
>> +
>> + /* ... */
>> + };
>> diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
>> index efb0ca8..b95e0e7 100644
>> --- a/drivers/input/misc/Kconfig
>> +++ b/drivers/input/misc/Kconfig
>> @@ -107,6 +107,18 @@ config INPUT_BMA150
>> To compile this driver as a module, choose M here: the
>> module will be called bma150.
>>
>> +config INPUT_DMARD06
>> + tristate "Domintech DMARD06 Digital Accelerometer support"
>> + depends on OF || COMPILE_TEST
>> + depends on I2C
>> + select INPUT_POLLDEV
>> + help
>> + Say Y to enable support for the Domintech DMARD06 Low-G Tri-Axial
>> + digital accelerometer connected via an I2C bus.
>> +
>> + To compile this driver as a module, choose M here: the
>> + module will be called dmard06.
>> +
>> config INPUT_E3X0_BUTTON
>> tristate "NI Ettus Research USRP E3xx Button support."
>> default n
>> diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile
>> index 6a1e5e2..d83866f 100644
>> --- a/drivers/input/misc/Makefile
>> +++ b/drivers/input/misc/Makefile
>> @@ -28,6 +28,7 @@ obj-$(CONFIG_INPUT_DA9052_ONKEY) += da9052_onkey.o
>> obj-$(CONFIG_INPUT_DA9055_ONKEY) += da9055_onkey.o
>> obj-$(CONFIG_INPUT_DA9063_ONKEY) += da9063_onkey.o
>> obj-$(CONFIG_INPUT_DM355EVM) += dm355evm_keys.o
>> +obj-$(CONFIG_INPUT_DMARD06) += dmard06.o
>> obj-$(CONFIG_INPUT_E3X0_BUTTON) += e3x0-button.o
>> obj-$(CONFIG_INPUT_DRV260X_HAPTICS) += drv260x.o
>> obj-$(CONFIG_INPUT_DRV2665_HAPTICS) += drv2665.o
>> diff --git a/drivers/input/misc/dmard06.c b/drivers/input/misc/dmard06.c
>> new file mode 100644
>> index 0000000..cc1e5a2
>> --- /dev/null
>> +++ b/drivers/input/misc/dmard06.c
>> @@ -0,0 +1,442 @@
>> +/*
>> + * Driver for Domintech DMARD06 accelerometer
>> + *
>> + * Copyright (C) 2016 Aleksei Mamlin <mamli...@gmail.com>
>> + * Copyright (c) 2012 Domintech Technology Co., Ltd
>> + *
>> + * This program is free software; you can redistribute it and/or modify it
>> + * under the terms of the GNU General Public License as published by the
>> Free
>> + * Software Foundation; version 2 of the License.
>> + */
>> +
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/i2c.h>
>> +#include <linux/input.h>
>> +#include <linux/input-polldev.h>
>> +#include <linux/irq.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/delay.h>
>> +#include <linux/slab.h>
>> +#include <linux/of.h>
>> +
>> +/* Device data registers */
>> +#define DMARD06_CHIP_ID_REG 0x0f
>> +#define DMARD06_TOUT_REG 0x40
>> +#define DMARD06_XOUT_REG 0x41
>> +#define DMARD06_YOUT_REG 0x42
>> +#define DMARD06_ZOUT_REG 0x43
>> +
>> +/* Device control registers */
>> +#define DMARD06_CTRL_1_REG 0x44
>> +#define DMARD06_CTRL_2_REG 0x45
>> +#define DMARD06_CTRL_3_REG 0x46
>> +#define DMARD06_CTRL_4_REG 0x47
>> +#define DMARD06_CTRL_5_REG 0x48
>> +#define DMARD06_STATUS_REG 0x49
>> +#define DMARD06_INT_CFG_REG 0x4a
>> +#define DMARD06_FILTER_RESET_REG 0x52
>> +#define DMARD06_CHIP_RESET_REG 0x53
>> +
>> +/* Device ID value */
>> +#define DMARD06_CHIP_ID 0x06
>> +
>> +/* Device max value */
>> +#define DMARD06_MAX_VALUE 0x3f
>> +
>> +/* Each axis is represented by a 1-byte data word */
>> +#define DMARD06_XYZ_DATA_SIZE 3
>> +
>> +/* Interrupt sources */
>> +#define DMARD06_INT_SRC1 0x04
>> +#define DMARD06_INT_SRC_BOTH 0x08
>> +#define DMARD06_INT_MOV_DETECT 0x40
>> +#define DMARD06_INT_POS_DETECT 0xc0
>> +
>> +/* Device modes */
>> +#define DMARD06_MODE_NORMAL 0x27
>> +#define DMARD06_MODE_POWERDOWN 0x00
>> +
>> +/* Input poll interval in milliseconds */
>> +#define DMARD06_POLL_INTERVAL 10
>> +#define DMARD06_POLL_MAX 100
>> +#define DMARD06_POLL_MIN 0
>> +
>> +struct dmard06_data {
>> + struct i2c_client *client;
>> + struct input_dev *input;
>> + struct input_polled_dev *input_poll;
>> + unsigned long irq_flags;
>> + int range;
>> + u8 chip_id;
>> + u8 mode;
>> +};
>> +
>> +static int dmard06_i2c_read(struct i2c_client *client, u8 reg, u8 *buf)
>> +{
>> + int error;
>> +
>> + error = i2c_master_send(client, ®, 1);
>> + if (unlikely(error < 0))
>> + return error;
>> +
>> + error = i2c_master_recv(client, buf, 1);
>> + if (unlikely(error < 0))
>> + return error;
>> +
>> + return 0;
>> +}
>> +
>> +static int dmard06_i2c_write(struct i2c_client *client, u8 reg, u8 val)
>> +{
>> + int error;
>> + u8 buf[2] = {reg, val};
>> +
>> + error = i2c_master_send(client, buf, 2);
>> + if (unlikely(error < 0))
>> + return error;
>> +
>> + return 0;
>> +}
>> +
>> +static int dmard06_reset(struct i2c_client *client)
>> +{
>> + u8 buf;
>> + int error;
>> +
>> + error = dmard06_i2c_read(client, DMARD06_CHIP_RESET_REG, &buf);
>> + if (error) {
>> + dev_err(&client->dev, "Failed to reset controller: %d", error);
>> + return error;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int dmard06_set_mode(struct dmard06_data *dmard06, u8 mode)
>> +{
>> + int error;
>> +
>> + error = dmard06_i2c_write(dmard06->client, DMARD06_CTRL_1_REG, mode);
>> + if (error) {
>> + dev_err(&dmard06->client->dev, "Failed to set mode: %d",
>> + error);
>> + return error;
>> + }
>> +
>> + dmard06->mode = mode;
>> +
>> + return 0;
>> +}
>> +
>> +static int dmard06_init_irq(struct i2c_client *client)
>> +{
>> + int error;
>> +
>> + error = dmard06_i2c_write(client, DMARD06_CTRL_4_REG,
>> + DMARD06_INT_SRC1);
>> + if (error) {
>> + dev_err(&client->dev, "Failed to set interrupt source: %d",
>> + error);
>> + return error;
>> + }
>> +
>> + error = dmard06_i2c_write(client, DMARD06_INT_CFG_REG,
>> + DMARD06_INT_POS_DETECT);
>> + if (error) {
>> + dev_err(&client->dev, "Failed to set interrupt event: %d",
>> + error);
>> + return error;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int dmard06_open(struct dmard06_data *dmard06)
>> +{
>> + int error;
>> +
>> + if (dmard06->mode != DMARD06_MODE_NORMAL) {
>> + error = dmard06_set_mode(dmard06, DMARD06_MODE_NORMAL);
>> + if (error)
>> + return error;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void dmard06_close(struct dmard06_data *dmard06)
>> +{
>> + if (dmard06->mode != DMARD06_MODE_POWERDOWN)
>> + dmard06_set_mode(dmard06, DMARD06_MODE_POWERDOWN);
>> +}
>> +
>> +static int dmard06_irq_open(struct input_dev *input)
>> +{
>> + struct dmard06_data *dmard06 = input_get_drvdata(input);
>> +
>> + return dmard06_open(dmard06);
>> +}
>> +
>> +static void dmard06_irq_close(struct input_dev *input)
>> +{
>> + struct dmard06_data *dmard06 = input_get_drvdata(input);
>> +
>> + dmard06_close(dmard06);
>> +}
>> +
>> +static void dmard06_poll_open(struct input_polled_dev *input_poll)
>> +{
>> + struct dmard06_data *dmard06 = input_poll->private;
>> +
>> + dmard06_open(dmard06);
>> +}
>> +
>> +static void dmard06_poll_close(struct input_polled_dev *input_poll)
>> +{
>> + struct dmard06_data *dmard06 = input_poll->private;
>> +
>> + dmard06_close(dmard06);
>> +}
>> +
>> +static int dmard06_read_chip_id(struct dmard06_data *dmard06)
>> +{
>> + u8 buf;
>> + u8 chip_id;
>> + int error;
>> +
>> + error = dmard06_i2c_read(dmard06->client, DMARD06_CHIP_ID_REG, &buf);
>> + if (error) {
>> + dev_err(&dmard06->client->dev, "Failed to read chip id: %d\n",
>> + error);
>> + return error;
>> + }
>> +
>> + chip_id = (buf & 0x00ff);
>> + if (chip_id != DMARD06_CHIP_ID) {
>> + dev_err(&dmard06->client->dev, "Unknown chip id: %02x\n",
>> + chip_id);
>> + return -EINVAL;
>> + }
>> +
>> + dmard06->chip_id = chip_id;
>> + dev_info(&dmard06->client->dev, "Found DMARD%02x chip\n", chip_id);
>> +
>> + return 0;
>> +}
>> +
>> +static void dmard06_report_xyz(struct dmard06_data *dmard06)
>> +{
>> + u8 axis[DMARD06_XYZ_DATA_SIZE];
>> + bool reversed;
>> + int xyz[3];
>> + int error;
>> + int i;
>> +
>> + error = i2c_smbus_read_i2c_block_data(dmard06->client,
>> + DMARD06_XOUT_REG,
>> + DMARD06_XYZ_DATA_SIZE, axis);
>> + if (error != DMARD06_XYZ_DATA_SIZE)
>> + return;
>> +
>> + for (i = 0; i < DMARD06_XYZ_DATA_SIZE; i++) {
>> + reversed = (axis[i] >> 7) & 1;
>> + xyz[i] = (int)((axis[i] & 0x7f) >> 1);
>> + if (reversed)
>> + xyz[i] = xyz[i] - dmard06->range;
>> + }
>> +
>> + input_report_abs(dmard06->input, ABS_X, xyz[0]);
>> + input_report_abs(dmard06->input, ABS_Y, xyz[1]);
>> + input_report_abs(dmard06->input, ABS_Z, xyz[2]);
>> + input_sync(dmard06->input);
>> +}
>> +
>> +static irqreturn_t dmard06_irq_handler(int irq, void *dev_id)
>> +{
>> + struct dmard06_data *dmard06 = dev_id;
>> +
>> + dmard06_report_xyz(dmard06);
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static void dmard06_poll(struct input_polled_dev *input_poll)
>> +{
>> + dmard06_report_xyz(input_poll->private);
>> +}
>> +
>> +static void dmard06_init_input_device(struct dmard06_data *dmard06,
>> + struct input_dev *input)
>> +{
>> + int range;
>> +
>> + input->name = "dmard06";
>> + input->id.bustype = BUS_I2C;
>> + input->id.version = dmard06->chip_id;
>> + input->dev.parent = &dmard06->client->dev;
>> +
>> + set_bit(EV_ABS, input->evbit);
>> +
>> + range = DMARD06_MAX_VALUE;
>> + input_set_abs_params(input, ABS_X, -range, range, 0, 0);
>> + input_set_abs_params(input, ABS_Y, -range, range, 0, 0);
>> + input_set_abs_params(input, ABS_Z, -range, range, 0, 0);
>> +
>> + dmard06->range = range;
>> +}
>> +
>> +static int dmard06_request_input_device(struct dmard06_data *dmard06)
>> +{
>> + struct input_dev *input;
>> + int error;
>> +
>> + input = devm_input_allocate_device(&dmard06->client->dev);
>> + if (!input) {
>> + dev_err(&dmard06->client->dev,
>> + "Failed to allocate input device\n");
>> + return -ENOMEM;
>> + }
>> +
>> + dmard06_init_input_device(dmard06, input);
>> +
>> + input->open = dmard06_irq_open;
>> + input->close = dmard06_irq_close;
>> + input_set_drvdata(input, dmard06);
>> +
>> + error = input_register_device(input);
>> + if (error) {
>> + dev_err(&dmard06->client->dev,
>> + "Failed to register input device: %d", error);
>> + return error;
>> + }
>> +
>> + dmard06->input = input;
>> +
>> + return 0;
>> +}
>> +
>> +static int dmard06_request_polled_device(struct dmard06_data *dmard06)
>> +{
>> + struct input_polled_dev *input_poll;
>> + int error;
>> +
>> + input_poll = devm_input_allocate_polled_device(&dmard06->client->dev);
>> + if (!input_poll) {
>> + dev_err(&dmard06->client->dev,
>> + "Failed to allocate polled input device\n");
>> + return -ENOMEM;
>> + }
>> +
>> + input_poll->private = dmard06;
>> + input_poll->open = dmard06_poll_open;
>> + input_poll->close = dmard06_poll_close;
>> + input_poll->poll = dmard06_poll;
>> + input_poll->poll_interval = DMARD06_POLL_INTERVAL;
>> + input_poll->poll_interval_min = DMARD06_POLL_MIN;
>> + input_poll->poll_interval_max = DMARD06_POLL_MAX;
>> +
>> + dmard06_init_input_device(dmard06, input_poll->input);
>> +
>> + error = input_register_polled_device(input_poll);
>> + if (error) {
>> + dev_err(&dmard06->client->dev,
>> + "Failed to register polled device: %d", error);
>> + return error;
>> + }
>> +
>> + dmard06->input_poll = input_poll;
>> + dmard06->input = input_poll->input;
>> +
>> + return 0;
>> +}
>> +
>> +static int dmard06_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct dmard06_data *dmard06;
>> + int error;
>> +
>> + dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
>> +
>> + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
>> + dev_err(&client->dev, "I2C check functionality failed\n");
>> + return -ENXIO;
>> + }
>> +
>> + dmard06 = devm_kzalloc(&client->dev, sizeof(*dmard06), GFP_KERNEL);
>> + if (!dmard06)
>> + return -ENOMEM;
>> +
>> + dmard06->client = client;
>> + i2c_set_clientdata(client, dmard06);
>> +
>> + error = dmard06_reset(dmard06->client);
>> + if (error)
>> + return error;
>> +
>> + error = dmard06_read_chip_id(dmard06);
>> + if (error)
>> + return error;
>> +
>> + error = dmard06_set_mode(dmard06, DMARD06_MODE_NORMAL);
>> + if (error)
>> + return error;
>> +
>> + if (dmard06->client->irq) {
>> + error = dmard06_init_irq(dmard06->client);
>> + if (error)
>> + return error;
>> +
>> + error = dmard06_request_input_device(dmard06);
>> + if (error)
>> + return error;
>> +
>> + dmard06->irq_flags = IRQ_TYPE_LEVEL_LOW | IRQF_ONESHOT;
>> + error = devm_request_threaded_irq(&dmard06->client->dev,
>> + dmard06->client->irq, NULL,
>> + dmard06_irq_handler,
>> + dmard06->irq_flags,
>> + dmard06->client->name,
>> + dmard06);
>> + if (error) {
>> + dev_err(&dmard06->client->dev,
>> + "Request IRQ failed: %d\n", error);
>> + return error;
>> + }
>> +
>> + } else {
>> + error = dmard06_request_polled_device(dmard06);
>> + if (error)
>> + return error;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const struct i2c_device_id dmard06_id[] = {
>> + { "dmard06", 0 },
>> + { }
>> +};
>> +MODULE_DEVICE_TABLE(i2c, dmard06_id);
>> +
>> +static const struct of_device_id dmard06_of_match[] = {
>> + { .compatible = "domintech,dmard06" },
>> + { }
>> +};
>> +MODULE_DEVICE_TABLE(of, dmard06_of_match);
>> +
>> +static struct i2c_driver dmard06_driver = {
>> + .probe = dmard06_probe,
>> + .class = I2C_CLASS_HWMON,
>> + .id_table = dmard06_id,
>> + .driver = {
>> + .name = "dmard06",
>> + .of_match_table = of_match_ptr(dmard06_of_match),
>> + },
>> +};
>> +module_i2c_driver(dmard06_driver);
>> +
>> +MODULE_AUTHOR("Aleksei Mamlin <mamli...@gmail.com>");
>> +MODULE_DESCRIPTION("Domintech DMARD06 accelerometer driver");
>> +MODULE_LICENSE("GPL v2");
>> --
>> 2.7.3
>>
>
