> -----Original Message----- > From: Alexandre Belloni [mailto:alexandre.bell...@free-electrons.com] > Sent: 2016年11月21日 22:03 > To: Wenyou Yang - A41535 <wenyou.y...@microchip.com> > Cc: Nicolas Ferre <nicolas.fe...@atmel.com>; Russell King > <li...@arm.linux.org.uk>; Rob Herring <robh...@kernel.org>; Pawel Moll > <pawel.m...@arm.com>; Mark Rutland <mark.rutl...@arm.com>; Ian Campbell > <ijc+devicet...@hellion.org.uk>; Kumar Gala <ga...@codeaurora.org>; linux- > ker...@vger.kernel.org; Wenyou Yang - A41535 > <wenyou.y...@microchip.com>; devicet...@vger.kernel.org; linux-arm- > ker...@lists.infradead.org > Subject: Re: [PATCH v3] ARM: at91/dt: add dts file for sama5d36ek CMP board > > Hi, > > I fixed it up this time but please use the proper subject prefix next time > (ARM: dts: > at91:).
Thank you. I keep it in mind. > > On 21/11/2016 at 13:14:42 +0800, Wenyou Yang wrote : > > The sama5d36ek CMP board is the variant of sama5d3xek board. > > It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and some > > power rail. Its main purpose is used to measure the power consumption. > > The difference of the sama5d36ek CMP dts from sama5d36ek dts is listed > > as below. > > 1. The USB host nodes are removed, that is, the USB host is disabled. > > 2. The gpio_keys node is added to wake up from the sleep. > > 3. The LCD isn't supported due to the pins for LCD are conflicted > > with gpio_keys. > > 4. The adc0 node support the pinctrl sleep state to fix the over > > consumption on VDDANA. > > > > As said in errata, "When the USB host ports are used in high speed > > mode (EHCI), it is not possible to suspend the ports if no device is > > attached on each port. This leads to increased power consumption even > > if the system is in a low power mode." That is why the the USB host is > > disabled. > > > > Signed-off-by: Wenyou Yang <wenyou.y...@atmel.com> > > --- > > > > Changes in v3: > > - Use a dual license scheme for DT files. > > - Use the proper model name and the compatible string to reflect > > the nature of this new "CMP" board. > > - Change name of wakeup property to "wakeup-source". > > - Remove unnecessary comments. > > - Remove bootargs. > > > > Changes in v2: > > - Add the pinctrl sleep state for adc0 node to fix the over > > consumption on VDDANA. > > - Improve the commit log. > > > > arch/arm/boot/dts/sama5d36ek_cmp.dts | 87 ++++++++++ > > arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 201 +++++++++++++++++++++++ > > arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 301 > > ++++++++++++++++++++++++++++++++++ > > 3 files changed, 589 insertions(+) > > create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts > > create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi > > create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi > > > Applied, thanks. > > -- > Alexandre Belloni, Free Electrons > Embedded Linux and Kernel engineering > http://free-electrons.com Best Regards, Wenyou Yang