Hello lkml, I have problem in the communication between Adaptec:
02:09.0 SCSI storage controller: Adaptec AIC-7892B U160/m (rev 02) which is driven by aic7xxx driver. Kernel version is 2.6.13.1 Tape is ECRIX: Vendor: ECRIX Model: VXA-1 Rev: 2C8C Type: Sequential-Access ANSI SCSI revision: 02 I've found in the logs this messages: Mar 7 07:47:53 rek kernel: st0: Error with sense data: <6>st0: Current: sense key=0x4 Mar 7 07:47:53 rek kernel: ASC=0x44 ASCQ=0x0 Mar 7 07:47:53 rek kernel: Info fld=0x0 Mar 7 07:47:59 rek kernel: st0: Error with sense data: <6>st0: Current: sense key=0x4 Mar 7 07:47:59 rek kernel: ASC=0x15 ASCQ=0x1 Mar 7 07:47:59 rek kernel: Info fld=0x0 Mar 7 07:47:59 rek kernel: st0: Error on write filemark. Mar 7 07:48:15 rek kernel: st0: Error with sense data: <6>st0: Current: sense key=0x4 Mar 7 07:48:15 rek kernel: ASC=0x15 ASCQ=0x1 Mar 7 07:48:15 rek kernel: Info fld=0x1 Mar 7 08:06:48 rek kernel: scsi0:0:1:0: Attempting to queue an ABORT message Mar 7 08:06:48 rek kernel: CDB: 0x8 0x0 0x0 0x80 0x0 0x0 Mar 7 08:06:48 rek kernel: scsi0: At time of recovery, card was not paused Mar 7 08:06:48 rek kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<< Mar 7 08:06:48 rek kernel: scsi0: Dumping Card State while idle, at SEQADDR 0x9 Mar 7 08:06:48 rek kernel: Card was paused Mar 7 08:06:48 rek kernel: ACCUM = 0x4, SINDEX = 0x17, DINDEX = 0x22, ARG_2 = 0x0 Mar 7 08:06:48 rek kernel: HCNT = 0x0 SCBPTR = 0x0 Mar 7 08:06:48 rek kernel: SCSIPHASE[0x0] SCSISIGI[0x0] ERROR[0x0] SCSIBUSL[0x0] Mar 7 08:06:48 rek kernel: LASTPHASE[0x1]:(P_BUSFREE) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) Mar 7 08:06:48 rek kernel: SBLKCTL[0xa]:(SELWIDE|SELBUSB) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE) Mar 7 08:06:48 rek kernel: SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) SSTAT0[0x0] Mar 7 08:06:48 rek kernel: SSTAT1[0x8]:(BUSFREE) SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8]:(ENSWRAP) Mar 7 08:06:48 rek kernel: SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) Mar 7 08:06:48 rek kernel: SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) Mar 7 08:06:48 rek kernel: STACK: 0x0 0x163 0x178 0x3 Mar 7 08:06:48 rek kernel: SCB count = 4 Mar 7 08:06:48 rek kernel: Kernel NEXTQSCB = 2 Mar 7 08:06:48 rek kernel: Card NEXTQSCB = 2 Mar 7 08:06:48 rek kernel: QINFIFO entries: Mar 7 08:06:48 rek kernel: Waiting Queue entries: Mar 7 08:06:48 rek kernel: Disconnected Queue entries: 0:3 Mar 7 08:06:48 rek kernel: QOUTFIFO entries: Mar 7 08:06:48 rek kernel: Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Mar 7 08:06:48 rek kernel: Sequencer SCB Info: Mar 7 08:06:48 rek kernel: 0 SCB_CONTROL[0x44]:(DISCONNECTED|DISCENB) SCB_SCSIID[0x17] Mar 7 08:06:48 rek kernel: SCB_LUN[0x0] SCB_TAG[0x3] Mar 7 08:06:48 rek kernel: 1 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) ... Mar 7 08:06:48 rek kernel: 30 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) Mar 7 08:06:48 rek kernel: SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] Mar 7 08:06:48 rek kernel: 31 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) Mar 7 08:06:48 rek kernel: SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] Mar 7 08:06:48 rek kernel: Pending list: Mar 7 08:06:48 rek kernel: 3 SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0x17] SCB_LUN[0x0] Mar 7 08:06:48 rek kernel: Kernel Free SCB list: 1 0 Mar 7 08:06:48 rek kernel: Untagged Q(1): 3 Mar 7 08:06:48 rek kernel: Mar 7 08:06:48 rek kernel: <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>> Mar 7 08:06:48 rek kernel: (scsi0:A:1:0): Device is disconnected, re-queuing SCB Mar 7 08:06:48 rek kernel: Recovery code sleeping Mar 7 08:06:48 rek kernel: (scsi0:A:1:0): Abort Message Sent Mar 7 08:06:48 rek kernel: (scsi0:A:1:0): SCB 3 - Abort Completed. Mar 7 08:06:48 rek kernel: Recovery SCB completes Mar 7 08:06:48 rek kernel: Recovery code awake Mar 7 08:06:48 rek kernel: aic7xxx_abort returns 0x2002 Mar 7 08:06:50 rek kernel: (scsi0:A:1:0): Unexpected busfree in Command phase Mar 7 08:06:50 rek kernel: SEQADDR == 0x16b Mar 7 08:06:50 rek kernel: scsi0:0:1:0: Attempting to queue a TARGET RESET message Mar 7 08:06:50 rek kernel: CDB: 0x8 0x0 0x0 0x80 0x0 0x0 Mar 7 08:06:50 rek kernel: scsi0:0:1:0: Command not found Mar 7 08:06:50 rek kernel: aic7xxx_dev_reset returns 0x2002 Mar 7 08:06:50 rek kernel: (scsi0:A:1:0): refuses WIDE negotiation. Using 8bit transfers Mar 7 08:06:50 rek kernel: target0:0:1: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 32) Mar 7 08:06:50 rek kernel: (scsi0:A:1:0): Unexpected busfree in Message-in phase Mar 7 08:06:50 rek kernel: SEQADDR == 0x16b Mar 7 08:07:00 rek kernel: scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 1 lun 0 Mar 7 08:07:00 rek kernel: st0: Error 30000 (sugg. bt 0x0, driver bt 0x0, host bt 0x3). Please, can you advice me, where is problem? I have changed SCSI cable with proper active terminator... Thank you very much. Sincerely Jan Marek - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
