There are some variations from mt2701 to mt2712:
1. banks shared by multiple ports are put back into each port,
such as SPLLC and U2FREQ;
2. add a new bank MISC for u2port, and CHIP for u3port;
3. bank's offset in each port are also rearranged;
Signed-off-by: Chunfeng Yun <chunfeng....@mediatek.com>
---
drivers/phy/phy-mt65xx-usb3.c | 326 ++++++++++++++++++++++++++---------------
1 file changed, 208 insertions(+), 118 deletions(-)
diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
index c187a3b..d515c69 100644
--- a/drivers/phy/phy-mt65xx-usb3.c
+++ b/drivers/phy/phy-mt65xx-usb3.c
@@ -23,46 +23,54 @@
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
-/*
- * for sifslv2 register, but exclude port's;
- * relative to USB3_SIF2_BASE base address
- */
-#define SSUSB_SIFSLV_SPLLC 0x0000
-#define SSUSB_SIFSLV_U2FREQ 0x0100
-
-/* offsets of banks in each u2phy registers */
-#define SSUSB_SIFSLV_U2PHY_COM_BASE 0x0000
-/* offsets of banks in each u3phy registers */
-#define SSUSB_SIFSLV_U3PHYD_BASE 0x0000
-#define SSUSB_SIFSLV_U3PHYA_BASE 0x0200
-
-#define U3P_USBPHYACR0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
+/* version V1 sub-banks offset base address */
+/* banks shared by multiple phys */
+#define SSUSB_SIFSLV_V1_SPLLC 0x000 /* shared by u3 phys */
+#define SSUSB_SIFSLV_V1_U2FREQ 0x100 /* shared by u2 phys */
+/* u2 phy bank */
+#define SSUSB_SIFSLV_V1_U2PHY_COM 0x000
+/* u3 phy banks */
+#define SSUSB_SIFSLV_V1_U3PHYD 0x000
+#define SSUSB_SIFSLV_V1_U3PHYA 0x200
+
+/* version V2 sub-banks offset base address */
+/* u2 phy banks */
+#define SSUSB_SIFSLV_V2_MISC 0x000
+#define SSUSB_SIFSLV_V2_U2FREQ 0x100
+#define SSUSB_SIFSLV_V2_U2PHY_COM 0x300
+/* u3 phy banks */
+#define SSUSB_SIFSLV_V2_SPLLC 0x000
+#define SSUSB_SIFSLV_V2_CHIP 0x100
+#define SSUSB_SIFSLV_V2_U3PHYD 0x200
+#define SSUSB_SIFSLV_V2_U3PHYA 0x400
+
+#define U3P_USBPHYACR0 0x000
#define PA0_RG_U2PLL_FORCE_ON BIT(15)
-#define U3P_USBPHYACR2 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
+#define U3P_USBPHYACR2 0x008
#define PA2_RG_SIF_U2PLL_FORCE_EN BIT(18)
-#define U3P_USBPHYACR5 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
+#define U3P_USBPHYACR5 0x014
#define PA5_RG_U2_HSTX_SRCAL_EN BIT(15)
#define PA5_RG_U2_HSTX_SRCTRL GENMASK(14, 12)
#define PA5_RG_U2_HSTX_SRCTRL_VAL(x) ((0x7 & (x)) << 12)
#define PA5_RG_U2_HS_100U_U3_EN BIT(11)
-#define U3P_USBPHYACR6 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
+#define U3P_USBPHYACR6 0x018
#define PA6_RG_U2_BC11_SW_EN BIT(23)
#define PA6_RG_U2_OTG_VBUSCMP_EN BIT(20)
#define PA6_RG_U2_SQTH GENMASK(3, 0)
#define PA6_RG_U2_SQTH_VAL(x) (0xf & (x))
-#define U3P_U2PHYACR4 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
+#define U3P_U2PHYACR4 0x020
#define P2C_RG_USB20_GPIO_CTL BIT(9)
#define P2C_USB20_GPIO_MODE BIT(8)
#define P2C_U2_GPIO_CTR_MSK (P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
-#define U3D_U2PHYDCR0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
+#define U3D_U2PHYDCR0 0x060
#define P2C_RG_SIF_U2PLL_FORCE_ON BIT(24)
-#define U3P_U2PHYDTM0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
+#define U3P_U2PHYDTM0 0x068
#define P2C_FORCE_UART_EN BIT(26)
#define P2C_FORCE_DATAIN BIT(23)
#define P2C_FORCE_DM_PULLDOWN BIT(21)
@@ -84,47 +92,44 @@
P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
-#define U3P_U2PHYDTM1 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
+#define U3P_U2PHYDTM1 0x06C
#define P2C_RG_UART_EN BIT(16)
#define P2C_RG_VBUSVALID BIT(5)
#define P2C_RG_SESSEND BIT(4)
#define P2C_RG_AVALID BIT(2)
-#define U3P_U3_PHYA_REG0 (SSUSB_SIFSLV_U3PHYA_BASE + 0x0000)
-#define P3A_RG_U3_VUSB10_ON BIT(5)
-
-#define U3P_U3_PHYA_REG6 (SSUSB_SIFSLV_U3PHYA_BASE + 0x0018)
+#define U3P_U3_PHYA_REG6 0x018
#define P3A_RG_TX_EIDLE_CM GENMASK(31, 28)
#define P3A_RG_TX_EIDLE_CM_VAL(x) ((0xf & (x)) << 28)
-#define U3P_U3_PHYA_REG9 (SSUSB_SIFSLV_U3PHYA_BASE + 0x0024)
+#define U3P_U3_PHYA_REG9 0x024
#define P3A_RG_RX_DAC_MUX GENMASK(5, 1)
#define P3A_RG_RX_DAC_MUX_VAL(x) ((0x1f & (x)) << 1)
-#define U3P_U3PHYA_DA_REG0 (SSUSB_SIFSLV_U3PHYA_BASE + 0x0100)
+#define U3P_U3_PHYA_DA_REG0 0x100
#define P3A_RG_XTAL_EXT_EN_U3 GENMASK(11, 10)
#define P3A_RG_XTAL_EXT_EN_U3_VAL(x) ((0x3 & (x)) << 10)
-#define U3P_PHYD_CDR1 (SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
+#define U3P_U3_PHYD_CDR1 0x05c
#define P3D_RG_CDR_BIR_LTD1 GENMASK(28, 24)
#define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24)
#define P3D_RG_CDR_BIR_LTD0 GENMASK(12, 8)
#define P3D_RG_CDR_BIR_LTD0_VAL(x) ((0x1f & (x)) << 8)
-#define U3P_XTALCTL3 (SSUSB_SIFSLV_SPLLC + 0x0018)
+#define U3P_SPLLC_XTALCTL3 0x018
#define XC3_RG_U3_XTAL_RX_PWD BIT(9)
#define XC3_RG_U3_FRC_XTAL_RX_PWD BIT(8)
-#define U3P_U2FREQ_FMCR0 (SSUSB_SIFSLV_U2FREQ + 0x00)
+#define U3P_U2FREQ_FMCR0 0x00
#define P2F_RG_MONCLK_SEL GENMASK(27, 26)
#define P2F_RG_MONCLK_SEL_VAL(x) ((0x3 & (x)) << 26)
#define P2F_RG_FREQDET_EN BIT(24)
#define P2F_RG_CYCLECNT GENMASK(23, 0)
#define P2F_RG_CYCLECNT_VAL(x) ((P2F_RG_CYCLECNT) & (x))
-#define U3P_U2FREQ_VALUE (SSUSB_SIFSLV_U2FREQ + 0x0c)
+#define U3P_U2FREQ_VALUE 0x0c
-#define U3P_U2FREQ_FMMONR1 (SSUSB_SIFSLV_U2FREQ + 0x10)
+#define U3P_U2FREQ_FMMONR1 0x10
#define P2F_USB_FM_VALID BIT(0)
#define P2F_RG_FRCK_EN BIT(8)
@@ -133,14 +138,37 @@
#define U3P_SR_COEF_DIVISOR 1000
#define U3P_FM_DET_CYCLE_CNT 1024
+enum mt_phy_version {
+ MT_PHY_V1 = 1,
+ MT_PHY_V2,
+};
+
struct mt65xx_phy_pdata {
/* avoid RX sensitivity level degradation only for mt8173 */
bool avoid_rx_sen_degradation;
+ enum mt_phy_version version;
+};
+
+struct u2phy_banks {
+ void __iomem *misc;
+ void __iomem *fmreg;
+ void __iomem *com;
+};
+
+struct u3phy_banks {
+ void __iomem *spllc;
+ void __iomem *chip;
+ void __iomem *phyd; /* include u3phyd_bank2 */
+ void __iomem *phya; /* include u3phya_da */
};
struct mt65xx_phy_instance {
struct phy *phy;
void __iomem *port_base;
+ union {
+ struct u2phy_banks u2_banks;
+ struct u3phy_banks u3_banks;
+ };
u32 index;
u8 type;
};
@@ -158,49 +186,53 @@ struct mt65xx_u3phy {
static void hs_slew_rate_calibrate(struct mt65xx_u3phy *u3phy,
struct mt65xx_phy_instance *instance)
{
- void __iomem *sif_base = u3phy->sif_base;
+ struct u2phy_banks *u2_banks = &instance->u2_banks;
+ void __iomem *fmreg = u2_banks->fmreg;
+ void __iomem *com = u2_banks->com;
int calibration_val;
int fm_out;
u32 tmp;
/* enable USB ring oscillator */
- tmp = readl(instance->port_base + U3P_USBPHYACR5);
+ tmp = readl(com + U3P_USBPHYACR5);
tmp |= PA5_RG_U2_HSTX_SRCAL_EN;
- writel(tmp, instance->port_base + U3P_USBPHYACR5);
+ writel(tmp, com + U3P_USBPHYACR5);
udelay(1);
/*enable free run clock */
- tmp = readl(sif_base + U3P_U2FREQ_FMMONR1);
+ tmp = readl(fmreg + U3P_U2FREQ_FMMONR1);
tmp |= P2F_RG_FRCK_EN;
- writel(tmp, sif_base + U3P_U2FREQ_FMMONR1);
+ writel(tmp, fmreg + U3P_U2FREQ_FMMONR1);
/* set cycle count as 1024, and select u2 channel */
- tmp = readl(sif_base + U3P_U2FREQ_FMCR0);
+ tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
tmp &= ~(P2F_RG_CYCLECNT | P2F_RG_MONCLK_SEL);
tmp |= P2F_RG_CYCLECNT_VAL(U3P_FM_DET_CYCLE_CNT);
- tmp |= P2F_RG_MONCLK_SEL_VAL(instance->index >> 1);
- writel(tmp, sif_base + U3P_U2FREQ_FMCR0);
+ if (u3phy->pdata->version == MT_PHY_V1)
+ tmp |= P2F_RG_MONCLK_SEL_VAL(instance->index >> 1);
+
+ writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
/* enable frequency meter */
- tmp = readl(sif_base + U3P_U2FREQ_FMCR0);
+ tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
tmp |= P2F_RG_FREQDET_EN;
- writel(tmp, sif_base + U3P_U2FREQ_FMCR0);
+ writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
/* ignore return value */
- readl_poll_timeout(sif_base + U3P_U2FREQ_FMMONR1, tmp,
+ readl_poll_timeout(fmreg + U3P_U2FREQ_FMMONR1, tmp,
(tmp & P2F_USB_FM_VALID), 10, 200);
- fm_out = readl(sif_base + U3P_U2FREQ_VALUE);
+ fm_out = readl(fmreg + U3P_U2FREQ_VALUE);
/* disable frequency meter */
- tmp = readl(sif_base + U3P_U2FREQ_FMCR0);
+ tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
tmp &= ~P2F_RG_FREQDET_EN;
- writel(tmp, sif_base + U3P_U2FREQ_FMCR0);
+ writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
/*disable free run clock */
- tmp = readl(sif_base + U3P_U2FREQ_FMMONR1);
+ tmp = readl(fmreg + U3P_U2FREQ_FMMONR1);
tmp &= ~P2F_RG_FRCK_EN;
- writel(tmp, sif_base + U3P_U2FREQ_FMMONR1);
+ writel(tmp, fmreg + U3P_U2FREQ_FMMONR1);
if (fm_out) {
/* ( 1024 / FM_OUT ) x reference clock frequency x 0.028 */
@@ -215,48 +247,48 @@ static void hs_slew_rate_calibrate(struct mt65xx_u3phy
*u3phy,
instance->index, fm_out, calibration_val);
/* set HS slew rate */
- tmp = readl(instance->port_base + U3P_USBPHYACR5);
+ tmp = readl(com + U3P_USBPHYACR5);
tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(calibration_val);
- writel(tmp, instance->port_base + U3P_USBPHYACR5);
+ writel(tmp, com + U3P_USBPHYACR5);
/* disable USB ring oscillator */
- tmp = readl(instance->port_base + U3P_USBPHYACR5);
+ tmp = readl(com + U3P_USBPHYACR5);
tmp &= ~PA5_RG_U2_HSTX_SRCAL_EN;
- writel(tmp, instance->port_base + U3P_USBPHYACR5);
+ writel(tmp, com + U3P_USBPHYACR5);
}
static void u3_phy_instance_init(struct mt65xx_u3phy *u3phy,
struct mt65xx_phy_instance *instance)
{
- void __iomem *port_base = instance->port_base;
+ struct u3phy_banks *u3_banks = &instance->u3_banks;
u32 tmp;
/* gating PCIe Analog XTAL clock */
- tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
+ tmp = readl(u3_banks->spllc + U3P_SPLLC_XTALCTL3);
tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
- writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
+ writel(tmp, u3_banks->spllc + U3P_SPLLC_XTALCTL3);
/* gating XSQ */
- tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
+ tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG0);
tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
- writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
+ writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG0);
- tmp = readl(port_base + U3P_U3_PHYA_REG9);
+ tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG9);
tmp &= ~P3A_RG_RX_DAC_MUX;
tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
- writel(tmp, port_base + U3P_U3_PHYA_REG9);
+ writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG9);
- tmp = readl(port_base + U3P_U3_PHYA_REG6);
+ tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG6);
tmp &= ~P3A_RG_TX_EIDLE_CM;
tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
- writel(tmp, port_base + U3P_U3_PHYA_REG6);
+ writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG6);
- tmp = readl(port_base + U3P_PHYD_CDR1);
+ tmp = readl(u3_banks->phyd + U3P_U3_PHYD_CDR1);
tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
- writel(tmp, port_base + U3P_PHYD_CDR1);
+ writel(tmp, u3_banks->phyd + U3P_U3_PHYD_CDR1);
dev_dbg(u3phy->dev, "%s(%d)\n", __func__, instance->index);
}
@@ -264,51 +296,52 @@ static void u3_phy_instance_init(struct mt65xx_u3phy
*u3phy,
static void phy_instance_init(struct mt65xx_u3phy *u3phy,
struct mt65xx_phy_instance *instance)
{
- void __iomem *port_base = instance->port_base;
+ struct u2phy_banks *u2_banks = &instance->u2_banks;
+ void __iomem *com = u2_banks->com;
u32 index = instance->index;
u32 tmp;
/* switch to USB function. (system register, force ip into usb mode) */
- tmp = readl(port_base + U3P_U2PHYDTM0);
+ tmp = readl(com + U3P_U2PHYDTM0);
tmp &= ~P2C_FORCE_UART_EN;
tmp |= P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0);
- writel(tmp, port_base + U3P_U2PHYDTM0);
+ writel(tmp, com + U3P_U2PHYDTM0);
- tmp = readl(port_base + U3P_U2PHYDTM1);
+ tmp = readl(com + U3P_U2PHYDTM1);
tmp &= ~P2C_RG_UART_EN;
- writel(tmp, port_base + U3P_U2PHYDTM1);
+ writel(tmp, com + U3P_U2PHYDTM1);
if (!index) {
- tmp = readl(port_base + U3P_U2PHYACR4);
+ tmp = readl(com + U3P_U2PHYACR4);
tmp &= ~P2C_U2_GPIO_CTR_MSK;
- writel(tmp, port_base + U3P_U2PHYACR4);
+ writel(tmp, com + U3P_U2PHYACR4);
}
if (u3phy->pdata->avoid_rx_sen_degradation) {
if (!index) {
- tmp = readl(port_base + U3P_USBPHYACR2);
+ tmp = readl(com + U3P_USBPHYACR2);
tmp |= PA2_RG_SIF_U2PLL_FORCE_EN;
- writel(tmp, port_base + U3P_USBPHYACR2);
+ writel(tmp, com + U3P_USBPHYACR2);
- tmp = readl(port_base + U3D_U2PHYDCR0);
+ tmp = readl(com + U3D_U2PHYDCR0);
tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
- writel(tmp, port_base + U3D_U2PHYDCR0);
+ writel(tmp, com + U3D_U2PHYDCR0);
} else {
- tmp = readl(port_base + U3D_U2PHYDCR0);
+ tmp = readl(com + U3D_U2PHYDCR0);
tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
- writel(tmp, port_base + U3D_U2PHYDCR0);
+ writel(tmp, com + U3D_U2PHYDCR0);
- tmp = readl(port_base + U3P_U2PHYDTM0);
+ tmp = readl(com + U3P_U2PHYDTM0);
tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
- writel(tmp, port_base + U3P_U2PHYDTM0);
+ writel(tmp, com + U3P_U2PHYDTM0);
}
}
- tmp = readl(port_base + U3P_USBPHYACR6);
+ tmp = readl(com + U3P_USBPHYACR6);
tmp &= ~PA6_RG_U2_BC11_SW_EN; /* DP/DM BC1.1 path Disable */
tmp &= ~PA6_RG_U2_SQTH;
tmp |= PA6_RG_U2_SQTH_VAL(2);
- writel(tmp, port_base + U3P_USBPHYACR6);
+ writel(tmp, com + U3P_USBPHYACR6);
dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
}
@@ -316,41 +349,42 @@ static void phy_instance_init(struct mt65xx_u3phy *u3phy,
static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
struct mt65xx_phy_instance *instance)
{
- void __iomem *port_base = instance->port_base;
+ struct u2phy_banks *u2_banks = &instance->u2_banks;
+ void __iomem *com = u2_banks->com;
u32 index = instance->index;
u32 tmp;
/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
- tmp = readl(port_base + U3P_U2PHYDTM0);
+ tmp = readl(com + U3P_U2PHYDTM0);
tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
- writel(tmp, port_base + U3P_U2PHYDTM0);
+ writel(tmp, com + U3P_U2PHYDTM0);
/* OTG Enable */
- tmp = readl(port_base + U3P_USBPHYACR6);
+ tmp = readl(com + U3P_USBPHYACR6);
tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
- writel(tmp, port_base + U3P_USBPHYACR6);
+ writel(tmp, com + U3P_USBPHYACR6);
if (!index) {
/* switch 100uA current to SSUSB */
- tmp = readl(port_base + U3P_USBPHYACR5);
+ tmp = readl(com + U3P_USBPHYACR5);
tmp |= PA5_RG_U2_HS_100U_U3_EN;
- writel(tmp, port_base + U3P_USBPHYACR5);
+ writel(tmp, com + U3P_USBPHYACR5);
}
- tmp = readl(port_base + U3P_U2PHYDTM1);
+ tmp = readl(com + U3P_U2PHYDTM1);
tmp |= P2C_RG_VBUSVALID | P2C_RG_AVALID;
tmp &= ~P2C_RG_SESSEND;
- writel(tmp, port_base + U3P_U2PHYDTM1);
+ writel(tmp, com + U3P_U2PHYDTM1);
if (u3phy->pdata->avoid_rx_sen_degradation && index) {
- tmp = readl(port_base + U3D_U2PHYDCR0);
+ tmp = readl(com + U3D_U2PHYDCR0);
tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
- writel(tmp, port_base + U3D_U2PHYDCR0);
+ writel(tmp, com + U3D_U2PHYDCR0);
- tmp = readl(port_base + U3P_U2PHYDTM0);
+ tmp = readl(com + U3P_U2PHYDTM0);
tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
- writel(tmp, port_base + U3P_U2PHYDTM0);
+ writel(tmp, com + U3P_U2PHYDTM0);
}
dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
}
@@ -358,42 +392,43 @@ static void phy_instance_power_on(struct mt65xx_u3phy
*u3phy,
static void phy_instance_power_off(struct mt65xx_u3phy *u3phy,
struct mt65xx_phy_instance *instance)
{
- void __iomem *port_base = instance->port_base;
+ struct u2phy_banks *u2_banks = &instance->u2_banks;
+ void __iomem *com = u2_banks->com;
u32 index = instance->index;
u32 tmp;
- tmp = readl(port_base + U3P_U2PHYDTM0);
+ tmp = readl(com + U3P_U2PHYDTM0);
tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN);
tmp |= P2C_FORCE_SUSPENDM;
- writel(tmp, port_base + U3P_U2PHYDTM0);
+ writel(tmp, com + U3P_U2PHYDTM0);
/* OTG Disable */
- tmp = readl(port_base + U3P_USBPHYACR6);
+ tmp = readl(com + U3P_USBPHYACR6);
tmp &= ~PA6_RG_U2_OTG_VBUSCMP_EN;
- writel(tmp, port_base + U3P_USBPHYACR6);
+ writel(tmp, com + U3P_USBPHYACR6);
if (!index) {
/* switch 100uA current back to USB2.0 */
- tmp = readl(port_base + U3P_USBPHYACR5);
+ tmp = readl(com + U3P_USBPHYACR5);
tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
- writel(tmp, port_base + U3P_USBPHYACR5);
+ writel(tmp, com + U3P_USBPHYACR5);
}
/* let suspendm=0, set utmi into analog power down */
- tmp = readl(port_base + U3P_U2PHYDTM0);
+ tmp = readl(com + U3P_U2PHYDTM0);
tmp &= ~P2C_RG_SUSPENDM;
- writel(tmp, port_base + U3P_U2PHYDTM0);
+ writel(tmp, com + U3P_U2PHYDTM0);
udelay(1);
- tmp = readl(port_base + U3P_U2PHYDTM1);
+ tmp = readl(com + U3P_U2PHYDTM1);
tmp &= ~(P2C_RG_VBUSVALID | P2C_RG_AVALID);
tmp |= P2C_RG_SESSEND;
- writel(tmp, port_base + U3P_U2PHYDTM1);
+ writel(tmp, com + U3P_U2PHYDTM1);
if (u3phy->pdata->avoid_rx_sen_degradation && index) {
- tmp = readl(port_base + U3D_U2PHYDCR0);
+ tmp = readl(com + U3D_U2PHYDCR0);
tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
- writel(tmp, port_base + U3D_U2PHYDCR0);
+ writel(tmp, com + U3D_U2PHYDCR0);
}
dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
@@ -402,18 +437,55 @@ static void phy_instance_power_off(struct mt65xx_u3phy
*u3phy,
static void phy_instance_exit(struct mt65xx_u3phy *u3phy,
struct mt65xx_phy_instance *instance)
{
- void __iomem *port_base = instance->port_base;
+ struct u2phy_banks *u2_banks = &instance->u2_banks;
+ void __iomem *com = u2_banks->com;
u32 index = instance->index;
u32 tmp;
if (u3phy->pdata->avoid_rx_sen_degradation && index) {
- tmp = readl(port_base + U3D_U2PHYDCR0);
+ tmp = readl(com + U3D_U2PHYDCR0);
tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
- writel(tmp, port_base + U3D_U2PHYDCR0);
+ writel(tmp, com + U3D_U2PHYDCR0);
- tmp = readl(port_base + U3P_U2PHYDTM0);
+ tmp = readl(com + U3P_U2PHYDTM0);
tmp &= ~P2C_FORCE_SUSPENDM;
- writel(tmp, port_base + U3P_U2PHYDTM0);
+ writel(tmp, com + U3P_U2PHYDTM0);
+ }
+}
+
+static void phy_v1_banks_init(struct mt65xx_u3phy *u3phy,
+ struct mt65xx_phy_instance *instance)
+{
+ struct u2phy_banks *u2_banks = &instance->u2_banks;
+ struct u3phy_banks *u3_banks = &instance->u3_banks;
+
+ if (instance->type == PHY_TYPE_USB2) {
+ u2_banks->misc = NULL;
+ u2_banks->fmreg = u3phy->sif_base + SSUSB_SIFSLV_V1_U2FREQ;
+ u2_banks->com = instance->port_base + SSUSB_SIFSLV_V1_U2PHY_COM;
+ } else if (instance->type == PHY_TYPE_USB3) {
+ u3_banks->spllc = u3phy->sif_base + SSUSB_SIFSLV_V1_SPLLC;
+ u3_banks->chip = NULL;
+ u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD;
+ u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V1_U3PHYA;
+ }
+}
+
+static void phy_v2_banks_init(struct mt65xx_u3phy *u3phy,
+ struct mt65xx_phy_instance *instance)
+{
+ struct u2phy_banks *u2_banks = &instance->u2_banks;
+ struct u3phy_banks *u3_banks = &instance->u3_banks;
+
+ if (instance->type == PHY_TYPE_USB2) {
+ u2_banks->misc = instance->port_base + SSUSB_SIFSLV_V2_MISC;
+ u2_banks->fmreg = instance->port_base + SSUSB_SIFSLV_V2_U2FREQ;
+ u2_banks->com = instance->port_base + SSUSB_SIFSLV_V2_U2PHY_COM;
+ } else if (instance->type == PHY_TYPE_USB3) {
+ u3_banks->spllc = instance->port_base + SSUSB_SIFSLV_V2_SPLLC;
+ u3_banks->chip = instance->port_base + SSUSB_SIFSLV_V2_CHIP;
+ u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V2_U3PHYD;
+ u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V2_U3PHYA;
}
}
@@ -490,7 +562,6 @@ static struct phy *mt65xx_phy_xlate(struct device *dev,
struct device_node *phy_np = args->np;
int index;
-
if (args->args_count != 1) {
dev_err(dev, "invalid number of cells in 'phy' property\n");
return ERR_PTR(-EINVAL);
@@ -508,13 +579,21 @@ static struct phy *mt65xx_phy_xlate(struct device *dev,
}
instance->type = args->args[0];
-
if (!(instance->type == PHY_TYPE_USB2 ||
instance->type == PHY_TYPE_USB3)) {
dev_err(dev, "unsupported device type: %d\n", instance->type);
return ERR_PTR(-EINVAL);
}
+ if (u3phy->pdata->version == MT_PHY_V1) {
+ phy_v1_banks_init(u3phy, instance);
+ } else if (u3phy->pdata->version == MT_PHY_V2) {
+ phy_v2_banks_init(u3phy, instance);
+ } else {
+ dev_err(dev, "phy version is not supported\n");
+ return ERR_PTR(-EINVAL);
+ }
+
return instance->phy;
}
@@ -528,14 +607,22 @@ static struct phy *mt65xx_phy_xlate(struct device *dev,
static const struct mt65xx_phy_pdata mt2701_pdata = {
.avoid_rx_sen_degradation = false,
+ .version = MT_PHY_V1,
+};
+
+static const struct mt65xx_phy_pdata mt2712_pdata = {
+ .avoid_rx_sen_degradation = false,
+ .version = MT_PHY_V2,
};
static const struct mt65xx_phy_pdata mt8173_pdata = {
.avoid_rx_sen_degradation = true,
+ .version = MT_PHY_V1,
};
static const struct of_device_id mt65xx_u3phy_id_table[] = {
{ .compatible = "mediatek,mt2701-u3phy", .data = &mt2701_pdata },
+ { .compatible = "mediatek,mt2712-u3phy", .data = &mt2712_pdata },
{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
{ },
};
@@ -571,11 +658,14 @@ static int mt65xx_u3phy_probe(struct platform_device
*pdev)
u3phy->dev = dev;
platform_set_drvdata(pdev, u3phy);
- sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- u3phy->sif_base = devm_ioremap_resource(dev, sif_res);
- if (IS_ERR(u3phy->sif_base)) {
- dev_err(dev, "failed to remap sif regs\n");
- return PTR_ERR(u3phy->sif_base);
+ if (u3phy->pdata->version == MT_PHY_V1) {
+ /* get banks shared by multiple phys */
+ sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ u3phy->sif_base = devm_ioremap_resource(dev, sif_res);
+ if (IS_ERR(u3phy->sif_base)) {
+ dev_err(dev, "failed to remap sif regs\n");
+ return PTR_ERR(u3phy->sif_base);
+ }
}
u3phy->u2ref_clk = devm_clk_get(dev, "u2ref_clk");
--
1.7.9.5
