Hi Kever,
Am Mittwoch, 5. April 2017, 17:33:19 CEST schrieb Kever Yang:
> Firefly-rk3399 is a bord from T-Firefly, you can find detail about
> it here:
> http://en.t-firefly.com/en/firenow/Firefly_RK3399/
>
> This patch add basic node for the board and make it able to bring
> up.
>
> Peripheral works:
> - usb hub which connect to ehci controller;
> - UART2 debug
> - eMMC
> - PCIe
>
> Not work:
> - USB 3.0 HOST, type-C port
> - sdio, sd-card
>
> Not test for other peripheral:
> - HDMI
> - Ethernet
> - OPTICAL
> - WiFi/BT
> - MIPI CSI/DSI
> - IR
> - EDP/DP
>
> Signed-off-by: Kever Yang <kever.y...@rock-chips.com>
[...]
> + vdd_log: vdd-log {
> + compatible = "pwm-regulator";
> + pwms = <&pwm2 0 25000 1>;
> + regulator-name = "vdd_log";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + /* for rockchip boot on */
> + rockchip,pwm_id= <2>;
> + rockchip,pwm_voltage = <1000000>;
Vendor-kernel stuff, needs to be dropped
[...]
> +&i2c0 {
> + status = "okay";
> + i2c-scl-rising-time-ns = <168>;
> + i2c-scl-falling-time-ns = <4>;
> + clock-frequency = <400000>;
> +
> + vdd_cpu_b: pmic@40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + vin-supply = <&vcc5v0_sys>;
> + regulator-compatible = "fan53555-reg";
> + regulator-name = "vdd_cpu_b";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + vsel-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
non-mainline property
> + fcs,suspend-voltage-selector = <0>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-state = <3>;
non-mainline property
> + regulator-state-mem {
indentation is wrong
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: syr828@41 {
> + compatible = "silergy,syr828";
> + reg = <0x41>;
> + vin-supply = <&vcc5v0_sys>;
> + regulator-compatible = "fan53555-reg";
> + regulator-name = "vdd_gpu";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-state = <3>;
non-mainline property
> + regulator-state-mem {
indentation is wrong
> + regulator-off-in-suspend;
> + };
> + };
> +
> + rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>;
> + rockchip,system-power-controller;
system-power-controller without the "rockchip,"?
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
[...]
> +&i2c1 {
> + status = "okay";
> + i2c-scl-rising-time-ns = <300>;
> + i2c-scl-falling-time-ns = <15>;
> +
> + gsl3673: gsl3673@40 {
gsl3673: touchscreen@40
> + compatible = "GSL,GSL3673";
compatible lowercase?
> + reg = <0x40>;
> + screen_max_x = <1536>;
> + screen_max_y = <2048>;
> + irq_gpio_number = <&gpio1 RK_PC4 IRQ_TYPE_LEVEL_LOW>;
> + rst_gpio_number = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
> + };
> +
> + rt5640: rt5640@1c {
> + #sound-dai-cells = <0>;
> + compatible = "realtek,rt5640";
> + reg = <0x1c>;
> + clocks = <&cru SCLK_I2S_8CH_OUT>;
> + clock-names = "mclk";
> + realtek,in1-differential;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rt5640_hpcon>;
> + hp-con-gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
> + io-channels = <&saradc 4>;
> + hp-det-adc-value = <500>;
these last 3 properties are not contained in the rt5640 binding
document on linux-next-20170407 .
> + };
> +};
> +
> +&i2c3 {
> + status = "okay";
> + i2c-scl-rising-time-ns = <450>;
> + i2c-scl-falling-time-ns = <15>;
> +};
> +
> +&i2c4 {
> + status = "okay";
> + i2c-scl-rising-time-ns = <600>;
> + i2c-scl-falling-time-ns = <20>;
> +
> + fusb0: fusb30x@22 {
fusb0: usb-typec@22 or so
Also that device is not in mainline yet, so has no approved binding
so should not be included right now.
> + compatible = "fairchild,fusb302";
> + reg = <0x22>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&fusb0_int>;
> + int-n-gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
> + vbus-5v-gpios = <&gpio2 RK_PA0 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> + };
> +
> + mpu6500@68 {
accelerometer@68
> + status = "okay";
> + compatible = "invensense,mpu6500";
> + reg = <0x68>;
> + irq-gpio = <&gpio1 RK_PC6 IRQ_TYPE_EDGE_RISING>;
> + mpu-int_config = <0x10>;
> + mpu-level_shifter = <0>;
> + mpu-orientation = <0 1 0 1 0 0 0 0 1>;
> + orientation-x= <1>;
> + orientation-y= <0>;
> + orientation-z= <0>;
> + mpu-debug = <1>;
> + };
> +};
> +
[...]
> +&u2phy0 {
> + status = "okay";
> + extcon = <&fusb0>;
see comment for fusb302
> +
> + u2phy0_otg: otg-port {
> + status = "okay";
> + };
> +
> + u2phy0_host: host-port {
> + phy-supply = <&vcc5v0_host>;
> + status = "okay";
> + };
> +};
> +
Heiko
