Hi,
On Thu, Apr 13, 2017 at 07:15:57PM +0200, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.ba...@st.com>
>
> The quadspi is a specialized communication interface targeting single,
> dual or quad SPI Flash memories.
>
> It can operate in any of the following modes:
> -indirect mode: all the operations are performed using the quadspi
> registers
> -read memory-mapped mode: the external Flash memory is mapped to the
> microcontroller address space and is seen by the system as if it was
> an internal memory
>
> Signed-off-by: Ludovic Barre <ludovic.ba...@st.com>
> ---
> drivers/mtd/spi-nor/Kconfig | 7 +
> drivers/mtd/spi-nor/Makefile | 1 +
> drivers/mtd/spi-nor/stm32-quadspi.c | 694
> ++++++++++++++++++++++++++++++++++++
> 3 files changed, 702 insertions(+)
> create mode 100644 drivers/mtd/spi-nor/stm32-quadspi.c
>
> diff --git a/drivers/mtd/spi-nor/Kconfig b/drivers/mtd/spi-nor/Kconfig
> index 7252087..bfdfb1e 100644
> --- a/drivers/mtd/spi-nor/Kconfig
> +++ b/drivers/mtd/spi-nor/Kconfig
> @@ -106,4 +106,11 @@ config SPI_INTEL_SPI_PLATFORM
> To compile this driver as a module, choose M here: the module
> will be called intel-spi-platform.
>
> +config SPI_STM32_QUADSPI
> + tristate "STM32 Quad SPI controller"
> + depends on ARCH_STM32
> + help
> + This enables support for the STM32 Quad SPI controller.
> + We only connect the NOR to this controller.
> +
> endif # MTD_SPI_NOR
> diff --git a/drivers/mtd/spi-nor/Makefile b/drivers/mtd/spi-nor/Makefile
> index 72238a7..285aab8 100644
> --- /dev/null
> +++ b/drivers/mtd/spi-nor/stm32-quadspi.c
> @@ -0,0 +1,694 @@
...
> +static int stm32_qspi_flash_setup(struct stm32_qspi *qspi,
> + struct device_node *np)
> +{
> + u32 width, flash_read, presc, cs_num, max_rate = 0;
> + struct stm32_qspi_flash *flash;
> + struct mtd_info *mtd;
> + int ret;
> +
> + of_property_read_u32(np, "reg", &cs_num);
> + if (cs_num >= STM32_MAX_NORCHIP)
> + return -EINVAL;
> +
> + of_property_read_u32(np, "spi-max-frequency", &max_rate);
> + if (!max_rate)
> + return -EINVAL;
> +
> + presc = DIV_ROUND_UP(qspi->clk_rate, max_rate) - 1;
> +
> + if (of_property_read_u32(np, "spi-rx-bus-width", &width))
Can we move handling of this into spi-nor.c sometime? This is the 2nd
driver that wants this. And in this case, there's absolutely no
driver-specific handling for it. (For nxp-spifi.c, the hanling looks a
little wrong anyway -- the DT could have a larger bus width, but the
flash might only support a smaller. So the driver should gracefull
downgrade *after* we detect this, I think.)
Not a blocker for now, but just room for future work.
Brian
> + width = 1;
> +
> + if (width == 4)
> + flash_read = SPI_NOR_QUAD;
> + else if (width == 2)
> + flash_read = SPI_NOR_DUAL;
> + else if (width == 1)
> + flash_read = SPI_NOR_NORMAL;
> + else
> + return -EINVAL;
[...]
Brian
